Signal Processors
| Description | Downloads | Specs | Ordering | ||
|---|---|---|---|---|---|
 |
Stereo to Mono RCA AdapterA2518 NEW |
| This unit is designed to convert stereo audio signals into a summed mono line level RCA signal. | ||
 |
Unbalanced To Balanced Converter XLR-RCA /...A2516 NEW |
|
| Unbalanced 10K Ohm 2 x RCA to balanced 600 Ohm 3 pin male XLR (or optional screw terminal connections) with level control. | |
 |
Balanced To Unbalanced Converter XLR-RCA /...A2515 NEW |
|
| Balanced 600 Ohm 3 pin female XLR to unbalanced 10K Ohm 2 x RCA with level control (or optional screw terminal connections). | |
 |
4x8 Stereo Audio Switcher SystemA4460 |
|
| Designed to distribute 4 stereo audio input sources to 8 stereo output zones, this system is ideal for use in function centres, hotels, meeting rooms and domestic homes etc. It sends audio sources from one room to another with total ease. | |
 |
3 Input XLR Mic/Line Pre-Amp Bluetooth Wal...A4937 NEW |
|
| These local zone input wallplates allow for multiple mic/line inputs to be sent over UTP cabling back to a single UTP receiver for connection to a zone amplifier. This model also features bluetooth audio streaming for local zone playback of music. | |
 |
Telephone Line Isolation UnitA0642B |
| By law any radio, amplifier etc connected to a telephone system (for background music or paging applications) must be isolated with a line isolation unit (LIU). Adjustable output level suits all telephone systems. | ||
 |
5 Pin XLR Cat5 Extender (Receiver)A4954 |
| The Redback® A 4954 receives audio from compatible Redback® Cat5e/6 transmitters and converts the signal to a balanced XLR output with PTT connection. | ||
 |
5 Pin XLR Cat5 Extender (Transmitter)A4952 |
| This handy interface box allows balanced signals to be transmitted over long distances using economical UTP data cabling, and provides easy local zone connection for audio sources. | ||
 |
5 Pin XLR Transmitter WallplateA4953 |
|
| This handy interface wallplate allows balanced signals to be transmitted over long distances using economical UTP data cabling. | |
 |
3 Pin XLR Transmitter WallplateA4941 |
|
| This handy interface wallplate allows balanced signals to be transmitted over long distances using economical UTP data cabling. | |
 |
Selection Panel 10 Zone PAA2080C |
|
| Enables the control of paging and background music over 10 speaker zones. An incoming signal is thus selectable to the zones required. | |
 |
3 Input XLR Mic/Line Pre-Amplifier WallplateA4935 |
|
| These local zone input wallplates allow for multiple mic/line inputs to be sent over UTP cabling back to a single receiver for connection to a zone amplifier. | |
 |
Line Level Compressor/LimiterA4948 |
|
| This compact module is designed to go inline with an audio input source like CD/Blu-Ray etc to the input of a mixer or amplifier. It maintains a constant level to the mixer/amp regardless of the amplitude of the input signal. | |
 |
Paging Microphone Chime ModuleA4950 |
|
| By adding this module inline with a paging microphone pre and post announcement chimes can be added to the audio signal. | |
 |
5.1CH Digital Audio ConverterA3195A |
|
| This Audio decoder can auto convert optical/coaxial channel (Support LPCM/PCM/RAW) input to 2.0 channel analog audio output, and supports decoding Dolby AC-3/DTS (included 5.1 RAW digital audio streaming). | |
 |
RCA to Cat5 Extender (Receiver)A4946 |
| The Redback A 4946 receives audio from compatible Redback Cat5e/6 transmitters, converts the signal to line level and outputs to RCA and 3.5mm connectors. | ||
 |
RCA to Cat5 Extender (Transmitter)A4944 |
| The Redback® A 4944 provides a convenient way to send line level RCA audio signals over long distances via Cat5/6 cabling. The unit has DIP switch selectable input sensitivities of 100mV and 1V to handle inputs of varying levels. | ||
 |
3 Pin XLR Cat5 Extender (Receiver)A4942 |
|
| The Redback® A 4942 receives audio from compatible Redback® Cat5e/6 transmitters and converts the signal to a balanced XLR output. The output level is DIP switch selectable, and the ouput volume is screwdriver adjusted via the trimpot on the front of the unit. | |
 |
3 Pin XLR Cat5 Extender (Transmitter)A4940 |
|
| Allows balanced signals to be transmitted over long distances using economical UTP data cabling. | |
 |
Dante Mic/Line 4 Input, 4 Output Dual Wall...A4818 |
|
| Dante Interface 4 x Mic/Line Inputs, 4 x Outputs | |
 |
Phono Preamp with AUX inputA3052 |
|
| This phono preamp can be used to raise your turntable's output to make it compatible with modern amplifiers. At the same time, it adds standardised equalisation. Users may need this phono preamp because their turntable either doesn't have one, in which case they won't be able to play records without one. | |
 |
Digital Audio Cat5 Extender BoxA3194 |
|
| Allows digital signals to be transmitted using a single Cat5e or Cat6 cable. | |
 |
Dante Mic/Line 4 Input, 2 Output Dual Wall...A4816 |
|
| Dante Interface 4 x Mic/Line Inputs, 2 x Line Outputs | |
 |
Hum and Noise Eliminating Audio CouplerC9555A |
|
| A very handy 2 channel inline transformer coupler enabling the interconnection of audio modules without introducing hum and buzz, etc. Typical uses are: * Car sound - Enabling connection from receiver/player to power amplifier * Home theatre / Hi- | |
 |
Microphone/Line Pre Amplifier WallplateA4931V |
|
| This mic/line pre-amp wallplate accepts either a microphone or line input and converts the signal to a balanced high level output. The 3V output signal is carried via Cat5e cable, (suitable for distribution up to 300m without interference) back to the A 4930 Hub. | |
 |
Balanced Microphone/Line Pre AmplifierA4932 |
|
| This mic/line pre-amp wallplate accepts either a microphone or line input and converts the signal to a balanced high level output. The 3V output signal is carried via Cat5e cable, (suitable for distribution up to 300m without interference) back to the A 4930 Hub. | |
 |
Active Three Pair Audio Signal Distributio...A4835 |
|
| This audio distribution system uses affordable UTP cabling to send up to three balanced inputs (terminal block) or mono RCA signals over long distances. | |
 |
Active Three Pair Audio Signal Distributio...A4834 |
|
| This audio distribution system uses affordable UTP cabling to send up to three balanced inputs (terminal block) or mono RCA signals over long distances. | |
 |
Local Input/Output Hub Interface BoxA4832 |
|
| A compact system hub for interfacing input and output wallplates together with existing zone audio amplifiers and audio sources. | |
 |
Dante 2 Input 4 Output Converter Interface...A4831 |
| Interfaces 2 input and 4 output CSP UTP wallplates with Dante® systems | ||
 |
Dante Input/Output Converter Interface BoxA4830 |
| Interfaces 1 input and 1 output CSP UTP wallplates with Dante® systems. | ||
 |
Stereo RCA Jack Output UTP Balun WallplateA4828 |
|
| This Stereo RCA Jack output wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | |
 |
3 Pin XLR Line/Balanced Output UTP Balun W...A4827 |
|
| This 3 pin XLR Balanced Output wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | |
 |
3 Pin XLR Balanced & Stereo RCA Output UTP...A4826 |
|
| This 3 pin XLR Balanced and Stereo RCA output wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | |
 |
Dual 3 Pin XLR Input UTP Balun WallplateA4825 |
|
| This Dual 3 pin XLR Line/Balanced input wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | |
 |
3 Pin XLR & Stereo RCA Input UTP Balun Wal...A4824 |
|
| This 3 pin XLR Line/Balanced and Stereo RCA input wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | |
 |
Stereo RCA Input UTP Balun WallplateA4822 |
|
| This Stereo RCA input wallplate can be used in a stand-alone point to point basis, allowing signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | |
 |
Stereo RCA and 3.5mm Jack Input UTP Balun ...A4821 |
|
| This Stereo RCA and 3.5mm Jack Wallaplate can be used in a stand-alone point to point basis, allowing signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | |
 |
3 Pin XLR Line/Balanced Input UTP Balun Wa...A4820 |
|
| This 3 pin XLR Line/Balanced input wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | |
 |
Single Output Microphone/Line HubA4928 |
|
| A single mic/line output box designed to operate with A 4931 and A 4932 zone connection boxes. | |
 |
2 Channel Audio Output Converter (High to ...C9620A |
| This unit will convert speaker level output from a head unit to a low level input suitable for feeding directly into an amplifier input. | ||
 |
Microphone/Line Pre Amplifier WallplateA4931 |
|
| This mic/line pre-amp wallplate accepts either a microphone or line input and converts the signal to a balanced high level output. The 3V output signal is carried via Cat5e cable, (suitable for distribution up to 300m without interference) back to the A 4930 Hub. | |
 |
Four Output Microphone/Line HubA4930 |
|
| This Microphone/Line Hub is designed to accept audio from up to four A 4931 Mic/Line Preamp wallplates. The Hub has a dedicated output for each wall plate, with front mounted volume controls for each output. | |
 |
Audio Over IP Dante POE TransmitterA3165 |
|
| This device is designed to provide two channels audio signal to the Dante network by the Euro terminal input. Simply use Cat5 cable to connect the RJ45 port to an Ethernet switch, and using "Dante controller" to route the low latency of signal to other devices which already connected on the same Dante network. | |
 |
Audio Over IP Dante POE ReceiverA3164 |
|
| This device is designed to receive two channels audio signal from the Dante network, and converts to analogue RCA outputs. Simply use Cat5 cable to connect the RJ45 port to an Ethernet switch, and using "Dante controller" to receive the low latency of signal from other devices which already connected on the same Dante network. | |
 |
Passive DI BoxA2510A |
|
| Direct injection (DI) boxes are used to convert high impedance unbalanced signals from guitars or other musical instrument pickups to a low level balanced output signal. This enables the signal to be transported over long distances without picking up noise or hum. Earth and hum loops are isolated from powered equipment such as keyboards. | |
 |
Hum and Noise Eliminating Audio Coupler 3.5mmC9556 |
|
| A very handy 2 channel inline transformer coupler enabling the interconnection of audio modules without introducing hum and buzz, etc. uses stereo 3.5mm connections | |
 |
2 Channel Microphone Mixer Pre-AmplifierA3044 |
|
| Dual microphone preamplifiers that can be mixed in stereo or operated separately. Dual inputs, Dual outputs. Includes 12V power supply. | |
 |
Compact Stereo Line Pre-AmplifierA3042 |
|
| This compact stereo pre-amplifier is a great way to boost the output from your mobile devices and anything else with a low output. | |
 |
100V Line to Low Level AdapterA4903A |
|
| This small adaptor receives a 100V signal from one amplifier and reduces the level down to either balanced mic level or auxiliary level to feed into the input of a second amplifier. |
100% developed, designed & assembled in Australia.
Backed by an industry leading 10 Year Manufacturer Warranty.
