Signal Processors
| Description | Downloads | Specs | Ordering | ||
|---|---|---|---|---|---|
 |
Unbalanced to Balanced Converter RCA-XLRA2514 |
| Unbalanced 10K Ohm 2 x RCA to balanced 600 Ohm 3 pin male XLR with level control. -10dB max signal gain. | ||
 |
Balanced To Unbalanced Converter XLR-RCAA2513 |
| Balanced 600 Ohm 3 pin female XLR to unbalanced 10K Ohm 2 x RCA with level control. +10dB max signal gain. Steps up input signal by factor of 16, ie 20mV in = 320mV out. | ||
 |
100V Line to Low Level AdapterA4903A |
|
| This small adaptor receives a 100V signal from one amplifier and reduces the level down to either balanced mic level or auxiliary level to feed into the input of a second amplifier. | |
 |
Mic/Line Pre-Amplifier to Line Level Out C...A4905 |
|
| This line pre-amp will accept either a microphone or auxiliary input and convert it to a balanced high level signal suitable for distribution up to 500M without interference with up to 3V of output level available. Volume controls are provided for both inputs plus a master volume control. The microphone is a balanced XLR input whilst the auxiliary | |
 |
Unbalanced Stereo Line Isolation Transform...A2517 |
| Unbalanced stereo 2 x RCA to unbalanced stereo 2 x RCA. | ||
 |
Compact Stereo Line Pre-AmplifierA3042 |
|
| This compact stereo pre-amplifier is a great way to boost the output from your mobile devices and anything else with a low output. | |
 |
Headphone AmplifierA3196 |
|
| This single channel headphone amplifier is ideal for systems requiring additional audio level due to impedance differences between the audio source and headphone. | |
 |
Audio Over IP Dante POE ReceiverA3164 |
|
| This device is designed to receive two channels audio signal from the Dante network, and converts to analogue RCA outputs. Simply use Cat5 cable to connect the RJ45 port to an Ethernet switch, and using "Dante controller" to receive the low latency of signal from other devices which already connected on the same Dante network. | |
 |
2 Channel Microphone Mixer Pre-AmplifierA3044 |
|
| Dual microphone preamplifiers that can be mixed in stereo or operated separately. Dual inputs, Dual outputs. Includes 12V power supply. | |
 |
2 Channel Audio Output Converter (High to ...C9620A |
| This unit will convert speaker level output from a head unit to a low level input suitable for feeding directly into an amplifier input. | ||
 |
1 In to 2 Out Audio SplitterA4904 |
|
| This compact signal splitter is provided with two input sockets. The 3 pin XLR can be configured for either 3mV or 1V sensitivity, whilst the RCA auxiliary input can be set for either 100mV or 1V sensitivity. | |
 |
Mic/Line/100V Input to Line +24V Switched ...A4906 |
|
| The A 4906 is a versatile unit which accepts either a line level signal, balanced microphone signal or 100V input signal. The output signal is a line level signal suitable for feeding into an amplifier. | |
 |
5.1CH Digital Audio ConverterA3195A |
|
| This Audio decoder can auto convert optical/coaxial channel (Support LPCM/PCM/RAW) input to 2.0 channel analog audio output, and supports decoding Dolby AC-3/DTS (included 5.1 RAW digital audio streaming). | |
 |
4 Channel Headphone Distribution AmplifierA2630 |
|
| A compact headphone amplifier featuring four individual channels with volume controls. Ideally suited to monitoring in band and stage environments, it can also be used in educational situations such as language labs. Amplification and individual volume c | |
 |
Phono Preamp with AUX inputA3052 |
|
| This phono preamp can be used to raise your turntable's output to make it compatible with modern amplifiers. At the same time, it adds standardised equalisation. Users may need this phono preamp because their turntable either doesn't have one, in which case they won't be able to play records without one. | |
 |
Balanced Mic / Line Input Pre-Amp & MixerA2055A |
|
| Features two line inputs and one mic input, each with its own level control. The mic input can be configured for either balanced or unbalanced operation. All inputs are mixed to a single line level output. It can be powered from either a single rail po | |
 |
Line Isolation Transformer 10k ohms to 10k...A2524 |
| Balanced 10kΩ to 10kΩ balanced 3 pin male XLR with earth lift switch. | ||
 |
Line Isolation Transformer 10k ohms to 600...A2522 |
| Balanced 600Ω to 600Ω balanced 3 pin male XLR with earth lift switch. | ||
 |
Line Isolation Transformer 600 ohms to 600...A2519 |
| Balanced 600Ω to 600Ω balanced 3 pin male XLR with earth lift switch. | ||
 |
Single Output Microphone/Line HubA4928 |
|
| A single mic/line output box designed to operate with A 4931 and A 4932 zone connection boxes. | |
 |
Hum and Noise Eliminating Audio CouplerC9555A |
|
| A very handy 2 channel inline transformer coupler enabling the interconnection of audio modules without introducing hum and buzz, etc. Typical uses are: * Car sound - Enabling connection from receiver/player to power amplifier * Home theatre / Hi- | |
 |
Microphone/Line Pre Amplifier WallplateA4931 |
|
| This mic/line pre-amp wallplate accepts either a microphone or line input and converts the signal to a balanced high level output. The 3V output signal is carried via Cat5e cable, (suitable for distribution up to 300m without interference) back to the A 4930 Hub. | |
 |
Hum and Noise Eliminating Audio Coupler 3.5mmC9556 |
|
| A very handy 2 channel inline transformer coupler enabling the interconnection of audio modules without introducing hum and buzz, etc. uses stereo 3.5mm connections | |
 |
Audio Over IP Dante POE TransmitterA3165 |
|
| This device is designed to provide two channels audio signal to the Dante network by the Euro terminal input. Simply use Cat5 cable to connect the RJ45 port to an Ethernet switch, and using "Dante controller" to route the low latency of signal to other devices which already connected on the same Dante network. | |
 |
Four Output Microphone/Line HubA4930 |
|
| This Microphone/Line Hub is designed to accept audio from up to four A 4931 Mic/Line Preamp wallplates. The Hub has a dedicated output for each wall plate, with front mounted volume controls for each output. | |
 |
Passive DI BoxA2510A |
|
| Direct injection (DI) boxes are used to convert high impedance unbalanced signals from guitars or other musical instrument pickups to a low level balanced output signal. This enables the signal to be transported over long distances without picking up noise or hum. Earth and hum loops are isolated from powered equipment such as keyboards. | |
 |
Digital Audio Cat5 Extender BoxA3194 |
|
| Allows digital signals to be transmitted using a single Cat5e or Cat6 cable. | |
 |
Selection Panel 10 Zone PAA2080B |
|
| Enables the control of paging and background music over 10 speaker zones. An incoming signal is thus selectable to the zones required. An &ldquoall call&rdquo button is provided. The design allows multiple units to be connected together to create an infinite number of zones. | |
 |
Microphone/Line Pre Amplifier WallplateA4931V |
|
| This mic/line pre-amp wallplate accepts either a microphone or line input and converts the signal to a balanced high level output. The 3V output signal is carried via Cat5e cable, (suitable for distribution up to 300m without interference) back to the A 4930 Hub. | |
 |
3 Input XLR Mic/Line Pre-Amplifier WallplateA4935 |
|
| These local zone input wallplates allow for multiple mic/line inputs to be sent over UTP cabling back to a single receiver for connection to a zone amplifier. | |
 |
3 Input XLR Mic/Line Pre-Amp Bluetooth Wal...A4937 NEW |
|
| These local zone input wallplates allow for multiple mic/line inputs to be sent over UTP cabling back to a single UTP receiver for connection to a zone amplifier. This model also features bluetooth audio streaming for local zone playback of music. | |
 |
Unbalanced To Balanced Converter XLR-RCA /...A2516 NEW |
|
| Unbalanced 10K Ohm 2 x RCA to balanced 600 Ohm 3 pin male XLR (or optional screw terminal connections) with level control. | |
 |
Telephone Line Isolation UnitA0642B |
| By law any radio, amplifier etc connected to a telephone system (for background music or paging applications) must be isolated with a line isolation unit (LIU). Adjustable output level suits all telephone systems. | ||
 |
Dante Input/Output Converter Interface BoxA4830 |
| Interfaces 1 input and 1 output CSP UTP wallplates with Dante® systems. | ||
 |
Stereo to Mono RCA AdapterA2518 NEW |
| This unit is designed to convert stereo audio signals into a summed mono line level RCA signal. | ||
 |
Balanced To Unbalanced Converter XLR-RCA /...A2515 NEW |
|
| Balanced 600 Ohm 3 pin female XLR to unbalanced 10K Ohm 2 x RCA with level control (or optional screw terminal connections). | |
 |
Dante Mic/Line 4 Input, 4 Output Dual Wall...A4818 |
|
| Dante Interface 4 x Mic/Line Inputs, 4 x Outputs | |
 |
2 Channel 31 Band EQ With Feedback DetectionA5332 |
|
| This professional unit delivers outstanding equalisation both in live or studio applications. Invaluable for counteracting poor room or venue acoustics. The design employs ultra low noise audio amplifiers with high quality components for outstanding sou | |
 |
3 Pin XLR & Stereo RCA Input UTP Balun Wal...A4824 |
|
| This 3 pin XLR Line/Balanced and Stereo RCA input wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | |
 |
3 Pin XLR Line/Balanced Input UTP Balun Wa...A4820 |
|
| This 3 pin XLR Line/Balanced input wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | |
 |
Stereo RCA and 3.5mm Jack Input UTP Balun ...A4821 |
|
| This Stereo RCA and 3.5mm Jack Wallaplate can be used in a stand-alone point to point basis, allowing signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | |
 |
Dual 3 Pin XLR Input UTP Balun WallplateA4825 |
|
| This Dual 3 pin XLR Line/Balanced input wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | |
 |
Dante 2 Input 4 Output Converter Interface...A4831 |
| Interfaces 2 input and 4 output CSP UTP wallplates with Dante® systems | ||
 |
Local Input/Output Hub Interface BoxA4832 |
|
| A compact system hub for interfacing input and output wallplates together with existing zone audio amplifiers and audio sources. | |
 |
Active Three Pair Audio Signal Distributio...A4834 |
|
| This audio distribution system uses affordable UTP cabling to send up to three balanced inputs (terminal block) or mono RCA signals over long distances. | |
 |
3 Pin XLR Cat5 Extender (Receiver)A4942 |
|
| The Redback® A 4942 receives audio from compatible Redback® Cat5e/6 transmitters and converts the signal to a balanced XLR output. The output level is DIP switch selectable, and the ouput volume is screwdriver adjusted via the trimpot on the front of the unit. | |
 |
3 Pin XLR Cat5 Extender (Transmitter)A4940 |
|
| Allows balanced signals to be transmitted over long distances using economical UTP data cabling. | |
 |
3 Pin XLR Balanced & Stereo RCA Output UTP...A4826 |
|
| This 3 pin XLR Balanced and Stereo RCA output wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | |
 |
Dante Mic/Line 4 Input, 2 Output Dual Wall...A4816 |
|
| Dante Interface 4 x Mic/Line Inputs, 2 x Line Outputs | |
 |
3 Pin XLR Line/Balanced Output UTP Balun W...A4827 |
|
| This 3 pin XLR Balanced Output wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). |
