|
Description |
Downloads |
Specs |
Ordering |
|
 |
A4935 |
|
- Standard dual gang wallplate
- Connects via RJ45 UTP cabling
- Mixed audio output
- Connects to A 4942 balanced UTP receiver or other Redback UTP compatible products.
- Individual & master level controls
- Stereo RCA input
- 24V DC input via Cat5 UTP cable from connected equipment
- 3 pin XLR mic/line level inputs
|
|
These local zone input wallplates allow for multiple mic/line inputs to be sent over UTP cabling back to a single receiver for connection to a zone amplifier. |
 |
A4937 NEW
|
|
- Standard dual gang wallplate
- Connects via RJ45 UTP cabling
- Mixed audio output
- Bluetooth 5.1 audio streaming receiver in-built
- 30m clear light of sight BT streaming range.
- Connects to A 4942 balanced UTP receiver or other Redback UTP compatible products.
- Individual & master level controls
- Stereo RCA input
- 24V DC input via Cat5 UTP cable from connected equipment
- 3 pin XLR mic/line level inputs
|
|
These local zone input wallplates allow for multiple mic/line inputs to be sent over UTP cabling back to a single UTP receiver for connection to a zone amplifier. This model also features bluetooth audio streaming for local zone playback of music. |
 |
A4825 |
|
- Two Balanced Microphone XLR Inputs
- Switch-Selectable Mic Gain and 48V Phantom Power on Side Panel
- Output Pair Selectors to go to Pair (A, B or C) for Each MIC Input
- Signal and Power Pairs Pass-Through on RJ45 jacks
- Daisy-Chain with a Single-Pair UTP Sender
- AFC Design (AFC: Auto Feedback Gain Circuitry)
|
|
This Dual 3 pin XLR Line/Balanced input wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). |
 |
A2080B |
|
- 19" rack mount
- 10 zones & “All Call”
- 50W per zone
- Requires no power
- Units can be ganged together more zones
- Zone ID strip included
|
|
Enables the control of paging and background music over 10 speaker zones. An incoming signal is thus selectable to the zones required. An &ldquoall call&rdquo button is provided. The design allows multiple units to be connected together to create an infinite number of zones. |
 |
A2080C |
|
- 19" rack mount
- 10 zones & “All Call”
- Requires no power
- Units can be ganged together more zones
- Zone ID strip included
|
|
Enables the control of paging and background music over 10 speaker zones. An incoming signal is thus selectable to the zones required. |
 |
A4930 |
|
- Connects to A 4931 transmitter wallplate or other Redback UTP transmitter (see connection matrix)
- Connect up to four audio zones together.
- Easy Cat5e/6 UTP data cabling connection.
- Up to 300m cable runs out to zones.
- Balanced Euro terminal block connections.
- Balanced mic or line level operation.
- 24V DC operation.
- Australian designed & assembled.
|
|
This Microphone/Line Hub is designed to accept audio from up to four A 4931 Mic/Line Preamp wallplates. The Hub has a dedicated output for each wall plate, with front mounted volume controls for each output. |
 |
A4830 |
|
|
|
Interfaces 1 input and 1 output CSP UTP wallplates with Dante® systems. |
 |
A3164 |
|
- Dante Interface for Audio Input.
- RCA output Jacks on front panel.
- Converts Dante Audio Signal to Unbalanced Line Level.
- Selectable Dante Sample Rates: 44.1 kHz ~ 96 kHz.
- High Resolution Digital to Analog Conversion
- Power over Ethernet (PoE).
- Excellent Audio quality
|
|
This device is designed to receive two channels audio signal from the Dante network, and converts to analogue RCA outputs. Simply use Cat5 cable to connect the RJ45 port to an Ethernet switch, and using "Dante controller" to receive the low latency of signal from other devices which already connected on the same Dante network. |
 |
A3165 |
|
- Dante Interface for Audio Output
- Terminal Block Input Jack on front panel
- Converts Line Audio Signal to Dante Network
- Input Gain Control on front panel
- Dante Sample Rates Support: 44.1, 48, 88.2, 96KHz
- High Resolution Analog to Digital Conversion
- Power over Ethernet (PoE)
- Excellent Audio quality
|
|
This device is designed to provide two channels audio signal to the Dante network by the Euro terminal input. Simply use Cat5 cable to connect the RJ45 port to an Ethernet switch, and using "Dante controller" to route the low latency of signal to other devices which already connected on the same Dante network. |
 |
A5332 |
|
- Input impedance: 20KΩ (bal.)
- Maximum input level: ≥16dB
- Connections: Balanced XLR, 6.35mm jack
- Output impedance: 100Ω
- Maximum output level: ≥15dB
- Equaliser control 31 band (1/3 octave)
- High pass filter: 40Hz 12dB/octave
- Feedback threshold LED: ≥-22dB
- Peak sensitivity: Lit 3dB before clip point
- Frequency response: 20Hz - 20KHz (±0.5dB)
- THD + S/N %: <0.1% (20Hz - 20KHz @ 0dB)
- S/N ratio: ≥90dB
- Power supply: 240VAC
- Dimensions: ≈482W x 230D x 132Hmm
- Weight: 5.4kg
|
|
This professional unit delivers outstanding equalisation both in live or studio applications. Invaluable
for counteracting poor room or venue acoustics. The design employs ultra low noise audio amplifiers
with high quality components for outstanding sou |
 |
A4831 |
|
|
|
Interfaces 2 input and 4 output CSP UTP wallplates with Dante® systems |
 |
A4816 |
|
- Four Mic/Line XLR Inputs on Front Panel
- Terminal Block for Two Audio Outputs on Rear Panel
- Converts Mic or Line Audio Signals to Dante network
- Mic or Line is Selectable for Each XLR Input
- Switchable 48V Phantom Power for Each Mic XLR Input
- Adjustable Mic/LIne Gain from ‐20 dB to +20dB for Each XLR input (Two Audio Signal Outputs from Dante Network)
- Balanced or Unbalanced Signal Outputs
- High Resolution 24 Bit for DAC and ADC
- Power over Ethernet (PoE) or 24VDC power supply
- Provides High Quality of Preamplifier for microphones
- Excellent Audio quality with low noise
|
|
Dante Interface 4 x Mic/Line Inputs, 2 x Line Outputs |
 |
A4460 |
|
- 4 in, 8 out stereo
- Touchscreen & iOS/Android app control
- Four external MP3 triggers
- Six wallplate activated triggers (master only)
- Remote wallplate control
- Global function to send to all zones
- System cabling via Cat5e UTP.
- Suits all size power amps
- Local Bluetooth inputs
- Master plate can control & set up all zones
- 24V DC operation
|
|
Designed to distribute 4 stereo audio input sources to 8 stereo output zones, this system is ideal for use in function centres, hotels, meeting rooms and domestic homes etc. It sends audio sources from one room to another with total ease. |
 |
A4818 |
|
- Two Mic/Line XLR Inputs and one mini-jack input on Front Panel
- Terminal Block for Two Audio Outputs on Rear Panel
- One mini-jack output on front panel
- Converts Mic or Line Audio Signals to Dante network
- Mic or Line is Selectable for Each XLR Input
- Switchable 48V Phantom Power for Each Mic XLR Input
- Adjustable Mic/LIne Gain from ‐20 dB to +20dB for Each XLR input (Two Audio Signal Outputs from Dante Network)
- Stereo/Mono switch for mini-jack input and output
- Four audio signal outputs from Dante network
- Balance or unbalanced signal outputs
- Doesn't require special software
- High Resolution 24 Bit for DAC and ADC
- Power over Ethernet (PoE) or 24VDC power supply
- Provides High Quality of Preamplifier for microphones
- Excellent Audio quality with low noise
|
|
Dante Interface 4 x Mic/Line Inputs, 4 x Outputs |
