Signal Processors
| Description | Downloads | Specs | Ordering | ||
|---|---|---|---|---|---|
 |
Passive DI BoxA2510A |
|
| Direct injection (DI) boxes are used to convert high impedance unbalanced signals from guitars or other musical instrument pickups to a low level balanced output signal. This enables the signal to be transported over long distances without picking up noise or hum. Earth and hum loops are isolated from powered equipment such as keyboards. | |
 |
Digital Audio Cat5 Extender BoxA3194 |
|
| Allows digital signals to be transmitted using a single Cat5e or Cat6 cable. | |
 |
Selection Panel 10 Zone PAA2080B |
|
| Enables the control of paging and background music over 10 speaker zones. An incoming signal is thus selectable to the zones required. An &ldquoall call&rdquo button is provided. The design allows multiple units to be connected together to create an infinite number of zones. | |
 |
Microphone/Line Pre Amplifier WallplateA4931V |
|
| This mic/line pre-amp wallplate accepts either a microphone or line input and converts the signal to a balanced high level output. The 3V output signal is carried via Cat5e cable, (suitable for distribution up to 300m without interference) back to the A 4930 Hub. | |
 |
3 Input XLR Mic/Line Pre-Amplifier WallplateA4935 |
|
| These local zone input wallplates allow for multiple mic/line inputs to be sent over UTP cabling back to a single receiver for connection to a zone amplifier. | |
 |
3 Input XLR Mic/Line Pre-Amp Bluetooth Wal...A4937 NEW |
|
| These local zone input wallplates allow for multiple mic/line inputs to be sent over UTP cabling back to a single UTP receiver for connection to a zone amplifier. This model also features bluetooth audio streaming for local zone playback of music. | |
 |
Unbalanced To Balanced Converter XLR-RCA /...A2516 NEW |
|
| Unbalanced 10K Ohm 2 x RCA to balanced 600 Ohm 3 pin male XLR (or optional screw terminal connections) with level control. | |
 |
Telephone Line Isolation UnitA0642B |
| By law any radio, amplifier etc connected to a telephone system (for background music or paging applications) must be isolated with a line isolation unit (LIU). Adjustable output level suits all telephone systems. | ||
 |
Dante Input/Output Converter Interface BoxA4830 |
| Interfaces 1 input and 1 output CSP UTP wallplates with Dante® systems. | ||
 |
Stereo to Mono RCA AdapterA2518 NEW |
| This unit is designed to convert stereo audio signals into a summed mono line level RCA signal. | ||
 |
Balanced To Unbalanced Converter XLR-RCA /...A2515 NEW |
|
| Balanced 600 Ohm 3 pin female XLR to unbalanced 10K Ohm 2 x RCA with level control (or optional screw terminal connections). | |
 |
Dante Mic/Line 4 Input, 4 Output Dual Wall...A4818 |
|
| Dante Interface 4 x Mic/Line Inputs, 4 x Outputs | |
 |
2 Channel 31 Band EQ With Feedback DetectionA5332 |
|
| This professional unit delivers outstanding equalisation both in live or studio applications. Invaluable for counteracting poor room or venue acoustics. The design employs ultra low noise audio amplifiers with high quality components for outstanding sou | |
 |
3 Pin XLR & Stereo RCA Input UTP Balun Wal...A4824 |
|
| This 3 pin XLR Line/Balanced and Stereo RCA input wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | |
 |
3 Pin XLR Line/Balanced Input UTP Balun Wa...A4820 |
|
| This 3 pin XLR Line/Balanced input wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | |
 |
Stereo RCA and 3.5mm Jack Input UTP Balun ...A4821 |
|
| This Stereo RCA and 3.5mm Jack Wallaplate can be used in a stand-alone point to point basis, allowing signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | |
 |
Dual 3 Pin XLR Input UTP Balun WallplateA4825 |
|
| This Dual 3 pin XLR Line/Balanced input wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | |
 |
Dante 2 Input 4 Output Converter Interface...A4831 |
| Interfaces 2 input and 4 output CSP UTP wallplates with Dante® systems | ||
 |
Local Input/Output Hub Interface BoxA4832 |
|
| A compact system hub for interfacing input and output wallplates together with existing zone audio amplifiers and audio sources. | |
 |
Active Three Pair Audio Signal Distributio...A4834 |
|
| This audio distribution system uses affordable UTP cabling to send up to three balanced inputs (terminal block) or mono RCA signals over long distances. | |
 |
3 Pin XLR Cat5 Extender (Receiver)A4942 |
|
| The Redback® A 4942 receives audio from compatible Redback® Cat5e/6 transmitters and converts the signal to a balanced XLR output. The output level is DIP switch selectable, and the ouput volume is screwdriver adjusted via the trimpot on the front of the unit. | |
 |
3 Pin XLR Cat5 Extender (Transmitter)A4940 |
|
| Allows balanced signals to be transmitted over long distances using economical UTP data cabling. | |
 |
3 Pin XLR Balanced & Stereo RCA Output UTP...A4826 |
|
| This 3 pin XLR Balanced and Stereo RCA output wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | |
 |
Dante Mic/Line 4 Input, 2 Output Dual Wall...A4816 |
|
| Dante Interface 4 x Mic/Line Inputs, 2 x Line Outputs | |
 |
Paging Microphone Chime ModuleA4950 |
|
| By adding this module inline with a paging microphone pre and post announcement chimes can be added to the audio signal. |
100% developed, designed & assembled in Australia.
Backed by an industry leading 10 Year Manufacturer Warranty.