Signal Processors
| Description | Downloads | Specs | Ordering | ||
|---|---|---|---|---|---|
 |
Balanced Mic / Line Input Pre-Amp & MixerA2055A |
|
| Features two line inputs and one mic input, each with its own level control. The mic input can be configured for either balanced or unbalanced operation. All inputs are mixed to a single line level output. It can be powered from either a single rail po | |
 |
Balanced Microphone/Line Pre AmplifierA4932 |
|
| This mic/line pre-amp wallplate accepts either a microphone or line input and converts the signal to a balanced high level output. The 3V output signal is carried via Cat5e cable, (suitable for distribution up to 300m without interference) back to the A 4930 Hub. | |
 |
Balanced To Unbalanced Converter XLR-RCAA2513 |
| Balanced 600 Ohm 3 pin female XLR to unbalanced 10K Ohm 2 x RCA with level control. +10dB max signal gain. Steps up input signal by factor of 16, ie 20mV in = 320mV out. | ||
 |
Balanced To Unbalanced Converter XLR-RCA /...A2515 NEW |
|
| Balanced 600 Ohm 3 pin female XLR to unbalanced 10K Ohm 2 x RCA with level control (or optional screw terminal connections). | |
 |
Compact Stereo Line Pre-AmplifierA3042 |
|
| This compact stereo pre-amplifier is a great way to boost the output from your mobile devices and anything else with a low output. | |
 |
Dante 2 Input 4 Output Converter Interface...A4831 |
| Interfaces 2 input and 4 output CSP UTP wallplates with Dante® systems | ||
 |
Dante Input/Output Converter Interface BoxA4830 |
| Interfaces 1 input and 1 output CSP UTP wallplates with Dante® systems. | ||
 |
Dante Mic/Line 4 Input, 2 Output Dual Wall...A4816 |
|
| Dante Interface 4 x Mic/Line Inputs, 2 x Line Outputs | |
 |
Dante Mic/Line 4 Input, 4 Output Dual Wall...A4818 |
|
| Dante Interface 4 x Mic/Line Inputs, 4 x Outputs | |
 |
Digital Audio Cat5 Extender BoxA3194 |
|
| Allows digital signals to be transmitted using a single Cat5e or Cat6 cable. | |
 |
Dual 3 Pin XLR Input UTP Balun WallplateA4825 |
|
| This Dual 3 pin XLR Line/Balanced input wallplate can be used in a stand-alone point to point basis, allowing balanced signals to be sent over long distances (up to 600m depending on cable used and configuration of plates). | |
 |
Four Output Microphone/Line HubA4930 |
|
| This Microphone/Line Hub is designed to accept audio from up to four A 4931 Mic/Line Preamp wallplates. The Hub has a dedicated output for each wall plate, with front mounted volume controls for each output. | |
 |
Headphone AmplifierA3196 |
|
| This single channel headphone amplifier is ideal for systems requiring additional audio level due to impedance differences between the audio source and headphone. | |
 |
Hum and Noise Eliminating Audio CouplerC9555A |
|
| A very handy 2 channel inline transformer coupler enabling the interconnection of audio modules without introducing hum and buzz, etc. Typical uses are: * Car sound - Enabling connection from receiver/player to power amplifier * Home theatre / Hi- | |
 |
Hum and Noise Eliminating Audio Coupler 3.5mmC9556 |
|
| A very handy 2 channel inline transformer coupler enabling the interconnection of audio modules without introducing hum and buzz, etc. uses stereo 3.5mm connections | |
 |
Line Isolation Transformer 10k ohms to 10k...A2524 |
| Balanced 10kΩ to 10kΩ balanced 3 pin male XLR with earth lift switch. | ||
 |
Line Isolation Transformer 10k ohms to 600...A2522 |
| Balanced 600Ω to 600Ω balanced 3 pin male XLR with earth lift switch. | ||
 |
Line Isolation Transformer 600 ohms to 600...A2519 |
| Balanced 600Ω to 600Ω balanced 3 pin male XLR with earth lift switch. | ||
 |
Local Input/Output Hub Interface BoxA4832 |
|
| A compact system hub for interfacing input and output wallplates together with existing zone audio amplifiers and audio sources. | |
 |
Mic/Line Pre-Amplifier to Line Level Out C...A4905 |
|
| This line pre-amp will accept either a microphone or auxiliary input and convert it to a balanced high level signal suitable for distribution up to 500M without interference with up to 3V of output level available. Volume controls are provided for both inputs plus a master volume control. The microphone is a balanced XLR input whilst the auxiliary | |
 |
Mic/Line/100V Input to Line +24V Switched ...A4906 |
|
| The A 4906 is a versatile unit which accepts either a line level signal, balanced microphone signal or 100V input signal. The output signal is a line level signal suitable for feeding into an amplifier. | |
 |
Microphone/Line Pre Amplifier WallplateA4931 |
|
| This mic/line pre-amp wallplate accepts either a microphone or line input and converts the signal to a balanced high level output. The 3V output signal is carried via Cat5e cable, (suitable for distribution up to 300m without interference) back to the A 4930 Hub. | |
 |
Microphone/Line Pre Amplifier WallplateA4931V |
|
| This mic/line pre-amp wallplate accepts either a microphone or line input and converts the signal to a balanced high level output. The 3V output signal is carried via Cat5e cable, (suitable for distribution up to 300m without interference) back to the A 4930 Hub. | |
 |
Paging Microphone Chime ModuleA4950 |
|
| By adding this module inline with a paging microphone pre and post announcement chimes can be added to the audio signal. | |
 |
Passive DI BoxA2510A |
|
| Direct injection (DI) boxes are used to convert high impedance unbalanced signals from guitars or other musical instrument pickups to a low level balanced output signal. This enables the signal to be transported over long distances without picking up noise or hum. Earth and hum loops are isolated from powered equipment such as keyboards. |
100% developed, designed & assembled in Australia.
Backed by an industry leading 10 Year Manufacturer Warranty.