|
Description |
Downloads |
Specs |
Ordering |
|
 |
Q0203B NEW
|
|
- 2 Channel Digital Oscilloscope + Arbitrary/Function Waveform Generator + Synchronising Signal + External Trigger
- Easy to use button layout
- Large and clear 7” true colour 24-bit display
- Oscilloscope: 1GSa/s Sample Rate, 100MHz Bandwidth
- Huge selection of auto measurement functions
- Powerful trigger functions: Edge, Pulse, Video, Slope, Overtime, Window, Pattern, Interval, Under Amp, UART, LIN, CAN, SPI, IIC
- Arbitrary/Function Waveform Generator: 25MHz, 12 bits resolution, 200MHz DDS, Arbitrary wave/square wave/sine wave/triangle wave/trapezoidal wave/pulse wave/DC
- Integrated USB host, support USB disk storage, USB interface system update
|
|
Perfect for those in R&D, product development or service of complex electronic equipment. This compact bench top oscilloscope features 2 channels with real-time sampling modes of 1GSa/s (25GS/s equivalent sampling rate). |
 |
Q1346 |
|
- POE test
- PING test
- Perform crosstalk test on network cable
- Test open, short or cross connection
- Measure length of telephone, network cabling up to 2000m
- Log data and measurements to internal Micro SD card
- Locate breakages
- Voltage detector in receiver end (50-1000V)
- Includes 8 remote units
- Voltage presence detection
- Includes carry case, charging lead and adaptors.
|
|
This comprehensive cable testing kit consists of three units. The main tester with 2.8" LCD screen, cable "sniffer" receiving unit and 8 remote identifiers. It is capable of measuring cable length, tracing cable location, continuity testing, PoE and Ping testing. It can be used with LAN, telephone cabling. |
 |
Q2012 |
|
- Detects field strength in hearing loop systems.
- Can be used in conjunction with Q 2014 tone generator for reliable hearing loop installation.
- Headphone output.
- Internal lithium battery for easy recharging.
- Engineered and manufactured in Australia.
|
|
Essential for all installers setting up and commissioning hearing
induction loop amplifier systems. It is ideally used in conjunction with the Redback® Q 2014 1kHz tone generator allowing
an installer to test the signal generated in the actual ‘loop’ of the system. |
 |
Q0102 |
|
- 2 channel digital oscilloscope + digital multimeter
- Easy to use button and screen layout
- Small enough for single hand operation
- Large, clear 2.8” 64K colour screen 320x240 resolution
- Oscilloscope: 250MSa/s Sample Rate, 40MHz Bandwidth
- USB C recharging with internal 2600mAh lithium battery
- Automatic frequency & amplitude measurement
- 4000 count 10A multimeter
|
|
The ultimate field testing accessory combining an digital storage oscilloscope and digital multimeter. It features 2 channels with real time sampling modes of 125MSa/s per channel (or 250MSa/s when used in single channel mode). 64K colour screen provides a clear view. |
 |
Q2115 |
|
- The DCA Pro is an advanced new design that includes a graphics display, USB port, PC Software and an enhanced component recognition library.Transistors (including Darlingtons and "digital" transistors), Silicon and Germanium types. Measures gain, VBE and leakage.
- MOSFETs, enhancement mode and depletion mode types. Measure on-threshold (at 5mA) and approx transconductance (for span of 3mA-5mA).
- JFETs, including normally off SiC types. Measures pinch-off voltage (at 1uA) and approx transconductance (for span of 3mA-5mA).
- IGBTs (insulated gate bipolar transistors). Measures on-threshold (at 5mA).
- Diodes and Diode networks.
- LEDs and bicolour LEDs (2 lead and 3 lead types).
- Zener Diodes with measurement of zener voltage up to 9V at 5mA.
- Voltage regulators (measures regulation voltage <8V, drop-out voltage, quiescent current). Note that some regulators are not stable without their decoupling caps and/or minimum load and cannot be tested by the DCA75.
- Triacs and Thyristors that require less than 10mA of gate current and holding current.
|
|
Our all new Peak Advanced Semiconductor Analyser will
Automatically identify part type (eg, Transistor, JFET, IGBT, Regulator, Zener, Diodes, etc). Automatically identify pinout (connect any way round).
|
 |
Q2007 NEW
|
|
- Suitable for 50V, 70V and 100V line speaker systems up to 5kW
- Also suitable for measuring low Impedance speaker loads of 4 -16Ω
- OLED display shows Impedance and Wattage of the load
- 1Ω to 20KΩ test range
- Auto ranging
- Display accuracy +/-10%
- Push button operation
- System Check Mode (20, 60 or unlimited minutes)
- 5V Rechargeable Lithium Polymer internal battery
- Low battery indication
- Buzzer and Haptic feedback option via Menu access
- USB Charging lead supplied
- Silicon Test Leads supplied
- Soft Carry Case Included
- Rugged yet easy to hold compact hand held case
|
|
An absolute necessity for all PA system installers. This impedance meter for ‘dummies’ designed and manufactured by Altronics calculates and displays speaker loads in watts. Lithium rechargeable version. |
 |
Q0207 |
|
- General information
- • markers: for amplitude/voltage and frequency/time
- • input coupling: DC, AC and GND
- • 8 bit resolution
- • storage of display and data
- • supply from USB port (500mA)*
- • dimensions: 100x100x35mm / 3,9x3,9x1.4"
- Spectrum analyser:
- • frequency range: 0 .. 120Hz to 12MHz
- • linear or logarithmic timescale
- • operating principle: FFT (Fast Fourier Transform) • FFT resolution: 2048 lines
- • FFT input channel: CH1 or CH2
- • zoom function
- Transient recorder
- • timescale: 20ms/Div to 2000s/Div
- • max record time: 9.4hour/screen
- • automatic storage of data
- • automatic recording for more than 1 year • max. number of samples: 100/s
- • min. number of samples: 1 sample/20s
- Function generator
- • frequency range: sine from 0.5Hz to 1MHz
- • square and triangle from 0.5Hz to 500kHz
- • extended waveform library
- • amplitude range: 200mVpp to 8Vpp @ 1KHz//
- output impedance: 50ohm
- Oscilloscope
- • bandwidth: two channels DC to 12 MHz ±3dB • input impedance: 1 Mohm / 30pF
- • maximum input voltage: 30V (AC + DC)
- • time base: 0.1μs to 500ms per division
- • input range: 10mV to 3V/division
- • readouts: True RMS, dBV, dBm, p to p, Duty
- cycle, Frequency...
- • record length: 4K samples / channel
- • sampling frequency: 250Hz to 25MHz
- • sample history and digital grab function
- Bode plotter
- • Automated sync between oscilloscope and generator
- • Frequency range: 1kHz , 10kHz, 100kHz, 1MHz
- • Frequency start: 1Hz, 10Hz, 100Hz, 1kHz, 10kHz
|
|
Pocket size PC oscilloscope and function generator. This small box contains a world of measuring tools! |
 |
Q2112 |
|
- Resistance: 1Ω-2MΩ (±0.1Ω/1%)
- Capacitance: 0pF-10,000µF ( ±0.1pF/1.5%)
- Inductance: 0µH-10H ( ±0.1µH/1.5%)
- Peak test voltage (OC): -1.05V / +1.05V
- Peak test current (Silicon Chip Magazine): - 3.25mA / +3.25mA
- Test frequency accuracy: ±1%
- Sine purity: Typically -60dB 3rd harmonic
- Dimensions: 100 x 70 x 20mm
|
|
The Atlas LCR analyser is an advanced tester which greatly simplifies the testing of passive components. Simply connect the hook probes to the component legs and press test. In seconds the Atlas LCR will identify the type of component (inductor, cap |
 |
Q1340B NEW
|
|
- Single way to test plug crimping quality
- Wire tracing & cable mapping at the same time
- Easily locate the port with a flashing signal
- PoE switches & STP wire tracing up to 3KM
- Telephone line status/polarity indication
- Cable mapping & status indication up to 300M for continuity, shorts, opens and crossover
- Fast/slow scan function
- Display cable status and troubleshoot wiring
- Non- contact voltage detecting
|
|
This Noise-Filtering Network PoE Toner & Probe allows users to quickly locate and verify the cable status and troubleshoot wiring for continuity, shorts, opens and crossover on RJ45, Lan cable Cat5, 5e, 6 (UTP/STP), RJ11/12 telephone cable Cat. 3 (2/4/6 pin) & normal solid/stranded wire by alligator clips patch cord. |
 |
X7063 |
|
- Perpetual Calendar up to Year 2099
- Automatic calibration of network time service
- Day of week available to be selected in 8 languages
- Able to be used as an alarm with two daily alarms optional
- Automatic snooze function (OFF or 5~60min)
- Records temperature, humidity, wind speed and rainfall
- Display of ‘feels like temperature’, wind chill temperature, heat index, dew point temperature
- Future weather forecast and forecast temperature function
- Connects directly to Wi-Fi network (2.4Ghz only).
- Adjustable backlight (3 Levels) - when station is plugged in through USB output
|
|
This fantastic wireless Wi-Fi home weather station contains everything you require to monitor live weather conditions at home. The main base station displays at a glance, indoor and outdoor temperature, humidity, barometric pressure, recent rainfall, wind speed and direction. |
 |
Q2105 |
|
- Measure ESR (even in-circuit).
- Measure capacitance (from 0.3μF to 90,000μF).
- Automatically starts analysis when the ESR70 is connected.
- Audible alerts with different tones for various ESR levels.
- ESR resolution down to 0.01Ω.
- Polarity free due to bi-directional low voltage (500mV) test span.
- Low DC resistance checking measurement (even in-circuit).
- Supplied complete with 2mm male test leads and 2mm compatible gold plated crocs.
- Test leads are ultra-durable and 45cm (18") long with 2mm plugs.
- Enhanced software compensation of cable resistance.
- Enhanced compensation for leakage or parallel resistance.
- Improved LCD with better backlight.
- 10x faster capacitance measurement for large capacitors.
- Enhanced user options system.
- New triple-slope measurement system to vastly reduce the influence of parallel resistance and/or leakage current on capacitance measurements.
- Much wider capacitance measurement range now 0.3μF to 90,000μF (was 1μF to 22,000μF).
|
|
Measuring a capacitor's ESR (equivalent series resistance) is a great indicator of capacitor condition. The Atlas ESR offers instant results. Just connect the probes and press test - no need to worry about polarity! You can even use the Atlas ESR in circu |
 |
Q0967 NEW
|
|
- Auto/manual MPPT detection.
- Multiple protections - short circuit, reverse polarity, over voltage, over temperature, over current.
- No power supply required - no batteries.
- Large LCD with easy to read backlit display.
- Includes croc clip test cables, MC4 test cables and carry case.
|
|
Designed for measuring voltage, current and power of connected PV solar panels up to 800W. This meter provides instant feedback on PV system operation and allows optimal placement of solar panels for maximum energy conversion. |
 |
Q1347A |
|
- Test open, short or cross connection
- Measure length of telephone, network cabling up to 1000m
- Detect length with or without remote units connected
- 3% accuracy (±0.5m)
- Locate breakages
- Includes 8 remote units
- Includes carry case, 2 x 9V batteries, earphones, charging lead and adaptors
|
|
This comprehensive cable testing kit consists of three units. The main tester with 4 x 16 character screen, cable ‘sniffer’ receiving unit and 8 remote identifiers. |
 |
Q1264A
|
|
- Ranges: Lo: 30 - 80dB
- Hi: 80 - 130dB
- Resolution: ±0.1dB
- Freq. range: 31.5Hz - 8000Hz
- Dynamic range: 50dB
- Freq. weighting: A & C
- Accuracy: ±1.4dB
- Microphone: Electret condenser
- Dimensions: 252H x 66W x 33D mm
|
|
A must for the serious audio installer or enthusiast. This quality sound pressure level meter gives a digital readout of the ambient noise level at its microphone. Features two ranges: Low (30 to 80dB) and High (80 to 130dB), with two built-in weighting curves. A and C weighting. Response can be switched between slow (1s) or fast (125ms). Features |
 |
Q2100 |
|
- Connect any way round.
- Automatic component type identification.
- Automatic pinout identification.
- Transistor gain measurement.
- MOSFET gate threshold measurement.
- PN junction characteristics measurements.
- Leakage current measurement.
- Auto power on and power off.
- Ultra-slim and compact design.
|
|
An amazingly versatile piece of test equipment that could save you hours in looking up transistor, diode and FET specifications!
Once you've used the Atlas Component Analyser, you'll wonder how you ever did without it. |
 |
Q0968 |
|
- Two current ranges 4A, 80A
- 1mA resolution
- Backlit LCD
- One touch zero function
- 23mm jaw opening
- Auto power off
- Data hold function
- Test leads and carry case included
- 2x AAA battery included
- Cat III 600V
|
|
This compact clamp meter provides high resolution current readings up to 80A ac or dc. |
 |
Q2120 |
|
- A must have for vehicle servicing
- Suits lead acid batteries of all types including SLA and deep cycle
- Includes rubber holster
- No battery required
- Quick and accurate measurement of battery health.
|
|
Detects and analyses battery voltage, cold cranking amperes (CCA), resistance (mΩ) and battery cell condition. Suitable for use with cars, trucks, busses, boat, forklifts and motorcycles - anywhere a 12 Volt lead acid battery is used. Includes heavy duty wide entry croc clip cables. Very easy to use, simply connect to the battery, turn tester |
 |
Q2014 |
|
-
 100% developed, designed & assembled in Australia.
- Since 1976 Redback PA products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
-
|
|
Compact and portable, this handheld battery powered 1KHz tone generator has been designed to test PA systems and in particular hearing loop induction sound systems. The unit produces a 1KHz tone which is fed into the input of the amplifier under test. Two output levels are provided, 100mV and 1V. Includes 9V battery. Size: 79W x 117H x 24Dmm. |
 |
Q1344 |
|
- Cable length measurement, accurate to ±3%
- Short circuit, open, split pair detection
- UTP cable conductor verification
- Includes USB charging lead
- Internal lithium ion battery in main unit
- Bright display backlighting
- Auto power off
- Confirms integrity of patch leads and field wiring
- Suits RJ11 and RJ45 cabling
- Adjustable buzzer volume
|
|
This compact handheld cable verifier features a USB rechargeable lithiumion battery for easy recharge on the go. It verifies the length and integrity of coaxial and UTP data/telephone cabling. It's wiremap system detects short circuits, split pairs and cable length up to 350m. |
 |
D3012 NEW
|
|
- Continuity test for short circuit and open condition - shows pin configuration
- Cable length measurement up to 200m (±1.6m)
- Digital, analog and PoE testing modes
- 802.3af/at PoE port testing with pin detection
- Port flash and switch detail display
- Easy to read backlit graphical screen
- Non-contact AC voltage detection on receiver probe
|
|
A complete PoE cabling tester with cable tracer receiver, cable length testing,
|
 |
Q1300 NEW
|
|
- Adjustable alarms for high/low pressure, temperature
- Leak detection
- Temperature monitoring
- Solar powered dash display
- Sticky dash mount allows for mounting anywhere
- Includes 4 matched sensors, USB cable, valve stem nuts and fitment wrench
|
|
This wireless monitoring system displays tyre pressure and temperature for your vehicle or trailer. The wireless sensors screw onto the valve stems of your tyres and transmit back to the solar powered dash monitor. |
 |
Q1088 |
|
- True RMS AC measurement
- IP67 splash and dust-proof
- 4000 count LCD
- Autoranging
- MAX/MIN display modes
- Frequency counter to 40MHz
- Capacitance measurement
- Fused 10A input
- Temperature mode (°C/°F)
- Continuity and diode test
- Auto power off
- Low battery indicator
- 9V battery included
- Data hold & run mode
- Display backlight
- Class 2 double insulation
- Cat IV 600V, Cat III 1000V
|
|
Designed for marine, mining, industrial and outdoor environments, the unit is splash proof and fully sealed against dust ingress. |
 |
Q1242A |
|
- 200MΩ and 2000MΩ ranges
- Backlit LCD readout
- “Push to test” activation
- Auto power off
- Rubber holster
- Data hold
- High quality PVC leads
- Alligator clip lead adaptors
- Battery included
- Cat II 600V
|
|
Digital insulation testers measure the electrical insulation strength between two conductors by applying a high voltage across them and measuring any current that flows. This is to test for "leakage" paths and insulation breakdown in electrical circuits. |
 |
Q1341 |
|
- Headphone socket (earphones included)
- Adjustable buzzer volume
- Tests network and phone circuit voltage
- LED light on probe
- Single or dual tone
- Verifies short, open or crossed pairs in UTP cables
- Confirms integrity of patch leads and field wiring
- Includes RJ45 lead & croc clip test lead
|
|
Combines the functionality of a cable tracer and network cable tester in one convenient unit. The main unit can be connected to an unidentified pair which injects an audible signal down the line. |
 |
Q2022A NEW
|
|
- All metal construction
- Portable design runs off 9V battery (sold separately)
- Easy to use cable integrity checker for PA and AV installers
- New model supports Powercon and 3.5mm jacks
|
|
Compatible with 3.5mm jack, 6.35mm jack, 3/5/7/8 pin DIN, RCA, 3/5 pin XLR, 4P Speakon, Powercon, banana plugs, RJ45 and USB. A quick and easy way to confirm lead integrity. |
