Search Results | - Altronics

100% Australian

Established 1976

1-3 of 3

Refine

Category

Products

Brands

Sort

Categories 1Tools 2Projects

Products 3In Stock Only 1Not In Printed Catalogue

	Description	Downloads	Specs	Ordering
	50mL Jar Bare Conductive Paint T3133	Application Notes Material Safety Data Sheet Technical Datasheet	Dries at room temperature in 10-15 minutes Must be fully dry to work Easily removable with soap and water Seal with acrylic paint or spray varnish Can last years if treated properly and kept dry Works on: paper, cardboard, wood, plastic, glass, plaster, some rubbers, textiles, etc Connect batteries, LEDs and other components Great for attaching components and for PCB repair Can be used as a cold solder and wire paint Can be used with conductive thread and e-textiles Can be painted or sprayed over for protection or multi-layered circuitry Surface resistivity approximately 55 ohms/square at 50 microns layer thickness	ea $57.00 per ea Northbridge,WA Balcatta,WA Cannington,WA Midland,WA Myaree,WA Joondalup,WA Auburn,NSW Springvale,VIC Airport West,VIC Virginia,QLD Adelaide,SA Delivery In Stock Low - Call	Conductive paint is just like any other water-based paint, except that it conducts electricity! This means that you can paint wires or sensors directly onto almost any material around you, including paper, wood, plastic and glass.
	Arduino atmega32U4 Touch Board Z6435	Data Sheet - Touch Board vs Pi Cap Data Sheet - Touch Boards and shields Data Sheet - Touch Boards pin map Data Sheet	Microcontroller Atmel ATmega32U4 Touch IC Resurgent Semiconductor MPR121 MP3 decoder IC VLSI Solution VS1053b Audio output 15mW into 32Ω via 3.5mm stereo socket Removable storage up to 32GB via micro SD card Input voltage 3.0V DC – 5.5V DC Operating voltage 5V DC Max. output current (5V rail) 400mA (100mA at startup) Max. output current (3.3V rail) 300mA LiPo cell connector 2-way JST PH series - pin 1 +ve, pin 2 -ve LiPo charge current 200mA Capacitive touch electrodes 12 (of which 8 can be configured as digital I/O) Digital I/O Pins 20 (of which 3 are used for the MPR121 and 5 are used for the VS1053b — the latter can be unlinked via solder blobs) PWM channels 7 (shared with digital I/O pins) Analogue input channels 12 (shared with digital I/O pins) Flash memory 32 kB (ATmega32U4) of which 4kB used by boot loader SRAM 2.5kB (ATmega32U4) EEPROM 1kB (ATmega32U4) Clock speed 16MHz (ATmega32U4), 12.288MHz (VS1053b) DC current per I/O pin 40mA sink and source (ATmega32U4), 12mA source / 1.2mA sink (MPR121) Analogue input resistance 100MΩ typical (ATmega32U4)	ea $75.00 4+ $75.00 per ea Northbridge,WA Balcatta,WA Cannington,WA Midland,WA Myaree,WA Joondalup,WA Auburn,NSW Springvale,VIC Airport West,VIC Virginia,QLD Adelaide,SA Delivery In Stock Low - Call	The Touch Board is a microcontroller board with dedicated capacitive touch and MP3 decoder ICs. It has a headphone socket and micro SD card holder (for file storage), as well as having 12 capacitive touch electrodes. It is based around the ATmega32U4 and runs at 16MHz from 5V. It has a micro USB connector, a JST connector for an external lithium po
	Pi Cap Module to suit Raspberry Pi Z6430	Data Sheet - Pin Functions Data Sheet -Touch Board vs Pi Cap Data Sheet - Pi Cap + Raspberry Pi Data Sheet Instructions - How to make tutorials	Touch IC: Resurgent Semiconductor MPR121 Audio Output: 15mW into 32Ω via 3.5mm stereo socket Input Voltage: 3.3V (via 40-way Raspberry Pi GPIO connector) Input Current: 17mA idle, 36mA with all features in concurrent use. Capacitive Touch Electrodes: 12 (of which 8 can be configured as 3.3V digital I/O) Digital I/O Pins: 7, brought out from 40-way Raspberry Pi GPIO connector – pins 12, 13, 15, 16, 18, 22, 36 Push Switch: Active low momentary push switch connected to pin 7 on the 40-way Raspberry Pi GPIO connector (requires the Pi's onboard pull up resistor to be enabled in software) Active low, red connected to J8.31 (5mA when on), green to J8.29 (1mA when on), blue to J8.37 (4mA when on) Prototyping Area: 84 pads (7 x 12) with 1mm diameter drills spaced 2.54mm apart. Dimensions: 85 x 40 x 7mm	ea $39.00 4+ $39.00 per ea Northbridge,WA Balcatta,WA Cannington,WA Midland,WA Myaree,WA Joondalup,WA Auburn,NSW Springvale,VIC Airport West,VIC Virginia,QLD Adelaide,SA Delivery In Stock Low - Call	The Pi Cap is an addon board for the Raspberry Pi A+, B+, 2 B, 3 B and Zero. It features a dedicated capacitive sensing IC, 3.5mm stereo audio output, push switch, RGB LED and prototyping area