| Description | Downloads | Specs | Ordering | ||
|---|---|---|---|---|---|
 |
Fingerprint Access Controller KitK9350 |
|
| Do you hate carrying keys? The Fingerprint Access Controller can store and recognise up to 20 fingerprints and can give access to your home or workplace at any time, day or night. | |
 |
FTDI USB Breakout 3.3V / 5VZ6225 |
|
| FT232RL USB to serial 232 TTL adapter module with selectable 3.3V or 5V operation. On board TX/RX indicators. Works with offical and cloned Arduino boards. | |
 |
Funduino Ethernet Shield R3Z6242 |
| Allows an Arduino board to connect to the internet. It is based on the Wiznet W5100 ethernet chip providing a network (IP) stack capable of both TCP and UDP. Supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet via a stan | ||
 |
ATmega328P Vinyl Pinout Stickers - 5 PackZ9950 |
| Handy stickers for your Atmega328p chips. Great for reminding you of the appropriate pinouts for your DIY Arduino prototype. Printed on quality Arlon UV vinyl. | ||
 |
Light Interrupt Sensor Breakout BoardZ6326 |
| Operating Voltage: DC 3-5V Single-channel signal output. Mounting holes for easy fixed installation. Output switch circuit board can be connected directly to microcontroller IO port. | ||
 |
Case to suit Z6404 Hifiberry AMP+H6406 |
| High quality 3mm black plexiglass case to house your Raspberry Pi and your Amp+ module. | ||
 |
Programmable Remote Control Mains Switch KitK6130 |
| This remote control mains switch can be programmed to switch appliances on and off after a set period or to switch power on and off at set times. | ||
 |
Salt Water Fuel Cell Motorcycle KitK1111 |
|
| An environmentally friendly motorcycle powered by a salt water fuel cell. A great way to learn about alternative energy ideas. No batteries required! Includes 3 fuel cell sheets. Approx length 130mm. Can be assembled in under an hour. | |
 |
200 In 1 Electronics Lab KitK2209 |
|
| Learn about the fundamentals of electronics in a safe environment. This electronics lab lets kids learn about transistors, diodes, capacitors, oscillators, electronic circuits and schematic symbols. A must have for the engineer of tomorrow! A huge array of fun projects to build with the comprehensive easy to read manual and included parts. Require | |
 |
60 In 1 Electronics Lab KitK2206 |
| These simple kits are a great introduction to the world of electronics. Basic principles are covered and assembly is completely solderless using a series of spring loaded terminals. | ||
 |
Mixed Prototyping Wire Pack 60pcsP1017 |
| Multi-colour reusable leads for prototyping and working with development shields. Includes pin to pin (male to male) and pin to socket (male to female) types. 60 pieces. | ||
 |
Male to Male Prototyping Wire Pack 65pcsP1016 |
| Multi-colour reusable leads for prototyping and working with development shields. Pin to pin (male to male) type. 65 pieces. | ||
 |
Funduino Pro Mini 328 5V/16MHzZ6222A |
|
| Measuring a tiny (0.8mm) thick the Arduino Pro Mini comes unpopulated enabling you to solder in any connector or wire with any orientation you need. Ideal for experienced Arduino users or building into a compact embedded design. This board connects directly to the FTDI basic breakout board and supports auto-reset. | |
 |
Funduino 5V DC Stepper Motor And ULN2003 C...Z6330 |
|
| Diameter: 28mm Voltage: 5V Step angle: 5.625 x 1 / 64 Reduction ratio: 1 / 64 5 Line 4 phase can be driven by ULN2003 chip. Dimensions of Board : 31 × 35mm ULN2003 Darlington using high-power stepper motor driver chip A, B, C, D four-phase LED indicates the status of the stepper motor work | |
 |
Funduino ULN2003 Motor Drive Module For Ar...Z6329 |
| On-board ULN2003A chipset 5-12V power supply On-board 4-way indicator light On-board XH-5P socket Compatible with Arduino | ||
 |
Temperature and Humidity Sensor Breakout f...Z6320 |
|
| Voltage: 5V Temperature: -40~80''C, +/0.5 Humidity: 20~90%RH +/-2%RH Suitable for Arduino SCM A product for Arduino that works with official Arduino boards. | |
 |
GT-511C1R Fingerprint Sensor Breakout ModuleZ6394 |
| Add fingerprint authentication to your access control project. This device can store up to 20 individual prints via 360° recognition. | ||
 |
Funduino MP3 Module With MicrophoneZ6335 |
| Supports audio decoding formats: MP3, MP3 + V, WMA, WAV, MIDI, SP-MIDI Separate analog, digital and IO power supply; serial data and control interface (SPI) Headphones and audio output interface, with internal PLL clock frequency multiplier; quality stereo digital to analog converter (DAC); 16 bits Scalable on-chip analog to digital converter (AD | ||
 |
ADXL345 3 Axis Accelerometer Breakout For ...Z6321 |
|
| The ADXL345 is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit twos complement and is accessible through either a SPI (3- or 4-wire) or I2C digital interface. | |
 |
DS1302 Real Time Clock ModuleZ6207 |
|
| The DS1302 trickle-charge timekeeping chip contains a real-time clock/calendar and 31 bytes of static RAM. It communicates with a microprocessor via a simple serial interface. The real-time clock/calendar provides seconds, minutes, hours, day, date, month, and year information. The end of the month date is automatically adjusted for months with few | |
 |
4 Channel 5V Relay Control Board Module/Sh...Z6327 |
| This is a 5V 4-Channel Relay interface board, Be able to control various appliances, and other equipments equipment with large current. It can be controlled directly by Micro-controller (Raspberry Pi, Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic). 5V 4-Channel Relay interface board, and each one needs 15-20mA Driver Current Equiped | ||
 |
5V Relay Control Board Module/ShieldZ6325 |
| This 5V relay module is suitable for integration with many types of micro control systems, including Arduino. Ideal for home appliance control. 5V-12V TIL control signal suitable for controlling DC / AC signal. The module is perfect for common Arduino applications. - Suitable for SCM development, home appliance control - 5V-12V TTL control sign | ||
 |
4WD Robot Builders Motorised BaseK1092 |
| Available in either 2WD or 4WD configuration this robotic vehicle chassis features individual motors for each wheel, fitted with encoding wheels for integration with control sensors. It&rsquos the ideal base for your own Arduino powered robo-car design. | ||
 |
2WD Robot Builders Motorised BaseK1090 |
| Available in either 2WD or 4WD configuration this robotic vehicle chassis features individual motors for each wheel, fitted with encoding wheels for integration with control sensors. It&rsquos the ideal base for your own Arduino powered robo-car design. | ||
 |
Funduino Starter Kit For ArduinoZ6310 |
| A parts kit for people interested in learning working with Arduino powered designs. It includes an Arduino UNO compatible board, proto-shield, dot matrix LED module, 7 segment displays, two breadboards, stepper motor, servo, IR remote, connection leads, battery box and a variety of components, LEDs, buttons and sensors. |
