|
Description |
Downloads |
Specs |
Ordering |
|
 |
Z6319 NEW
|
|
- Large 3-digit display of measured temperature
- Operates in both a heating and cooling mode of operation
- Programmable settings for temp set point, temp hysteresis, compressor delay and temperature calibration.
- Waterproof NTC temperature sensor has -50 to +99.9°C measurement range with ±1°C accuracy
- Over temperature and sensor failure audible and visual alarm
- Unit temperature reading can be calibrated
- Relays switch up to 120/240VAC @ 10A or 15VDC @ 10A
- 12VDC module operation
|
|
The STC-1000 temperature controller is a self contained heating / cooling controller that operates on 12VDC and controls either AC or DC loads up to 10A max current. |
 |
ZA6421 NEW
|
|
- Ultra compact form factor
- Dual core ARM Cortex M0+ processor
- Two SPI controllers
- Two I2C controllers
- 16 PWM channels
- 26 multifunction GPIO pins
- Three analogue inputs
- On board USB controller
- In-built temperature sensor
- Castellated module allows soldering direct to carrier boards
- Drag-and-drop programming using mass storage over USB
- Low-power sleep and dormant modes
- Accurate on-chip clock
- Accelerated integer and floating-point libraries on-chip
|
|
Raspberry Pi Pico is a tiny, fast, and versatile board built using RP2350, a brand new microcontroller chip designed by Raspberry Pi in the UK. From controlling appliances to operating a light display, Raspberry Pi Pico puts the technology that underpins countless everyday operations into your hands. |
 |
Z6440B NEW
|
|
- On board speaker
- MEMs Microphone with LED indicator
- Touch sensitive logo
- Built-in sleep/off mode that means the board can be powered-down with batteries connected
- Discrete regulator that can supply up to 190mA of current to external accessories
- 25 Programmable LEDs in a 5 x 5 grid
- 3-axis motion sensing
- On-board magnetometer
- On-board temperature sensor
- On-board light level sensing
- 2 x programmable buttons, A & B
- BLE Bluetooth 5.0
- 2.4Ghz Micro:bit Radio
- Rear-mounted push button
- Power off (push and hold power button)
- 25 pins
- MEMS microphone and LED indicator
- Onboard speaker
- Touch-sensitive logo pin
- LED power indicator
- C++, MakeCode, Python, Scratch
|
|
The Micro:bit go kit is easy to code with, all you need is your web browser and a micro USB cable and you are ready to start all kinds of exciting STEM/STEAM experiments, no need for any extra software to be installed. Kit includes USB cable, batteries and battery holder. |
 |
Z6318 NEW
|
|
- GPS Breakout Module
- 2.7V-3.6V Supply
- Interfaces; UART, USB, SPI, DDC
- RT Crystal
- Antenna Supply and supervisor
- 3 Configuration Pairs
- 1 Timepulse pair
- External Interrupt/Wakeup
|
|
The NEO-6 module is a stand-alone GPS receiver featuring a high performance u-blox 6 positioning engine. |
 |
Z6317 NEW
|
|
- 3-digit display of temperature
- Module can operate in a heating or cooling mode of operation
- Multiple parameters can be set such as temp trip point, hysteresis and delay.
- Waterproof NTC temperature sensor has -30 to +110°C measurement range with 0.1°C accuracy
- Relay switches up to 120VAC @ 10A or 14VDC @ 10A
- 12V module operation
|
|
This high precision temperature control module is a highly functional self-contained temperature controller module for both heating and cooling applications. |
 |
Z6316 NEW
|
|
- Easy to set up and pair - Android or iOS eWeLink app available for direct control.
- Onboard Bluetooth status indicator and relay indicator.
- With 2 optocoupler isolation, strong anti-interference ability.
- Onboard N76E003/STM8S003 and SPP-C Bluetooth 2.1 module.
- Compact board design.
- Module with diode effusion protection short response time
|
|
A combined relay and control board with the ability to switch on and off connected loads using an App on your phone via Bluetooth. The eWeLink app offers seamless power switching using your device when in range of the relay board (typically 10m). |
 |
J0085 NEW
|
|
- Sensor Type: Hall effect
- Working Voltage: 5 to 18V DC (min tested working voltage 4.5V)
- Max current draw: 15mA @ 5V
- Output Type: 5V TTL
- Working Flow Rate: 1 to 30 Litres/Minute
- Working Temperature range: -25 to +80℃
- Working Humidity Range: 35%-80% RH
- Accuracy: ±10%
- Maximum water pressure: 2.0 MPa
- Output duty cycle: 50% +-10%
- Output rise time: 0.04us
- Output fall time: 0.18us
- Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min)
- Pulses per Litre: 450
- Durability: minimum 300,000 cycles
- Cable length: 150mm
- 1/2″ nominal pipe connections, 0.78″ outer diameter, 1/2″ of thread
- Size: 63.5 x 35.5 x 35.5mm
|
|
The YF-S201 Hall Effect Water Flow Meter Sensor comes with three wires: red (5-24VDC power), black (ground) and yellow (Hall effect pulse output). |
 |
J0083 NEW
|
|
|
|
This 5mm tubing is made of silicone rubber which is flexible, resistant to high temperatures and does not deteriorate outdoors. |
 |
J0080 NEW
|
|
- Working Temperature: 0℃ - 40 ℃
- Motor voltage: 12VDC
- Motor current: 200-300mA
- Flow Rate : >80ml/min
- Tube Size : 5mm tube
- Pump Head Material : ABS
- Pump Pipe : Transparent silicone pipe
- Pulsations : Three roller
|
|
This 12V Peristaltic Water Dosing Pump can be used in a variety of applications. |
 |
Z6240A NEW
|
|
- Form factor compatible with earlier series of Arduino boards for compatibility with existing shields and projects.
- Expanded memory and faster clock speed
- Extra on-board peripherals including 12-bit DAC, CAN BUS and OP Amp.
- Wider input voltage range for integration with motors, LED strips and actuators.
- SWD connector for debugging.
- HID support for keystrokes and mouse movement.
|
|
Introducing the Funduino UNO R4 Minima compatible Arduino board. Equipped with the RA4M1 microprocessor, this board offers enhanced processing power, expanded memory, and more, all while maintaining the reliable UNO form factor and practical 5V operating voltage. Get ready for a remarkable upgrade! |
 |
ZW6240A NEW
|
|
- Form factor compatible with earlier series of Arduino boards for compatibility with existing shields and projects.
- Expanded memory and faster clock speed
- Extra on-board peripherals including 12-bit DAC, CAN BUS and OP Amp.
- Wider input voltage range for integration with motors, LED strips and actuators.
- HID support for keystrokes and mouse movement.
- Wi-FI and Bluetooth connectivity on board.
- Qwiic connector for I2C compatible sensors and actuators.
- LED matrix on board.
- Supports battery powered RTC.
|
|
The Funduino UNO R4 with WiFi is an Arduino compatible board integrating the powerful RA4M1 microcontroller with the robust wireless capabilities of the ESP32-S3 from Espressif. Additionally, it features an on-board 12x8 LED matrix, a Qwiic connector, a VRTC, and an OFF pin, making it an ideal choice for all your maker projects. |
 |
A0713 NEW
|
|
- Operating voltage: 12 - 15 V/DC
- Current consumption: approx. 20 mA / 80 mA (relay off / on)
- Adjustable time: approx. 2 sec. to 23 min., (± 30 %)
- Connection: via flat-pin plug at the module
- LED: 2 (1 x LED operating voltage, 1 x LED relay “ON”)
- Relay point: 1 x ON, max. 3A, max 25V
- Dimensions: approx. 87 x 60 x 33 mm (with flanges)
|
|
Avoid the hassle with this pre-assembled timing controller, conveniently packaged in a compact and reliable form. It's easy to connect and versatile enough to adapt to your requirements. The start and stop functions are managed by simple switching contacts, and the relay output can control devices up to 25VDC at 3A. |
 |
H8960A NEW
|
|
- Great for better heat dissipation on the Pi 5.
- Access to all Pi Ports: Power, Video, Audio, USB, LAN, MicroSD Card.
- Compatible with the Raspberry Pi 5.
- Includes cooling fan with header connection.
- Includes 3 heatsinks.
|
|
An all metal Raspberry Pi 5 case with internal cooling fan and heatsinks. |
 |
H8958A NEW
|
|
- Great for better heat dissipation on the Pi 5.
- Access to all Pi Ports: Power, Video, Audio, USB, LAN, MicroSD Card.
- Slots for camera cables and GPIO access.
- Compatible with the Raspberry Pi 5.
- Includes cooling fan with header connection.
- Integral heatsink for added cooling efficiency.
|
|
This compact multi-layer acrylic case suits the Raspberry Pi 5 and provides access to all ports on the board. Includes cooling fan module with heatsink. |
 |
Z6379X |
|
|
|
Detects soil humidity levels - a handy little sensor for building automated watering and retic systems. 3.3-5V input. Note: typical lifespan of about a year when left in soil permanently. 58L x 20Wmm. |
 |
Z6434 NEW
|
|
- RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom
- Dual-core Arm Cortex M0+ processor, flexible clock running up to 133 MHz
- 264KB of SRAM, and 2MB of on-board Flash memory
- USB-C connector, keeps it up to date, easier to use
- The castellated module allows soldering directly to carrier boards
- USB 1.1 with device and host support
- Low-power sleep and dormant modes
- Drag-and-drop programming using mass storage over USB
- 29 × multi-function GPIO pins (20× via edge pinout, others via solder points)
- 2 × SPI, 2 × I2C, 2 × UART, 4 × 12-bit ADC, 16 × controllable PWM channels
- Accurate clock and timer on-chip
- Temperature sensor
- Accelerated floating-point libraries on-chip
- 8 × Programmable I/O (PIO) state machines for custom peripheral support
|
|
The RP2040-Zero, is a low-cost, high-performance Pico-like MCU board based on Raspberry Pi RP2040 microcontroller. 29 × multi-function GPIO pins. Configurable pin function, allows flexible development and integration. |
 |
Z6338X |
|
- Input Range: 3.8V to 32V.
- Output Range: 1.25V to 35V.
- Input Current: 3A (max),
- No-Load Current: 18mA (5V input, 8V output*)
- *No-load current is less than 18mA. Higher the voltage, the greater the no load current.
|
|
A converter module allowing a low input voltage to be increased to a higher output voltage. Input 3.8-32V DC. Output 1.25-35V DC. Ideal for powering higher voltage devices from a typical 5V microcontroller platform. 3A continuous current. |
 |
K8300A |
|
- Power: 5V DC 2A
- Nozzle Diameter: 0.6mm
- Pen Dimension: 18.5 x2.9 x 4.3cm
- Heating Temperature: 185-210C
- Materials Filament: Suitable for 1.75mm PLA and ABS
- Moulding Speed: Adjustable (3 levels)
|
|
A crafty addition to any work space this handheld pen extrudes 1.75mm PLA or ABS filament for decorating objects, simple plastic repair jobs or touch ups to 3D printed models. |
 |
J0070A NEW
|
|
- Step Angle: 1.8Deg
- Temperature Rise: 80DegC max
- Ambient Temperature: -20DegC~+50DegC
- Insulation Resistance: 100 MOhm Min. ,500VDC
- Dielectric Strength: 500VAC for 1minute
- Shaft Radial Play: 0.02Max. (450g-load)
- Shaft Axial Play: 0.08Max. (450g-load)
- Max. radial force: 28N (20mm from the flange)
- Max. axial force: 10N
- Product description: 42 two-phase stepping motor Body length 34mm Static torque 2.2kg.cm
- 5mm shaft diameter with flat wire, length 24mm,
- Wiring method: black green A +, A-. Red blue B +, B-,
- Adapter driver JK0220 (driving voltage DC12V ~ 36V, AC12V ~ 24V, current range 0.3A ~ 2.0A)
|
|
12V 200-step 1.8° 48BYG stepper motor with interface
lead. 2 phase type. 0.23Nm holding torque. 5mmØ
shaft. NEMA17 M3 mounting hole pattern (31mm).
Size: 42x42x34 (25mm shaft). 1m lead. |
 |
Z6315A NEW
|
|
|
|
A handy parts kit containing everything you need to start learning Arduino and building projects. Includes a huge selection of sensor boards, LEDs, pots, jumper wires, a breadboard, LCD screen and much more! |
 |
Z6588 NEW
|
|
- A great guide to get you started with Raspberry Pi, Pico, or Micro:bit
- Backup power provided by a Supercapacitor - no batteries required!
- Tracks year, month, day, weekday, hour, minutes, seconds
- Schedule events or alarms
- Automatically switches between main power and backup power
- High accuracy clock - within 30 seconds per year
- PiicoDev Connector, compatible with Qwiic and STEMMA QT (3.3V Only)
|
COMING SOONThis item is arriving soon. |
The PiicoDev Precision Temperature Sensor features a low-power, high precision TMP117 with 16-bit resolution and an accuracy of ±0.1°C (across -20°C to +50°C) with no calibration required. |
 |
SA0915 NEW
|
|
- Switch Type: SPST microswitch
- Connection: 6.3mm spade
- Illumination: 5-12V input
- Max material thickness: 30mm
- Mounting Hole: 27.5mm
- Mounting depth: 61mm
|
|
Ideal for use in retro gaming projects or anywhere a jumbo momentary switch may be required. |
 |
SA0914 NEW
|
|
- Switch Type: SPST microswitch
- Connection: 6.3mm spade
- Illumination: 5-12V input
- Max material thickness: 30mm
- Mounting Hole: 27.5mm
- Mounting depth: 61mm
|
|
Ideal for use in retro gaming projects or anywhere a jumbo momentary switch may be required. |
 |
SA0913 NEW
|
|
- Switch Type: SPST microswitch
- Connection: 6.3mm spade
- Illumination: 5-12V input
- Max material thickness: 30mm
- Mounting Hole: 27.5mm
- Mounting depth: 61mm
|
|
Ideal for use in retro gaming projects or anywhere a jumbo momentary switch may be required. |
 |
SA0912 NEW
|
|
- Switch Type: SPST microswitch
- Connection: 6.3mm spade
- Illumination: 5-12V input
- Max material thickness: 30mm
- Mounting Hole: 27.5mm
- Mounting depth: 61mm
|
|
Ideal for use in retro gaming projects or anywhere a jumbo momentary switch may be required. |
