|
Description |
Downloads |
Specs |
Ordering |
|
 |
A2691B NEW
|
|
- 2 x 100W RMS output power @ 4 Ohm
- FM Stereo tuner
- Bluetooth 5.0 Wireless input
- 30 FM station presets
- 4 stereo RCA inputs
- Tape input/output
- A-B speaker switch
- Remote control
|
|
A stylish 2 x 100W (into 4 Ohm) FM stereo receiver with bluetooth audio streaming and a remote control. It features four stereo RCA inputs for CD, DVD, TV and Auxiliary. The large rotary dial controls volume, balance, bass and treble. |
 |
A4370A |
|
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 70V, 100V and 4-16Ω outputs
- 240V AC or 24V DC operation
- 24V DC @ 1 Amp output for external devices
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicators
- Fault Indicators
- Power Status Indicators
- Rack Mountable (suits 19 inch racks)
|
|
This range of booster amplifiers are ideal for installations requiring high power zone amplifiers. Simply choose a power rating according to the wattage required for each zone. |
 |
A4116 |
|
- 15W RMS per channel
- 1 music input (3.5mm)
- 1 auxiliary input
- 4-16Ω output
- 240V ac operation
- Includes Power Supply
|
|
Packed with features, this super compact stereo amp is ideally suited to classrooms, boardrooms, boutiques, reception areas or anywhere a small functional stereo system is required. Designed in close consultation with several leading AV installation compa |
 |
A4017 |
|
- To mount any of the Redback half rack products into a 19" wide racking system, the H 4990 bracket is required. If a single product is mounted into the H 4990, then a metal (H 4992) or plastic (H 4993) infill panel can be fitted for a neater finish.
|
|
Super compact with surprising performance specifications, intended for smaller PA system applications. Our engineering team based the design around a National TDA1519 monolithic IC achieving virtually "destruction proof" operation under quite severe misuse |
 |
A4376 |
|
|
|
1 Pair of bolt on rack ears to allow installation of amplifiers into a 19" rack system. Designed to fit the following Redback models:
A 4375, A 4385, A 4375A, A 4385A, A 4377, A 4387, A 4210, A 4212. |
 |
A4312 |
|
- 85% efficient class-D power performance.
- Low power consumption & heat generation.
- Compact 1RU case housing two individual amplifiers.
- Individual dedicated protection circuitry.
- Individual cooling systems for each channel.
- LED indicators for signal, peak, protection and power.
- Constant 100V floating output per channel (ie no reference to earth).
- Compatible with Altronics line monitoring equipment.
- 24V DC battery backup power (per channel).
- 240V AC operation.
- Remote control on/off switching function.
- In-built bandpass filter for 80Hz and 16KHz signals.
- Built-in short circuit, overload, high temperature protection.
- 2 year warranty
|
|
Excellent for multizone public address paging and background music systems! Engineered to meet the growing demands of venues such as RSL clubs, taverns, hotels, conference & function centres enabling individual program sources to play to different rooms |
 |
A4860 |
|
- Class-D 2 x 50W amplifier
- Bluetooth 4.2 wireless streaming
- Stereo RCA & 3.5mm jack inputs
- Optical input with high performance DAC
- Automatic signal switching with priority for Bluetooth audio source
- 240V AC operation
|
|
A compact bluetooth stereo amplifier for home and commercial sound systems. Features a high spec Class-D 2x50W RMS amplifier and optical input for connection to digital audio sources. Pairs well with the A4861 200W subwoofer amplifer. |
 |
A4861 |
|
- 200W into 4 ohms
- Stereo RCA input
- Speaker level input and outputs
- Adjustable phase and crossover frequency
- Volume level control
- 240V AC operation
|
|
A compact dedicated subwoofer amplifier providing up to 200W into 4 ohms. Ideally paired with the A 4860 and C 1065 ceiling subwoofer, but is also suitable for any passive subwoofer. Ideal for integration with commercial systems in fashion boutiques, shopping centres, gymnasiums etc. Front panel provides level control, phase adjustment and crossov |
 |
A4380A |
|
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 70V, 100V and 4-16Ω outputs
- 240V AC or 24V DC operation
- 24V DC @ 1 Amp output for external devices
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicators
- Fault Indicators
- Power Status Indicators
- Rack Mountable (suits 19 inch racks)
|
|
This range of booster amplifiers are ideal for installations requiring high power zone amplifiers. Simply choose a power rating according to the wattage required for each zone. |
 |
A4212 |
|
- Designed to meet AS60118.4-2007
- Coverage up to 650m2
- XLR line & mic inputs
- Aux input via stereo RCA
- EWIS signal connection (RCA)
- Short circuit proof
- Compressor for added speech intelligibility
- Adjustable VOX sensitivity
- Compatible with single loop designs
|
|
Hearing induction loop amplifiers are installed to greatly enhance the listening experience of people using hearing aids. They are commonly installed in public areas which are generally noisy, making it difficult for hearing impaired users to hear clearly. |
 |
A1117 NEW
|
|
- Compact Class D stereo 2 x 15W (into 4Ω)
- Bluetooth 5.1 connectivity
- Upgrade your favourite speakers to Bluetooth wireless
- Includes mains power supply
- Excellent range and audio clarity
- Suitable for in-ceiling mounting
- Assignable bluetooth device name and password
|
|
This Bluetooth mini amplifier is a great way to add wireless connectivity to a new or existing pair of ceiling or wall speakers that aren't Bluetooth equipped. It offers Bluetooth 5.1 connectivity for excellent device range and audio performance, coupled with an efficient Class-D amplifier. |
 |
A1116 |
|
|
|
This 2x25W RMS amplifier module with Bluetooth receiver sticks to your speaker magnet and connects to a pair of in-ceiling/in-wall speakers. Easy to install and works with Bluetooth enabled devices such as smartphones, tablets and laptops. Includes 15V power supply. |
 |
A4022A NEW
|
|
- Balanced microphone input
- Built in VOX muting circuit
- Stereo line inputs
- Bass and treble tone controls
- 240V AC operation
|
|
Designed to meet the requirements of small to medium sized professional public address installations, delivering an output power of 30W RMS. |
 |
A4205 |
|
- Designed to meet AS60118.4-2007
- Suits small booths 2-3 square metres
- XLR mic input
- Compatible with single loop designs
- Aux input via stereo RCA
- 10 year warranty
- Australian designed & assembled
- Short circuit proof
- Compressor circuitry
|
|
This compact hearing loop amplifier is designed for use in information kiosks, ticketing booths, help desks etc. Anywhere a small loop system is required to aid the hearing impaired. Engineered to meet AS60118.4-2007. A balanced mic input and stereo line auxiliary input is provided. Compact half rack 1RU case. 24V DC operation. |
 |
A4199 |
|
- Amplifier type: Class D stereo
- Output power: 15W RMS per channel @ 4 ohm
- Distortion: 0.06%
- Headphone output: 105mW RMS per channel
- Headphone distortion: 0.05%
- Min load: 4Ω
- Current draw: 9A max.
- Power: 12V DC
- Dimensions: 285W x 128D x 43Hmm
- Weight: 0.8kg
|
|
Ideal for small businesses or simple multi-zone home audio systems. Switch between up to 4 different audio sources - connect up to 8 speakers. Toslink digital audio input for TV audio. Great for background music use. Also fitted with 6.35mm microphone connection. |
 |
A4310 |
|
- 85% efficient class-D power performance.
- Low power consumption & heat generation.
- Compact 1RU case housing four individual amplifiers.
- Individual dedicated protection circuitry.
- Individual cooling systems for each channel.
- LED indicators for signal, peak, protection and power.
- Constant 100V floating output per channel (ie no reference to earth).
- Compatible with Altronics line monitoring equipment.
- 24V DC battery backup power.
- 240V AC operation.
- Remote control on/off switching function.
- In-built bandpass filter for 80Hz and 16KHz signals.
- Built-in short circuit, overload, high temperature protection.
- 2 year warranty
|
|
Excellent for multizone public address paging and background music systems! Engineered to meet the growing demands of venues such as RSL clubs, taverns, hotels, conference & function centres enabling individual program sources to play to different rooms |
 |
A4314 |
|
- 85% efficient class-D power performance.
- Low power consumption & heat generation.
- Compact 1RU case housing four individual amplifiers.
- Individual dedicated protection circuitry.
- Individual cooling systems for each channel.
- LED indicators for signal, peak, protection and power.
- Constant 100V floating output per channel (ie no reference to earth).
- Compatible with Altronics line monitoring equipment.
- 24V DC battery backup power (per channel).
- 240V AC operation.
- In-built bandpass filter for 80Hz and 16KHz signals.
- Built-in short circuit, overload, high temperature protection.
- 2 year warranty
|
|
Excellent for multizone public address paging and background music systems! Engineered to meet the growing demands of venues such as RSL clubs, taverns, hotels, conference & function centres enabling individual program sources to play to different rooms |
 |
A4198 |
|
- Amplifier type: Class D stereo
- Output power: 15W RMS per channel @ 4 ohm
- Distortion: 0.06%
- Headphone output: 105mW RMS per channel
- Headphone distortion: 0.05%
- Min load: 4Ω
- Current draw: 9A max.
- Power: 12V dc
- Dimensions: 205W x 108D x 26Hmm
- Weight: 0.5kg
|
|
Excellent for multi-room audio distribution, this 12V powered four zone amplifier produces 30W RMS per zone (15W RMS per channel) - all from a case just 200mm across! One input source may be connected on the front panel via stereo RCA sockets. |
 |
A4395A |
|
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 70V, 100V and 4-16Ω outputs
- 240V AC or 24V DC operation
- 24V DC @ 1 Amp output for external devices
- 300mA battery trickle charge
- Adjustable input level sensitivities
- Bass and Treble controls
- Phantom power on microphone input (XLR Input 1)
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicators
- Fault Indicators
- Power Status Indicators
- Rack Mountable (suits 19 inch racks)
|
|
The Redback A 4395 is a 500 Watt Mixer amplifier for installations requiring a high power zone amplifier. Ideally suited for use in shopping centres, pedestrian precincts, public transport facilities and convention centres. |
 |
A4390A |
|
- Multi-stage thermally cued fan cooling
- Input signal presence indicator
- Output peak limited
- 2U 19" rack mount (ears included)
- 3 pin XLR input, 3 pin XLR loop out
- Level control rear mounted
- 100V, 70V and 4 - 16Ω outputs
- Thermal and overload protection
- 240V AC, or 24V DC operation
- 300mA 24V battery trickle charge
|
|
This booster is ideal for installations requiring a high power zone amplifier. Ideal for use in shopping centres, pedestrian precincts, public transport facilities and convention centres. |
 |
A4201 |
|
- SPECIFCATIONS:
- Power Output: 50 Watts RMS x 2 into 8 ohm
- Total Harmonic Distortion: <0.01% @30W; <5.0% @50W
- Minimum Speaker Impedance: 6 ohm
- Signal-to-Noise Ratio: 103 dB, A weighted
- Input Impedance: 2k ohm ± 5%
- Frequency response: 20-20,000 Hz
- Channel Separation: 95 dB
- Efficiency: 85%
- Dynamic Range: >100 dB
- Electrical Requirement: 24V DC @ 5A centre pin positive
- Dimensions: 50H x 86W x 143D mm
- Weight: 455g
- BLUETOOTH SPECIFICATIONS:
- Bluetooth version: BT V5.0
- Analog input sensitivity: 1-2V RMS
- Bluetooth range: 30m (line of sight)
- Decoding: SBC, MP3, AAC
- Output: A2DP, AVRCP
|
|
A compact, sturdy 2x50W RMS class-D stereo amplifier with 3.5mm input on the front and RCA input on the back for easy connection. |
 |
A4210 |
|
- Designed to meet AS60118.4-2007
- Coverage up to 180m2
- XLR line & mic inputs
- Aux input via stereo RCA
- EWIS signal connection (RCA)
- Short circuit proof
- Compressor for added speech intelligibility
- Adjustable VOX sensitivity
- Compatible with single loop designs
|
|
Hearing induction loop amplifiers are installed to greatly enhance the listening experience of people using hearing aids. They are commonly installed in public areas which are generally noisy, making it difficult for hearing impaired users to hear clearly. |
 |
A4573 |
|
 Designed & manufactured in Australia.
- Since 1976 Redback public address products have been manufactured in Perth, Western Australia by Altronics. With over 40 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. Read more about our Australian Made products
|
|
Optional Plugin Board to suit the Phase 4 range of Redback Amplifiers. It generates pre chime, bell, alert and evacuation tones. The alert tone can function continuously, or switch to evac tone after a preset time delay (adjustable 30 seconds to 4.5 minu |
 |
A4344A |
|
- Digital AM/FM RDS tuner with 24 presets 18 x FM and 6 x AM
- USB File player with Autoplay and Autosearch functions
|
|
A plug-in AM/FM tuner module to suit all JDM public address amplifiers. |
 |
A4260B NEW
|
|
- Mixer amplifier with in-built SD/USB/FM tuner/Bluetooth music source
- 85% efficient class-D power performance
- Low power consumption & heat generation
- Compact 1RU case
- Bass & treble control
- Front panel mic input
- Protection circuitry
- LED indicators for signal, peak, protection and power
- Selectable 100V line/4-16Ω output
- Mic/Line/Phantom Power options on Mic 1-4
- 24V DC battery backup power input
- Emergency priority input (Mic 1)
- Adjustable VOX muting
|
|
This compact Class-D design amplifier offers multi source mixing plus USB/SD card/FM tuner audio playback and Bluetooth streaming functionality. |
 |
A4262B NEW
|
|
- Mixer amplifier with in-built SD/USB/FM tuner/Bluetooth music source
- 85% efficient class-D power performance
- Low power consumption & heat generation
- Compact 1RU case
- Bass & treble control
- Front panel mic input
- Protection circuitry
- LED indicators for signal, peak, protection and power
- Selectable 100V line/4-16Ω output
- Mic/Line/Phantom Power options on Mic 1-4
- 24V DC battery backup power input
- Emergency priority input (Mic 1)
- Adjustable VOX muting
|
|
These compact Class-D design amplifiers offer multi source mixing plus USB/SD card/FM tuner audio playback and Bluetooth streaming functionality. |
 |
A4250A |
|
- Compact 1RU 19” rack mount design
- Balanced mic or line input
- 100V line output
- Phantom power
- Overload limiting
- Over voltage limiting
- On demand fan cooling (60W and 100W versions only)
- Over temperature shut down protection
- Dual input connectors
- Variable input sensitivities
- 240V AC / 24V DC operation
- Australian designed & manufactured
|
|
These compact 1RU rack mount amplifiers are suitable for both stand alone PA system use, or as zone amplifiers in larger systems requiring local inputs. All models operate on 240V ac or 24V dc for battery backup operation. |
 |
A4230A |
|
- Compact 1RU 19” rack mount design
- Balanced mic or line input
- 100V line output
- Phantom power
- Overload limiting
- Over voltage limiting
- On demand fan cooling (60W and 100W versions only)
- Over temperature shut down protection
- Dual input connectors
- Variable input sensitivities
- 240V ac / 24V dc operation
- Australian designed & manufactured
|
|
Utilising only 1RU of rack space, this range of Redback power amplifiers is available in three power ratings of 30W, 60W and 100W RMS. They lend themselves perfectly for installations requiring individual zone amplifiers. |
 |
A4255A |
|
- Compact 1RU 19” rack mount design
- Balanced mic or line input
- 100V line output
- VOX muting
- Phantom power
- Four auxiliary inputs
- 3.5mm Jack Input (Front Mounted)
- Overload limiting
- Over voltage limiting
- On demand fan cooling (60W and 100W versions only)
- Over temperature shut down protection
- Dual input connectors
- Variable input sensitivities
- 240V AC / 24V DC operation
- Australian designed & manufactured
|
|
These compact 1RU rack mount amplifiers are suitable for both stand alone PA system use, or as zone amplifiers in larger systems requiring local inputs. All models operate on 240V ac or 24V dc for battery backup operation. |
 |
A4235 |
|
- Compact 1RU 19” rack mount design
- Balanced mic or line input
- 100V line output
- VOX muting
- Phantom power
- Four auxiliary inputs
- Overload limiting
- Over voltage limiting
- On demand fan cooling
- Over temperature shut down protection
- Dual input connectors
- Variable input sensitivities
- 240V ac / 24V dc operation
|
|
These compact 1RU rack mount amplifiers are suitable for both stand alone PA system use, or as zone amplifiers in larger systems requiring local inputs. All models operate on 240V ac or 24V dc for battery backup operation.
All models include a choice of |
 |
A4235A |
|
- Compact 1RU 19” rack mount design
- Balanced mic or line input
- 100V line output
- VOX muting
- Phantom power
- Four auxiliary inputs
- Overload limiting
- Over voltage limiting
- On demand fan cooling
- Over temperature shut down protection
- Dual input connectors
- Variable input sensitivities
- 240V ac / 24V dc operation
|
|
This compact 30W 1RU rack mount amplifiers is suitable for both stand alone PA system use, or as zone amplifiers in larger systems requiring local inputs. Operates on 240V ac or 24V dc for battery backup operation. |
 |
A4245A |
|
- Compact 1RU 19” rack mount design
- Balanced mic or line input
- 100V line output
- VOX muting
- Phantom power
- Four auxiliary inputs
- 3.5mm Jack Input (Front Mounted)
- Overload limiting
- Over voltage limiting
- On demand fan cooling (60W and 100W versions only)
- Over temperature shut down protection
- Dual input connectors
- Variable input sensitivities
- 240V AC / 24V DC operation
- Australian designed & manufactured
|
|
These compact 1RU rack mount amplifiers are suitable for both stand alone PA system use, or as zone amplifiers in larger systems requiring local inputs. All models operate on 240V ac or 24V dc for battery backup operation. |
 |
A4373 |
|
- Maximum volume setting
- Minimum volume setting
- Australian designed and assembled
|
|
When fitted and used in conjunction with A 2280B wallplate to provide remote volume level adjustment. Ideal for situations where the amplifier is located in a remote rack. Plugs into the amplifier internally on the main board. |
 |
A3043 |
|
- Amplifier type: Class D stereo
- Output power: 15W RMS per channel @ 4 ohm
- Distortion: 0.06%
- Microphone pre-amp gain: 40dB
- Min load: 4ohm
- Current draw: 2A max.
- Power: 12V dc
- Dimensions: 92.6L x 73.4W x 26.6H mm
- Weight: 160g
|
|
This compact amplifier is a great way to power a pair of speakers without the bulk of a full size hi-fi receiver. It provides 2x15W RMS output power - enough to power a pair of small ceiling or bookshelf speakers. |
 |
A4209 |
|
|
|
Pack of 5 indicator labels to inform patrons that there is a hearing aid induction loop installed. 140H x 100W mm |
 |
A2711 |
|
- Output level: 500mV(800mV volume max.)
- Playback frequency: 20Hz - 19KHz
- THD: <0.3%
- Signal to noise ratio: >65dB
- File types: MP3/WMA/WAV
- MP3/WMA decoder: 32-320kbps decoding
- WAV decoder:
- PCM single track 128-768kbps
- PCM double track 256-1536kbps
- IMA-ADPCM single track 32-192kbps
- IMA-ADPCM double track 64-384kbps
- Storage: USB/SD Card (maximum 32GB - FAT16/32)
- Supply voltage: 12V DC (10-15V operating range)
- Power consumption: <2W
- Dimensions: 120W x 56.5D x 22H mm
|
|
Optional Plugin Board to suit the A4275 and A4285 mixer amplifiers. Enables audio playback of MP3 files from USB stick and SD memory cards. |
 |
A1932A |
|
- Powered by nominal 24V DC
- 100V line audio output
- Line level audio input - 600mV
- Short circuit, overload, and thermal cutout protection
- Bolt-in chassis construction
- Australian designed and assembled
|
|
This module is designed for use in emergency evacuation systems and is powered by an external 24V DC source. It accepts a line level audio input and produces a 100V line output via a transformer. |
 |
A1937 |
|
- Powered by 24V DC
- 100V line audio output
- Line level audio input
- Short circuit, overload and thermal cutout protection
- Bolt-in chassis construction
|
|
These modules are designed for use in emergency evacuation systems and are powered by an external 24V DC source. They accept a line level audio input and produce a 100V line output via a transformer. The modules feature short circuit, overload and therm |
|
A1922 |
|
- Powered by 24V DC
- 100V line audio output
- Line level audio input
- Short circuit, overload and thermal cutout protection
- Bolt-in chassis construction
|
|
These modules are designed for use in emergency evacuation systems and are powered by an external 24V DC source. They accept a line level audio input and produce a 100V line output via a transformer. The modules feature short circuit, overload and thermal cutout protection, and are constructed on a steel chassis.
|
 |
A4155 |
|
- Output Power (Stereo 8Ω): 150W + 150W
- TA 1KHz THD≤1% (4Ω): 220W + 220W
- Bridge 8Ω: 440W
- Frequency Response: 20Hz-20KHz +/-0.5dB
- Input Sensitivity: 0.77V
- Maximum input level: 18dB/6.2V
- Input Impedance active balanced: 20KOHMS/Balanced, 10KOHMS/un-Balanced
- Signal/noise ration a-weighted RMS: ≥95dB
- Crosstalk at rated output power (8Ω 1kHz): >70dB
- Damping Factor (f=1kHz 8Ω): >240
- Slew rate internal: 15V/us
- Protection: Short circuit, current limited DC fault AC line fuse, thermal cut off, power up/down transients
- Indicators: POWER (BLUE) PROT (RED) CLIP (YELLOW) BR (GREEN) PAR (GREEN)
- Cooling: Variable Speed Fan
- Front Panel Controls: LEVEL ACH, BCH POWER SWITCH
- Rear Panel Controls: STEREO/BRIDGE/PARALLEL MODE SWITCH
- Connector: XLR BALANCED INPUT, PROFESSIONAL SPEAKON OUTPUT
- Power consumption half power 8Ω: <440W
- Power Supply: 240V AC/50Hz
- Interior Dimensions: 482 x 325.5 x 88mm
- Exterior Dimensions: 555 x 415 x 168mm
- Net Weight: 8.5kg
- Gross Weight: 10.5kg
|
|
The Apple series Biema power amplifiers are a cost effective solution for demanding commercial audio applications. These non-bridgeable models are designed to be used as standard 2 channel or stereo amplifiers. The design incorporates a fan forced cooling sys |
 |
A4157 |
|
- Output Power (Stereo 8Ω): 250W + 250W
- TA 1KHz THD≤1% (4Ω): 370W + 370W
- Bridge 8Ω: 740W
- Frequency Response: 20Hz-20KHz +/-0.5dB
- Input Sensitivity: 0.77V
- Maximum input level: 18dB/6.2V
- Input Impedance active balanced: 20KOHMS/Balanced, 10KOHMS/un-Balanced
- Signal/noise ration a-weighted RMS: ≥95dB
- Crosstalk at rated output power (8Ω 1kHz): >70dB
- Damping Factor (f=1kHz 8Ω): >240
- Slew rate internal: 15V/us
- Protection: Short circuit, current limited DC fault AC line fuse, thermal cut off, power up/down transients
- Indicators: POWER (BLUE) PROT (RED) CLIP (YELLOW) BR (GREEN) PAR (GREEN)
- Cooling: Variable Speed Fan
- Front Panel Controls: LEVEL ACH, BCH POWER SWITCH
- Rear Panel Controls: STEREO/BRIDGE/PARALLEL MODE SWITCH
- Connector: XLR BALANCED INPUT, PROFESSIONAL SPEAKON OUTPUT
- Power consumption half power 8Ω: <740W
- Power Supply: 240V AC/50Hz
- Interior Dimensions: 482 x 325.5 x 88mm
- Exterior Dimensions: 555 x 415 x 168mm
- Net Weight: 9kg
- Gross Weight: 10kg
|
|
The Apple series Biema power amplifiers are a cost effective solution for demanding commercial audio applications. These non-bridgeable models are designed to be used as standard 2 channel or stereo amplifiers. The design incorporates a fan forced cooling sys |
 |
A4159 |
|
- Output Power (Stereo 8Ω): 350W + 350W
- TA 1KHz THD≤1% (4Ω): 500W + 500W
- Bridge 8Ω: 1000W
- Frequency Response: 20Hz-20KHz +/-0.5dB
- Input Sensitivity: 0.77V
- Maximum input level: 18dB/6.2V
- Input Impedance active balanced: 20KOHMS/Balanced, 10KOHMS/un-Balanced
- Signal/noise ration a-weighted RMS: ≥95dB
- Crosstalk at rated output power (8Ω 1kHz): >70dB
- Damping Factor (f=1kHz 8Ω): >240
- Slew rate internal: 15V/us
- Protection: Short circuit, current limited DC fault AC line fuse, thermal cut off, power up/down transients
- Indicators: POWER (BLUE) PROT (RED) CLIP (YELLOW) BR (GREEN) PAR (GREEN)
- Cooling: Variable Speed Fan
- Front Panel Controls: LEVEL ACH, BCH POWER SWITCH
- Rear Panel Controls: STEREO/BRIDGE/PARALLEL MODE SWITCH
- Connector: XLR BALANCED INPUT, PROFESSIONAL SPEAKON OUTPUT
- Power consumption half power 8Ω: <440W
- Power Supply: 240V AC/50Hz
- Interior Dimensions: 482 x 325.5 x 88mm
- Exterior Dimensions: 555 x 415 x 168mm
- Net Weight: 9.5kg
- Gross Weight: 11.5kg
|
|
The Apple series Biema power amplifiers are a cost effective solution for demanding commercial audio applications. These non-bridgeable models are designed to be used as standard 2 channel or stereo amplifiers. The design incorporates a fan forced cooling sys |
 |
A4173 |
|
- Rugged heavy duty construction
- 19” rack mount
- Bridgeable, parallel or two channel stereo operation
- Earth lift switch
- 3 pin XLR and 6.35mm inputs.
- Short circuit protection with indicator
- Overload protection with indicator
- Clipping prevention circuitry with indicator
- Variable speed fan forced cooling
- Muting circuit for switch on/off
|
|
This range is designed to function as a stereo or high power single channel amplifier for use in foreground sound reinforcement ie: pubs, clubs, cinemas and multi-function venues. |
 |
A4173A |
|
- Rugged heavy duty construction
- 19” rack mount
- Bridgeable, parallel or two channel stereo operation
- Earth lift switch
- 3 pin XLR inputs.
- Short circuit protection with indicator
- Overload protection with indicator
- Clipping prevention circuitry with indicator
- Variable speed fan forced cooling
- Muting circuit for switch on/off
|
|
This new series dubbed the "Apple" range have been completely redesigned by Biema to offer vastly improved cooling, efficiency and circuit protection. This range is designed to function as a stereo or high power single channel amplifier for use in foreground sound reinforcement ie: pubs, clubs, cinemas and multi-function venues. |
 |
A4322 |
|
- 5 inputs
- 4 output zones
- 70V or 100V output
- 4Ω or 8Ω output
- 24V DC operation
- Over temperature, over current and short circuit protection
- LED VU meter
- 2 year warranty
- Telephone paging input
- Chime and siren
|
|
An economical solution for smaller installations including offices, workshops, smaller shopping arcades, schools etc. |
 |
A4324 |
|
- 5 inputs
- 4 output zones
- 70V or 100V output
- 4Ω or 8Ω output
- 24V DC operation
- Over temperature, over current and short circuit protection
- LED VU meter
- 2 year warranty
- Telephone paging input
- Chime and siren
|
|
An economical solution for smaller installations including offices, workshops, smaller shopping arcades, schools etc. |
 |
A4320 |
|
- 5 inputs
- 4 output zones
- 70V or 100V output
- 4Ω or 8Ω output
- 24V DC operation
- Over temperature, over current and short circuit protection
- LED VU meter
- 2 year warranty
- Telephone paging input
- Chime and siren
|
|
An economical solution for smaller installations including offices, workshops, smaller shopping arcades, schools etc. |
 |
A4330 |
|
- 5 inputs
- 6 output zones
- Direct 100V line output
- 4Ω output
- Individual zone attenuators (max 20W)
- 24V DC operation
- LED VU meter
- 2 year warranty
- Volume, treble and bass controls for each input
- Over current protection
- Over temperature protection
- Short circuit protection
- Telephone paging input
- Phantom power
- Selectable microphone priority
|
|
Housed in a heavy duty 3RU rack mount cabinet, these mixer amplifiers include a host of features and are ideally suited for schools, offices, medical suites, office/factory units etc. |
 |
A4332 |
|
- 5 inputs
- 6 output zones
- Direct 100V line output
- 4Ω output
- Individual zone attenuators (max 40W)
- 24V DC operation
- LED VU meter
- 2 year warranty
- Volume, treble and bass controls for each input
- Over current protection
- Over temperature protection
- Short circuit protection
- Telephone paging input
- Phantom power
- Selectable microphone priority
|
|
Housed in a heavy duty 3RU rack mount cabinet, these mixer amplifiers include a host of features and are ideally suited for schools, offices, medical suites, office/factory units etc. |
 |
A4336 |
|
- 5 inputs
- 6 output zones
- Direct 100V line output
- 4Ω output
- Individual zone attenuators (max 80W)
- 24V DC operation
- LED VU meter
- 2 year warranty
- Volume, treble and bass controls for each input
- Over current protection
- Over temperature protection
- Short circuit protection
- Telephone paging input
- Phantom power
- Selectable microphone priority
|
|
Housed in a heavy duty 3RU rack mount cabinet, these mixer amplifiers include a host of features and are ideally suited for schools, offices, medical suites, office/factory units etc. |
 |
A4047 |
|
- 3 balanced microphone inputs
- Phantom power on mic inputs
- 3 line inputs
- 19” rack mount kit included
- VOX muting
- Tape output RCA sockets
- Bass and treble tone controls
- 100V line output
- 240V AC or 24V DC operation
- Built in short circuit protection
- 10 year warranty
- Optional evac module available
- Optional remote volume module
- Australian designed & assembled
|
|
Designed to meet the requirements of medium sized professional public address installations, delivering an output power of 100W RMS respectively. |
 |
A4037 |
|
- 3 balanced microphone inputs
- Phantom power on mic inputs
- 3 line inputs
- 19” rack mount kit included
- VOX muting
- Tape output RCA sockets
- Bass and treble tone controls
- 100V line output (note: this model cannot be converted to 70V line as per others in the series)
- 240V AC or 24V DC operation
- Built in short circuit protection
- 10 year warranty
- Optional evac module available
- Optional remote volume module
- Australian designed & assembled
|
|
Designed to meet the requirements of medium sized professional public address installations, delivering an output power of 40W RMS respectively. |
 |
A4043 |
|
- 3 balanced microphone inputs
- Phantom power on mic inputs
- 3 line inputs
- 19” rack mount kit included
- VOX muting
- Tape output RCA sockets
- Bass and treble tone controls
- 100V line output
- 240V AC or 24V DC operation
- Built in short circuit protection
- 10 year warranty
- Optional evac module available
- Optional remote volume module
- Australian designed & assembled
|
|
Designed to meet the requirements of medium sized professional public address installations, delivering an output power of 100W RMS respectively. |
 |
A4372 |
|
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 100V outputs
- 240V AC or 24V DC operation
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicators
- Fault Indicators
- Power Status Indicators
- Rack Mountable (suits 19 inch racks)
|
|
Consists of 2 x 125 Watt amplifiers in a single chassis. Ideal for multi-zone 100V PA requirements. Manufactured in Australia to stringent engineering criteria, the Phase 5 amplifier series exhibit quite remarkable performance and outstanding reliability. |
 |
A4275C |
|
- Very low noise and distortion
- Thermal overload protection
- Thermally cued forced fan cooling
- Protect Mode
- 4 levels of priority/Vox muting
- LCD display of amplifier status
- Minimum and Maximum Master Volume Over-ride
- Minimum and Maximum Remote Volume Over-ride
- USB keyboard interface for labelling of inputs and installer contact details. • 6 inputs configurable as balanced microphone or line
- Music Input on front panel
- Adjustable line level sensitivity
- 70V, 100V and 4-16ohm outputs
- 240V AC or 24V DC operation
- 300mA Backup Battery charging
- Phantom power (on microphone inputs)
- Tape out (Dual RCA)
- Pre-amp send and return connections (RCA)
- Balanced line output (3 pin male XLR)
- Remote Volume option
- 24V switched output via PTT microphone (not supplied)
- 19” Rack Mount (2 unit).
- Optional Alert/Evac tones with voice-over message (via A 4573 module)
- Optional MP3 input with remote control (via A 2711 module)
|
|
Engineered for professional PA installations, the A 4275C conservatively delivers 125W RMS power. Including three levels of input priority, bass and treble controls and phantom powering capability enable unparalleled flexibility for a wide scope of applications such as schools, shopping centres, workshops, mine sites and office buildings. |
 |
A4285C |
|
- VU meter on LCD screen
- Output peak limited
- Multi-stage thermally cued fan cooling
- 2U 19" rack mount
- Tape record out terminals
- Remote volume facility
- Optional alert, evac & chime tone generator (A 4573)
- Vox activated 24V dc output
- 6 inputs with 3 pin XLR or 2 x RCA sockets
- Phantom powering available on all inputs
- Three levels of priority
- Option for mic/line to operate vox muting on inputs 1 to 3
- Push to talk (PTT) terminals on rear panel
- Bass and treble tone controls
- Power amp line out connector
- Terminals for 100V line, 70V line and 4 - 16Ω loads
- 240V ac or 24V dc power operation
- Thermal & fuse overload protection
- Built in short circuit protection
- 300mA trickle charge facility for 24V dc batteries
- Master volume can be configured as pre or post line out
|
|
Engineered for professional PA installations, the A 4285B conservatively delivers 250W RMS power. Including three levels of input priority, bass and treble controls and phantom powering capability enable unparalleled flexibility for a wide scope of applications such as schools, shopping centres, workshops, mine sites and office buildings. |
 |
A4270 |
|
- Multi-stage thermally cued fan cooling
- 2U 19” rack mount (with optional A 4376)
- Tape record out terminals
- Provision for connection to Redback A4660 touchscreen paging console
- MP3 based Alert/Evac tones with MP3 voice over message for emergency tones (built in)
- 3 mic input and 4 auxiliary inputs
- Phantom powering available on all inputs
- Adjustable vox muting on inputs 1 & 2.
- Bass and treble tone controls
- Terminals for 100V line output
- 240V AC or 24V DC power operation
- Thermal & fuse overload protection
- Built in short circuit protection
- Australian designed & assembled
|
|
Similar in functionality to the recently released A 4377/A4387 amplifiers with the addition of four 100V line output zones. |
 |
A4280 |
|
- Multi-stage thermally cued fan cooling
- 2U 19” rack mount (with optional A 4376)
- Tape record out terminals
- Provision for connection to Redback A4660 touchscreen paging console
- MP3 based Alert/Evac tones with MP3 voice over message for emergency tones (built in)
- 3 mic input and 4 auxiliary inputs
- Phantom powering available on all inputs
- Adjustable vox muting on inputs 1 & 2.
- Bass and treble tone controls
- Terminals for 100V line output
- 240V AC or 24V DC power operation
- Thermal & fuse overload protection
- Built in short circuit protection
- Australian designed & assembled
|
|
Similar in functionality to the recently released A 4377/A4387 amplifiers with the addition of four 100V line output zones. |
 |
A4377A |
|
- 3 Balanced microphone inputs / 3 Aux inputs / 1 Music input
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 100V standard with optional 70V and 4-16Ω outputs
- 240V AC or 24V DC operation
- VOX muting on inputs 1 and 2 (Switch selectable internally)
- Adjustable VOX level sensitivities
- Bass and Treble controls
- Tape Output
- Phantom power on microphone inputs (DIP switch selectable internally)
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicator
- Half power mode when overdriven
- Fault Indicators
- 24V DC Power Status Indicator
- Optional Alert/Evac module with voice over message for emergency tones (A 4573)
- Optional remote volume (With A 4373 Digital volume control module fitted and external A 2280B wall plate)
- Rack Mountable (suits 19 inch racks) with optional A 4376 rack ears
|
|
This 125 Watt 4 channel mixer amplifier is specifically designed for applications requiring up to three microphone inputs, without compromising output power and overall performance. The amplifier feature three inputs which can be configured for either microphone or line level operation. |
 |
A4379 |
|
- 6 Balanced microphone inputs / 6 Aux inputs / 1 Music input
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 100V standard with optional 70V and 4-16Ω outputs
- 240V AC or 24V DC operation
- VOX muting on inputs 1 and 2 (Switch selectable internally)
- Adjustable VOX level sensitivities
- Bass and Treble controls
- Tape Output
- Phantom power on microphone inputs (DIP switch selectable internally)
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicator
- Half power mode when overdriven
- Fault Indicators
- 24V DC Power Status Indicator
- Optional Alert/Evac module with voice over message for emergency tones (A 4573)
- Optional remote volume (With A 4373 Digital volume control module fitted and external A 2280B wall plate)
- Rack Mountable (suits 19 inch racks) with optional A 4376 rack ears
|
|
Designed for applications requiring up to six microphone inputs, without compromising output power and overall performance. Each model features inputs which can be configured for either microphone or line level operation. |
 |
A4387A |
|
- 3 Balanced microphone inputs / 3 Aux inputs / 1 Music input
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 100V standard with optional 70V and 4-16Ω outputs
- 240V AC or 24V DC operation
- VOX muting on inputs 1 and 2 (Switch selectable internally)
- Adjustable VOX level sensitivities
- Bass and Treble controls
- Tape Output
- Phantom power on microphone inputs (DIP switch selectable internally)
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicator
- Half power mode when overdriven
- Fault Indicators
- 24V DC Power Status Indicator
- Optional Alert/Evac module with voice over message for emergency tones (A 4573)
- Optional remote volume (With A 4373 Digital volume control module fitted and external A 2280B wall plate)
- Rack Mountable (suits 19 inch racks) with optional A 4376 rack ears
|
|
This 250 Watt 4 channel mixer amplifier is specifically designed for applications requiring up to three microphone inputs, without compromising output power and overall performance. The amplifier feature three inputs which can be configured for either microphone or line level operation. |
 |
A4389 NEW
|
|
- 6 Balanced microphone inputs / 6 Aux inputs / 1 Music input
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 100V standard with optional 70V and 4-16Ω outputs
- 240V AC or 24V DC operation
- VOX muting on inputs 1 and 2 (Switch selectable internally)
- Adjustable VOX level sensitivities
- Bass and Treble controls
- Tape Output
- Phantom power on microphone inputs (DIP switch selectable internally)
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicator
- Half power mode when overdriven
- Fault Indicators
- 24V DC Power Status Indicator
- Optional Alert/Evac module with voice over message for emergency tones (A 4573)
- Optional remote volume (With A 4373 Digital volume control module fitted and external A 2280B wall plate)
- Rack Mountable (suits 19 inch racks) with optional A 4376 rack ears
|
|
Designed for applications requiring up to six microphone inputs, without compromising output power and overall performance. Each model features inputs which can be configured for either microphone or line level operation. |
 |
A2777D |
|
- 5.2-channel 80 Watt surround sound with Dolby TrueHD and DTS-HD
- 4K120AB and 8K60B HDMI (with future update) with HDCP 2.3 and eARC (4 in/1 out)
- Dolby Vision™, Hybrid Log-Gamma and BT.2020
- Supports enhanced media and gaming - ALLM, VRR, QFT, QMS (with future update)
- Wi-Fi®, AirPlay 2®, Spotify Connect and Voice Control
- MusicCast multi-room audio app control
- Pandora®, Spotify, Amazon Music, SiriusXM, TIDAL, Deezer, iHeartRadio and more
- YPAO automatic room calibration
- MusicCast Surround-capable: add optional MusicCast speakers to provide wireless surrounds for a 5.1-channel setup
|
|
5.2 channel AV receiver with CINEMA DSP 3D, HDMI 4-in/1-out, wireless surround.Movie watchers are catered for with 4K Ultra HD as well as HDMI 2.0, BT.2020 compatibility and HDCP 2.2, HDR video. 80W RMS per channel. Four HDMI inputs. Wireless rear speaker capability. |
 |
A2776C |
|
- Bluetooth compatible for wireless music streaming This AV receiver is equipped with Bluetooth functionality to let you enjoy easy wireless music playback from smartphones and other devices. Yamaha Compressed Music Enhancer is now optimised for Bluetooth audio transmission to ensure that your music will have vivid, lively sound quality even during wireless playback.
- 4K Ultra HD full support with 4K60p, HDCP2.2 This AV receiver completely supports with the latest HDMI standards. Thanks to transmission of 4K video at 60 frames per second pass-through, you can fully enjoy the high definition video quality of 4K without degradation. It also adheres to the HDCP2.2 copyright protection standard for 4K video transmission.
- HDMI with 3D and Audio Return Channel 3D means the receiver can handle 3D signal data. The Audio Return Channel function enables data to be sent and received via the same HDMI cable, so you can hear the sound from the TV via a single HDMI cable, with no need for an extra optical cable.
- Discrete amp configuration for high sound quality This AV receiver was designed with a strong focus on achieving exceptionally high sound clarity. It employs a discrete amp configuration and a low jitter PLL circuit, which contribute to its excellent audio performance.
- AV setup guide app makes system setup easier AV Setup Guide is an app that makes it much easier to perform receiver setup, and also assists you with cable connections between the AV receiver and source devices. It guides you through various settings such as speaker connections, TV and source device connections and power amp assignment. System illustrations and actual AV receiver images help you understand how to make the connections between devices, for much quicker system setup. It is available in multiple languages. Designed for iOS and Android tablet.
- SCENE for one-touch start Pressing a SCENE button powers on the AV Receiver and selects the input source and DSP mode. You can re-set the buttons for different sources by selecting a source and DSP mode, then pressing a SCENE button for more than three seconds.
- HDMI CEC for easy operation Another benefit of HDMI is the availability of CEC functionality. When the unit is connected to a CEC compatible TV, it will turn on and off together with the TV, and you can use the TV remote to control the volume. CEC also provides advanced functionality with other components. For example, you can use the receiver’s remote unit to control player functions like Skip and Stop. NOTE: All connected devices must be HDMI CEC compatible. Some CEC compatible TVs / players may not work.
- YPAO sound optimisation for automatic speaker setup YPAO analyses the room acoustics and adjusts various audio parameters for optimum sound in just a few minutes. It’s like having a professional installer calibrate your system.
- HD audio with CINEMA DSP Yamaha’s exclusive CINEMA DSP technology supports playback of HD Audio (Dolby TrueHD, DTS-HD Master Audio, etc.), providing natural and expansive sound imaging.
- Virtual CINEMA FRONT provides irtual 5-channel surround sound with high quality and resolution Even when it is impossible to install surround speakers behind the listening position, Virtual CINEMA DSP reproduces virtual 5-channel surround sound filled with realism, with only two front speakers. With Virtual CINEMA FRONT, you will enjoy virtual 5-channel surround sound with higher quality and resolution by installing surround speakers at the front. You get more flexibility to arrange your speakers inside the room, along with easy enjoyment of high quality surround sound.
- Extra Bass provides rich bass reproduction, even with small speakers Yamaha’ s exclusive low-range enhancement technology delivers richer bass than you expect from the speaker size while maintaining good localisation and sound balance even with compact front speakers. When a subwoofer is used, it improves the volume of the entire low range of the speaker system, not only the front speakers, but also enhancing the bass from the subwoofer. You'll enjoy video and music with sound that has exceptional power and presence.
- Compressed Music Enhancer When music is encoded into a digitally compressed format like MP3, the frequency response suffers. Yamaha’s Compressed Music Enhancer employs sophisticated digital signal processing using exclusive algorithms to restore what was lost, so the music always sounds the way it should.
- Subwoofer Trim for improved sound imaging The Subwoofer Trim control enhances the low frequencies by avoiding overlap with the front speaker output. This will result in a cleaner, more focused sound stage while providing a seamless frequency response. When subwoofer frequency overlap occurs in conventional systems, the overall sound is “pushed” toward the subwoofer. Subwoofer Trim takes care of this by separating the low subwoofer frequencies cleanly, thus stabilising the front stage while providing a well-balanced enhanced bass sound.
- ECO mode lowers power consumption by 20%* Yamaha’s new ECO mode reduces power consumption by about 20%. It can be set from the top of the GUI menu. NOTE: Compared to power consumption when ECO mode is off (Yamaha measurement).
- Selectable auto power standby Auto Power Standby lets you save energy by selecting to turn off the power after 20 minutes, 2, 4, 8 or 12 hours.
|
|
The all-new RX-V385 model is wireless-enabled, with streaming from Bluetooth devices at the touch of a button. Movie watchers are also catered for with 4K Ultra HD as well as HDMI 2.0, BT.2020 compatibility and HDCP 2.2, HDR video. 70W RMS per channel. Four HDMI inputs. AM/FM analog tuner. |
