|
Description |
Downloads |
Specs |
Ordering |
|
 |
A4860 |
|
- Class-D 2 x 50W amplifier
- Bluetooth 4.2 wireless streaming
- Stereo RCA & 3.5mm jack inputs
- Optical input with high performance DAC
- Automatic signal switching with priority for Bluetooth audio source
- 240V AC operation
|
|
A compact bluetooth stereo amplifier for home and commercial sound systems. Features a high spec Class-D 2x50W RMS amplifier and optical input for connection to digital audio sources. Pairs well with the A4861 200W subwoofer amplifer. |
 |
A4201 |
|
- SPECIFCATIONS:
- Power Output: 50 Watts RMS x 2 into 8 ohm
- Total Harmonic Distortion: <0.01% @30W; <5.0% @50W
- Minimum Speaker Impedance: 6 ohm
- Signal-to-Noise Ratio: 103 dB, A weighted
- Input Impedance: 2k ohm ± 5%
- Frequency response: 20-20,000 Hz
- Channel Separation: 95 dB
- Efficiency: 85%
- Dynamic Range: >100 dB
- Electrical Requirement: 24V DC @ 5A centre pin positive
- Dimensions: 50H x 86W x 143D mm
- Weight: 455g
- BLUETOOTH SPECIFICATIONS:
- Bluetooth version: BT V5.0
- Analog input sensitivity: 1-2V RMS
- Bluetooth range: 30m (line of sight)
- Decoding: SBC, MP3, AAC
- Output: A2DP, AVRCP
|
|
A compact, sturdy 2x50W RMS class-D stereo amplifier with 3.5mm input on the front and RCA input on the back for easy connection. |
 |
A4047 |
|
- 3 balanced microphone inputs
- Phantom power on mic inputs
- 3 line inputs
- 19” rack mount kit included
- VOX muting
- Tape output RCA sockets
- Bass and treble tone controls
- 100V line output
- 240V AC or 24V DC operation
- Built in short circuit protection
- 10 year warranty
- Optional evac module available
- Optional remote volume module
- Australian designed & assembled
|
|
Designed to meet the requirements of medium sized professional public address installations, delivering an output power of 100W RMS respectively. |
 |
A4280 |
|
- Multi-stage thermally cued fan cooling
- 2U 19” rack mount (with optional A 4376)
- Tape record out terminals
- Provision for connection to Redback A4660 touchscreen paging console
- MP3 based Alert/Evac tones with MP3 voice over message for emergency tones (built in)
- 3 mic input and 4 auxiliary inputs
- Phantom powering available on all inputs
- Adjustable vox muting on inputs 1 & 2.
- Bass and treble tone controls
- Terminals for 100V line output
- 240V AC or 24V DC power operation
- Thermal & fuse overload protection
- Built in short circuit protection
- Australian designed & assembled
|
|
Similar in functionality to the recently released A 4377/A4387 amplifiers with the addition of four 100V line output zones. |
 |
A3043 |
|
- Amplifier type: Class D stereo
- Output power: 15W RMS per channel @ 4 ohm
- Distortion: 0.06%
- Microphone pre-amp gain: 40dB
- Min load: 4ohm
- Current draw: 2A max.
- Power: 12V dc
- Dimensions: 92.6L x 73.4W x 26.6H mm
- Weight: 160g
|
|
This compact amplifier is a great way to power a pair of speakers without the bulk of a full size hi-fi receiver. It provides 2x15W RMS output power - enough to power a pair of small ceiling or bookshelf speakers. |
 |
A4043 |
|
- 3 balanced microphone inputs
- Phantom power on mic inputs
- 3 line inputs
- 19” rack mount kit included
- VOX muting
- Tape output RCA sockets
- Bass and treble tone controls
- 100V line output
- 240V AC or 24V DC operation
- Built in short circuit protection
- 10 year warranty
- Optional evac module available
- Optional remote volume module
- Australian designed & assembled
|
|
Designed to meet the requirements of medium sized professional public address installations, delivering an output power of 100W RMS respectively. |
 |
A4861 |
|
- 200W into 4 ohms
- Stereo RCA input
- Speaker level input and outputs
- Adjustable phase and crossover frequency
- Volume level control
- 240V AC operation
|
|
A compact dedicated subwoofer amplifier providing up to 200W into 4 ohms. Ideally paired with the A 4860 and C 1065 ceiling subwoofer, but is also suitable for any passive subwoofer. Ideal for integration with commercial systems in fashion boutiques, shopping centres, gymnasiums etc. Front panel provides level control, phase adjustment and crossov |
 |
A4270 |
|
- Multi-stage thermally cued fan cooling
- 2U 19” rack mount (with optional A 4376)
- Tape record out terminals
- Provision for connection to Redback A4660 touchscreen paging console
- MP3 based Alert/Evac tones with MP3 voice over message for emergency tones (built in)
- 3 mic input and 4 auxiliary inputs
- Phantom powering available on all inputs
- Adjustable vox muting on inputs 1 & 2.
- Bass and treble tone controls
- Terminals for 100V line output
- 240V AC or 24V DC power operation
- Thermal & fuse overload protection
- Built in short circuit protection
- Australian designed & assembled
|
|
Similar in functionality to the recently released A 4377/A4387 amplifiers with the addition of four 100V line output zones. |
 |
A4387A |
|
- 3 Balanced microphone inputs / 3 Aux inputs / 1 Music input
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 100V standard with optional 70V and 4-16Ω outputs
- 240V AC or 24V DC operation
- VOX muting on inputs 1 and 2 (Switch selectable internally)
- Adjustable VOX level sensitivities
- Bass and Treble controls
- Tape Output
- Phantom power on microphone inputs (DIP switch selectable internally)
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicator
- Half power mode when overdriven
- Fault Indicators
- 24V DC Power Status Indicator
- Optional Alert/Evac module with voice over message for emergency tones (A 4573)
- Optional remote volume (With A 4373 Digital volume control module fitted and external A 2280B wall plate)
- Rack Mountable (suits 19 inch racks) with optional A 4376 rack ears
|
|
This 250 Watt 4 channel mixer amplifier is specifically designed for applications requiring up to three microphone inputs, without compromising output power and overall performance. The amplifier feature three inputs which can be configured for either microphone or line level operation. |
 |
A4017 |
|
- To mount any of the Redback half rack products into a 19" wide racking system, the H 4990 bracket is required. If a single product is mounted into the H 4990, then a metal (H 4992) or plastic (H 4993) infill panel can be fitted for a neater finish.
|
|
Super compact with surprising performance specifications, intended for smaller PA system applications. Our engineering team based the design around a National TDA1519 monolithic IC achieving virtually "destruction proof" operation under quite severe misuse |
 |
A4380A |
|
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 70V, 100V and 4-16Ω outputs
- 240V AC or 24V DC operation
- 24V DC @ 1 Amp output for external devices
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicators
- Fault Indicators
- Power Status Indicators
- Rack Mountable (suits 19 inch racks)
|
|
This range of booster amplifiers are ideal for installations requiring high power zone amplifiers. Simply choose a power rating according to the wattage required for each zone. |
 |
A4336 |
|
- 5 inputs
- 6 output zones
- Direct 100V line output
- 4Ω output
- Individual zone attenuators (max 80W)
- 24V DC operation
- LED VU meter
- 2 year warranty
- Volume, treble and bass controls for each input
- Over current protection
- Over temperature protection
- Short circuit protection
- Telephone paging input
- Phantom power
- Selectable microphone priority
|
|
Housed in a heavy duty 3RU rack mount cabinet, these mixer amplifiers include a host of features and are ideally suited for schools, offices, medical suites, office/factory units etc. |
 |
A4199 |
|
- Amplifier type: Class D stereo
- Output power: 15W RMS per channel @ 4 ohm
- Distortion: 0.06%
- Headphone output: 105mW RMS per channel
- Headphone distortion: 0.05%
- Min load: 4Ω
- Current draw: 9A max.
- Power: 12V DC
- Dimensions: 285W x 128D x 43Hmm
- Weight: 0.8kg
|
|
Ideal for small businesses or simple multi-zone home audio systems. Switch between up to 4 different audio sources - connect up to 8 speakers. Toslink digital audio input for TV audio. Great for background music use. Also fitted with 6.35mm microphone connection. |
 |
A4157 |
|
- Output Power (Stereo 8Ω): 250W + 250W
- TA 1KHz THD≤1% (4Ω): 370W + 370W
- Bridge 8Ω: 740W
- Frequency Response: 20Hz-20KHz +/-0.5dB
- Input Sensitivity: 0.77V
- Maximum input level: 18dB/6.2V
- Input Impedance active balanced: 20KOHMS/Balanced, 10KOHMS/un-Balanced
- Signal/noise ration a-weighted RMS: ≥95dB
- Crosstalk at rated output power (8Ω 1kHz): >70dB
- Damping Factor (f=1kHz 8Ω): >240
- Slew rate internal: 15V/us
- Protection: Short circuit, current limited DC fault AC line fuse, thermal cut off, power up/down transients
- Indicators: POWER (BLUE) PROT (RED) CLIP (YELLOW) BR (GREEN) PAR (GREEN)
- Cooling: Variable Speed Fan
- Front Panel Controls: LEVEL ACH, BCH POWER SWITCH
- Rear Panel Controls: STEREO/BRIDGE/PARALLEL MODE SWITCH
- Connector: XLR BALANCED INPUT, PROFESSIONAL SPEAKON OUTPUT
- Power consumption half power 8Ω: <740W
- Power Supply: 240V AC/50Hz
- Interior Dimensions: 482 x 325.5 x 88mm
- Exterior Dimensions: 555 x 415 x 168mm
- Net Weight: 9kg
- Gross Weight: 10kg
|
|
The Apple series Biema power amplifiers are a cost effective solution for demanding commercial audio applications. These non-bridgeable models are designed to be used as standard 2 channel or stereo amplifiers. The design incorporates a fan forced cooling sys |
 |
A4155 |
|
- Output Power (Stereo 8Ω): 150W + 150W
- TA 1KHz THD≤1% (4Ω): 220W + 220W
- Bridge 8Ω: 440W
- Frequency Response: 20Hz-20KHz +/-0.5dB
- Input Sensitivity: 0.77V
- Maximum input level: 18dB/6.2V
- Input Impedance active balanced: 20KOHMS/Balanced, 10KOHMS/un-Balanced
- Signal/noise ration a-weighted RMS: ≥95dB
- Crosstalk at rated output power (8Ω 1kHz): >70dB
- Damping Factor (f=1kHz 8Ω): >240
- Slew rate internal: 15V/us
- Protection: Short circuit, current limited DC fault AC line fuse, thermal cut off, power up/down transients
- Indicators: POWER (BLUE) PROT (RED) CLIP (YELLOW) BR (GREEN) PAR (GREEN)
- Cooling: Variable Speed Fan
- Front Panel Controls: LEVEL ACH, BCH POWER SWITCH
- Rear Panel Controls: STEREO/BRIDGE/PARALLEL MODE SWITCH
- Connector: XLR BALANCED INPUT, PROFESSIONAL SPEAKON OUTPUT
- Power consumption half power 8Ω: <440W
- Power Supply: 240V AC/50Hz
- Interior Dimensions: 482 x 325.5 x 88mm
- Exterior Dimensions: 555 x 415 x 168mm
- Net Weight: 8.5kg
- Gross Weight: 10.5kg
|
|
The Apple series Biema power amplifiers are a cost effective solution for demanding commercial audio applications. These non-bridgeable models are designed to be used as standard 2 channel or stereo amplifiers. The design incorporates a fan forced cooling sys |
 |
A4198 |
|
- Amplifier type: Class D stereo
- Output power: 15W RMS per channel @ 4 ohm
- Distortion: 0.06%
- Headphone output: 105mW RMS per channel
- Headphone distortion: 0.05%
- Min load: 4Ω
- Current draw: 9A max.
- Power: 12V dc
- Dimensions: 205W x 108D x 26Hmm
- Weight: 0.5kg
|
|
Excellent for multi-room audio distribution, this 12V powered four zone amplifier produces 30W RMS per zone (15W RMS per channel) - all from a case just 200mm across! One input source may be connected on the front panel via stereo RCA sockets. |
 |
A4037 |
|
- 3 balanced microphone inputs
- Phantom power on mic inputs
- 3 line inputs
- 19” rack mount kit included
- VOX muting
- Tape output RCA sockets
- Bass and treble tone controls
- 100V line output (note: this model cannot be converted to 70V line as per others in the series)
- 240V AC or 24V DC operation
- Built in short circuit protection
- 10 year warranty
- Optional evac module available
- Optional remote volume module
- Australian designed & assembled
|
|
Designed to meet the requirements of medium sized professional public address installations, delivering an output power of 40W RMS respectively. |
 |
A4159 |
|
- Output Power (Stereo 8Ω): 350W + 350W
- TA 1KHz THD≤1% (4Ω): 500W + 500W
- Bridge 8Ω: 1000W
- Frequency Response: 20Hz-20KHz +/-0.5dB
- Input Sensitivity: 0.77V
- Maximum input level: 18dB/6.2V
- Input Impedance active balanced: 20KOHMS/Balanced, 10KOHMS/un-Balanced
- Signal/noise ration a-weighted RMS: ≥95dB
- Crosstalk at rated output power (8Ω 1kHz): >70dB
- Damping Factor (f=1kHz 8Ω): >240
- Slew rate internal: 15V/us
- Protection: Short circuit, current limited DC fault AC line fuse, thermal cut off, power up/down transients
- Indicators: POWER (BLUE) PROT (RED) CLIP (YELLOW) BR (GREEN) PAR (GREEN)
- Cooling: Variable Speed Fan
- Front Panel Controls: LEVEL ACH, BCH POWER SWITCH
- Rear Panel Controls: STEREO/BRIDGE/PARALLEL MODE SWITCH
- Connector: XLR BALANCED INPUT, PROFESSIONAL SPEAKON OUTPUT
- Power consumption half power 8Ω: <440W
- Power Supply: 240V AC/50Hz
- Interior Dimensions: 482 x 325.5 x 88mm
- Exterior Dimensions: 555 x 415 x 168mm
- Net Weight: 9.5kg
- Gross Weight: 11.5kg
|
|
The Apple series Biema power amplifiers are a cost effective solution for demanding commercial audio applications. These non-bridgeable models are designed to be used as standard 2 channel or stereo amplifiers. The design incorporates a fan forced cooling sys |
 |
A4376 |
|
|
|
1 Pair of bolt on rack ears to allow installation of amplifiers into a 19" rack system. Designed to fit the following Redback models:
A 4375, A 4385, A 4375A, A 4385A, A 4377, A 4387, A 4210, A 4212. |
 |
A4332 |
|
- 5 inputs
- 6 output zones
- Direct 100V line output
- 4Ω output
- Individual zone attenuators (max 40W)
- 24V DC operation
- LED VU meter
- 2 year warranty
- Volume, treble and bass controls for each input
- Over current protection
- Over temperature protection
- Short circuit protection
- Telephone paging input
- Phantom power
- Selectable microphone priority
|
|
Housed in a heavy duty 3RU rack mount cabinet, these mixer amplifiers include a host of features and are ideally suited for schools, offices, medical suites, office/factory units etc. |
 |
A4390A |
|
- Multi-stage thermally cued fan cooling
- Input signal presence indicator
- Output peak limited
- 2U 19" rack mount (ears included)
- 3 pin XLR input, 3 pin XLR loop out
- Level control rear mounted
- 100V, 70V and 4 - 16Ω outputs
- Thermal and overload protection
- 240V AC, or 24V DC operation
- 300mA 24V battery trickle charge
|
|
This booster is ideal for installations requiring a high power zone amplifier. Ideal for use in shopping centres, pedestrian precincts, public transport facilities and convention centres. |
 |
A4322 |
|
- 5 inputs
- 4 output zones
- 70V or 100V output
- 4Ω or 8Ω output
- 24V DC operation
- Over temperature, over current and short circuit protection
- LED VU meter
- 2 year warranty
- Telephone paging input
- Chime and siren
|
|
An economical solution for smaller installations including offices, workshops, smaller shopping arcades, schools etc. |
 |
A4324 |
|
- 5 inputs
- 4 output zones
- 70V or 100V output
- 4Ω or 8Ω output
- 24V DC operation
- Over temperature, over current and short circuit protection
- LED VU meter
- 2 year warranty
- Telephone paging input
- Chime and siren
|
|
An economical solution for smaller installations including offices, workshops, smaller shopping arcades, schools etc. |
 |
A4330 |
|
- 5 inputs
- 6 output zones
- Direct 100V line output
- 4Ω output
- Individual zone attenuators (max 20W)
- 24V DC operation
- LED VU meter
- 2 year warranty
- Volume, treble and bass controls for each input
- Over current protection
- Over temperature protection
- Short circuit protection
- Telephone paging input
- Phantom power
- Selectable microphone priority
|
|
Housed in a heavy duty 3RU rack mount cabinet, these mixer amplifiers include a host of features and are ideally suited for schools, offices, medical suites, office/factory units etc. |
 |
A4285C |
|
- VU meter on LCD screen
- Output peak limited
- Multi-stage thermally cued fan cooling
- 2U 19" rack mount
- Tape record out terminals
- Remote volume facility
- Optional alert, evac & chime tone generator (A 4573)
- Vox activated 24V dc output
- 6 inputs with 3 pin XLR or 2 x RCA sockets
- Phantom powering available on all inputs
- Three levels of priority
- Option for mic/line to operate vox muting on inputs 1 to 3
- Push to talk (PTT) terminals on rear panel
- Bass and treble tone controls
- Power amp line out connector
- Terminals for 100V line, 70V line and 4 - 16Ω loads
- 240V ac or 24V dc power operation
- Thermal & fuse overload protection
- Built in short circuit protection
- 300mA trickle charge facility for 24V dc batteries
- Master volume can be configured as pre or post line out
|
|
Engineered for professional PA installations, the A 4285B conservatively delivers 250W RMS power. Including three levels of input priority, bass and treble controls and phantom powering capability enable unparalleled flexibility for a wide scope of applications such as schools, shopping centres, workshops, mine sites and office buildings. |
