|
Description |
Downloads |
Specs |
Ordering |
|
 |
K8601 NEW
|
|
- Double sided PEI coated plate
- Excellent flatness & elasticity
- Strong adhesion
- Durable and long lasting textured plate
|
|
Double sided black textured PEI spring steel magnetic build plate to suit 3D printer models K8600 & K8602 |
 |
J0064 NEW
|
|
- Gear Ratio: 90:1
- Input Voltage: 12V
- No Load
- Speed: 66RPM
- Current: 0.3A
- Rated Load
- Speed: 50RPM
- Current: 1A
- Torque: 17kg-cm
- Stall Load
- Current: 3.8A
- Torque: 35kg-cm
|
|
This gearbox is suitable for a host of model and light industrial applications |
 |
H8958A NEW
|
|
- Great for better heat dissipation on the Pi 5.
- Access to all Pi Ports: Power, Video, Audio, USB, LAN, MicroSD Card.
- Slots for camera cables and GPIO access.
- Compatible with the Raspberry Pi 5.
- Includes cooling fan with header connection.
- Integral heatsink for added cooling efficiency.
|
|
This compact multi-layer acrylic case suits the Raspberry Pi 5 and provides access to all ports on the board. Includes cooling fan module with heatsink. |
 |
Z6319 NEW
|
|
- Large 3-digit display of measured temperature
- Operates in both a heating and cooling mode of operation
- Programmable settings for temp set point, temp hysteresis, compressor delay and temperature calibration.
- Waterproof NTC temperature sensor has -50 to +99.9°C measurement range with ±1°C accuracy
- Over temperature and sensor failure audible and visual alarm
- Unit temperature reading can be calibrated
- Relays switch up to 120/240VAC @ 10A or 15VDC @ 10A
- 12VDC module operation
|
|
The STC-1000 temperature controller is a self contained heating / cooling controller that operates on 12VDC and controls either AC or DC loads up to 10A max current. |
 |
Z6316 NEW
|
|
- Easy to set up and pair - Android or iOS eWeLink app available for direct control.
- Onboard Bluetooth status indicator and relay indicator.
- With 2 optocoupler isolation, strong anti-interference ability.
- Onboard N76E003/STM8S003 and SPP-C Bluetooth 2.1 module.
- Compact board design.
- Module with diode effusion protection short response time
|
|
A combined relay and control board with the ability to switch on and off connected loads using an App on your phone via Bluetooth. The eWeLink app offers seamless power switching using your device when in range of the relay board (typically 10m). |
 |
Z6587 NEW
|
|
- Easy, wireless communication up to 100m
- Create your own network of connected devices.
- Compact, on-board antenna
- 915MHz is suitable for amateur use in Australia.
- No soldering necessary
- 2x LEDs: Rx/Tx indicator, and user-controllable
- PiicoDev connector, compatible with Qwiic and STEMMA QT (3.3V only)
- 2.54mm breakout for breadboarding/prototyping
|
|
With this Transceiver users can unlock some very cool capabilities like collecting data from some distant sensor, or remote-controlling hardware. |
 |
Z6424 NEW
|
|
- RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom
- Dual-core Arm Cortex M0+ processor, flexible clock running up to 133 MHz
- 264KB of SRAM, and 2MB of on-board Flash memory
- USB 1.1 with device and host support
- Low-power sleep and dormant modes
- Drag-and-drop programming using mass storage over USB
- 26 × multi-function GPIO pins
- 2 × SPI, 2 × I2C, 2 × UART, 3 × 12-bit ADC, 16 × controllable PWM channels
- Accurate clock and timer on-chip
- Temperature sensor
- Accelerated floating-point libraries on-chip
- 8 × Programmable I/O (PIO) state machines for custom peripheral support
|
|
The Raspberry Pi Pico W is perfect for IoT and wireless projects, better still, it's such an affordable 32-bit microcontroller that is packed with peripheries including WiFi. |
 |
X3061 NEW
|
|
|
|
Barrel up rough terrain with this remote control dune buggy thats perfect for small kids and big kids! 1:43 scale. |
 |
Z6588 NEW
|
|
- A great guide to get you started with Raspberry Pi, Pico, or Micro:bit
- Backup power provided by a Supercapacitor - no batteries required!
- Tracks year, month, day, weekday, hour, minutes, seconds
- Schedule events or alarms
- Automatically switches between main power and backup power
- High accuracy clock - within 30 seconds per year
- PiicoDev Connector, compatible with Qwiic and STEMMA QT (3.3V Only)
|
COMING SOONThis item is arriving soon. |
The PiicoDev Precision Temperature Sensor features a low-power, high precision TMP117 with 16-bit resolution and an accuracy of ±0.1°C (across -20°C to +50°C) with no calibration required. |
 |
J0080 NEW
|
|
- Working Temperature: 0℃ - 40 ℃
- Motor voltage: 12VDC
- Motor current: 200-300mA
- Flow Rate : >80ml/min
- Tube Size : 5mm tube
- Pump Head Material : ABS
- Pump Pipe : Transparent silicone pipe
- Pulsations : Three roller
|
|
This 12V Peristaltic Water Dosing Pump can be used in a variety of applications. |
 |
Z6318 NEW
|
|
- GPS Breakout Module
- 2.7V-3.6V Supply
- Interfaces; UART, USB, SPI, DDC
- RT Crystal
- Antenna Supply and supervisor
- 3 Configuration Pairs
- 1 Timepulse pair
- External Interrupt/Wakeup
|
|
The NEO-6 module is a stand-alone GPS receiver featuring a high performance u-blox 6 positioning engine. |
 |
Z6421B NEW
|
|
- RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom
- Dual-core ARM Cortex M0 processor, flexible clock running up to 133 MHz
- 264kB of SRAM, and 2MB of on-board Flash memory
- Castellated module allows soldering direct to carrier boards
- USB 1.1 Host and Device support
- Low-power sleep and dormant modes
- Drag & drop programming using mass storage over USB
- 26 multi-function GPIO pins
- 2×SPI, 2×I2C, 2×UART, 3×12-bit ADC, 16×controllable PWM channels
- Accurate clock and timer on-chip
- Temperature sensor
- Accelerated floating point libraries on-chip
- 8×Programmable IO (PIO) state machines for custom peripheral support
|
|
Raspberry Pi Pico is a tiny, fast, and versatile board built using RP2040, a brand new microcontroller chip designed by Raspberry Pi in the UK. |
 |
Z6586 NEW
|
|
- Control up to four servos independently
- Daisy chain up to four Servo Drivers together for more complex projects
- No soldering necessary
- PiicoDev connector, compatible with Qwiic and STEMMA QT (3.3V only)
- 2.54mm breakout for breadboarding/prototyping
|
|
With this new servo driver users will be able to add the power of motion to projects. |
 |
ZA6421 NEW
|
|
- Ultra compact form factor
- Dual core ARM Cortex M0+ processor
- Two SPI controllers
- Two I2C controllers
- 16 PWM channels
- 26 multifunction GPIO pins
- Three analogue inputs
- On board USB controller
- In-built temperature sensor
- Castellated module allows soldering direct to carrier boards
- Drag-and-drop programming using mass storage over USB
- Low-power sleep and dormant modes
- Accurate on-chip clock
- Accelerated integer and floating-point libraries on-chip
|
|
Raspberry Pi Pico is a tiny, fast, and versatile board built using RP2350, a brand new microcontroller chip designed by Raspberry Pi in the UK. From controlling appliances to operating a light display, Raspberry Pi Pico puts the technology that underpins countless everyday operations into your hands. |
 |
Z6478 NEW
|
|
- Sensor size: 3.67 x 2.74 mm (1/4 format).
- Pixel count: 2592 x 1944.
- Pixel size: 1.4 x 1.4 um.
- Up to 90 fps video at vga.
- Sensor type: omnivision ov5647 color cmos qsxga (5-megapixel).
- Full-frame slr lens equivalent: 35 mm.
- Fixed focus: 1 m to infinity.
|
|
This camera module has been designed to be used with raspberry pi boards
|
 |
J0083 NEW
|
|
|
|
This 5mm tubing is made of silicone rubber which is flexible, resistant to high temperatures and does not deteriorate outdoors. |
 |
J0085 NEW
|
|
- Sensor Type: Hall effect
- Working Voltage: 5 to 18V DC (min tested working voltage 4.5V)
- Max current draw: 15mA @ 5V
- Output Type: 5V TTL
- Working Flow Rate: 1 to 30 Litres/Minute
- Working Temperature range: -25 to +80℃
- Working Humidity Range: 35%-80% RH
- Accuracy: ±10%
- Maximum water pressure: 2.0 MPa
- Output duty cycle: 50% +-10%
- Output rise time: 0.04us
- Output fall time: 0.18us
- Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min)
- Pulses per Litre: 450
- Durability: minimum 300,000 cycles
- Cable length: 150mm
- 1/2″ nominal pipe connections, 0.78″ outer diameter, 1/2″ of thread
- Size: 63.5 x 35.5 x 35.5mm
|
|
The YF-S201 Hall Effect Water Flow Meter Sensor comes with three wires: red (5-24VDC power), black (ground) and yellow (Hall effect pulse output). |
 |
Z6317 NEW
|
|
- 3-digit display of temperature
- Module can operate in a heating or cooling mode of operation
- Multiple parameters can be set such as temp trip point, hysteresis and delay.
- Waterproof NTC temperature sensor has -30 to +110°C measurement range with 0.1°C accuracy
- Relay switches up to 120VAC @ 10A or 14VDC @ 10A
- 12V module operation
|
|
This high precision temperature control module is a highly functional self-contained temperature controller module for both heating and cooling applications. |
 |
J0115 NEW
|
|
|
|
A plastic Mecanum wheel for robotics projects requiring omnidirectional movement. |
 |
J0116 NEW
|
|
|
|
A plastic Mecanum wheel for robotics projects requiring omnidirectional movement. |
 |
SA0910 NEW
|
|
- Switch Type: SPST microswitch
- Connection: 6.3mm spade
- Illumination: 5-12V input
- Max material thickness: 30mm
- Mounting Hole: 27.5mm
- Mounting depth: 61mm
|
|
Ideal for use in retro gaming projects or anywhere a jumbo momentary switch may be required. |
 |
SA0911 NEW
|
|
- Switch Type: SPST microswitch
- Connection: 6.3mm spade
- Illumination: 5-12V input
- Max material thickness: 30mm
- Mounting Hole: 27.5mm
- Mounting depth: 61mm
|
|
Ideal for use in retro gaming projects or anywhere a jumbo momentary switch may be required. |
 |
SA0912 NEW
|
|
- Switch Type: SPST microswitch
- Connection: 6.3mm spade
- Illumination: 5-12V input
- Max material thickness: 30mm
- Mounting Hole: 27.5mm
- Mounting depth: 61mm
|
|
Ideal for use in retro gaming projects or anywhere a jumbo momentary switch may be required. |
 |
SA0913 NEW
|
|
- Switch Type: SPST microswitch
- Connection: 6.3mm spade
- Illumination: 5-12V input
- Max material thickness: 30mm
- Mounting Hole: 27.5mm
- Mounting depth: 61mm
|
|
Ideal for use in retro gaming projects or anywhere a jumbo momentary switch may be required. |
 |
SA0914 NEW
|
|
- Switch Type: SPST microswitch
- Connection: 6.3mm spade
- Illumination: 5-12V input
- Max material thickness: 30mm
- Mounting Hole: 27.5mm
- Mounting depth: 61mm
|
|
Ideal for use in retro gaming projects or anywhere a jumbo momentary switch may be required. |
