|
Description |
Downloads |
Specs |
Ordering |
|
 |
Z6563 NEW
|
|
- Built-in 3.3V Voltage Regulator
- Labeled breakout pins
- Dedicated socket for nRF24 board.
- Suits the 8-pin NRF24L01 and NRF24L01 + PA + LNA modules
- Power status LED
|
|
This module is a compact circuit board designed to simplify the integration of the NRF24L01+ or NRF24L01+PA+LNA wireless transceiver module with other electronic boards and project designs. |
 |
Z6564 NEW
|
|
- Operating frequency: 2400MHz ~ 2524MHz
- Modulation: GMSK
- Receiver sensitivity: -95dbm
- Operating voltage: 2.7V ~ 3.6V
- Max current consumption when transmitting data: 115mA
- Max current consumption when receiving data: 45mA
- Gain of PA: 20 dB
- Gain of LNA: 10 dB
- Supply Voltage: Standard
- Dissipation Module: Standard
- Operating Temperature: -40 to 85°C
|
|
Operating in the 2.4GHz frequency band, the nRF24L01+PA+LNA is a wireless transceiver module designed for long-range communication while maintaining low power consumption. |
 |
Z6565 NEW
|
|
|
|
Unlock the potential of IoT and wireless communication with this versatile electronics kit! Designed for makers, hobbyists, and engineers, this kit includes an ESP32-WROOM-32D module, an nRF24L01+ wireless module with an antenna, a 0.96" OLED display, and essential accessories for seamless connectivity. |
 |
Z6566 NEW
|
|
|
|
A handy collection of sensors, parts and prototyping boards to help you get started with ESP32 development. Using the included breakout board and accompanying breadboards, this kit can be used to create a variety of custom designed projects using the plentiful programming resources found online. |
 |
Z6498 NEW
|
|
- Board material: international standard sheet, all tin pad, high strength fire drop material, disassembly, can be repeated.
- PCB board design features commonly used SMD components.
- The left and right of the three components are used to practice welding, each column with a test point.
- The middle of the circular circuit has been designed for the water lamp circuit, by the CD4017, NE555, light-emitting diodes, welding power can work.
- The circuit is also used on the back, a ruler to facilitate the measurement of components.There are examples of PCB conductors to facilitate the use of PCB design.
|
|
This Soldering SMD Practice Board Kit contains all the components needed for users to learn and improve their soldering abilities. |
 |
Z6497 NEW
|
|
- Integrated temperature and humidity sensing for precise control
- Wide temperature range from -20℃ to 60℃
- Full humidity control with a range of 0% to 100%
- High control accuracy of 0.1℃
- Relay output with a maximum capacity of 10A
- Compact and durable design with dimensions of 65*55*28mm
|
|
The XH-M452 Dual Output Temperature & Humidity Control Board is a versatile device designed for precision climate control applications. |
 |
Z6496 NEW
|
|
- Simple step and direction control interface
- Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step
- Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated
|
|
This breakout board is for A4988 DMOS Microstepping Driver with translator and overcurrent protection. |
 |
Z6495 NEW
|
|
- Non-contact detection, moving object detecting.
- This module's transmitting frequency is 24GHZ, can be widely applied in business, industries, word controlling etc.
- Provide various frequency range standards: -UK,-F.
- Advanced low consumption PHEMT oscillator.
- Independent transmitting and receiving route, can get the big gain.
- High sensibility, high flexibility, low cost, operating distance is 15m.
- Single channel operation
|
|
The CDM324 is a 24GHz Millimeter Wave Radar Sensor Module designed for reliable non-contact motion detectionand moving object detection. |
 |
Z6494 NEW
|
|
- Delivers up to 60W output with a 2-ohm load under a 24V power supply.
- Output power decreases proportionally for 4-ohm or 6-ohm loads.
- Supports a DC input range of 10-24V, ensuring flexibility for various power supply configurations.
- Designed in PBTL mode, enabling support for low resistance and high-power output
|
|
The TPA3118 60W Mono Digital Audio Power Amplifier Board is a high-performance audio amplifier designed for applications requiring compact size, low resistance, and high power output. |
 |
Z6493 NEW
|
|
- The PCA9685 offers 16 fully programmable PWM outputs with a 12-bit resolution, providing 4096 steps for precise duty cycle adjustments on each channel.
- The module uses the I2C bus for communication, ensuring easy integration with microcontrollers like Arduino or Raspberry Pi.
- Supports frequency control across all 16 channels, programmable between 24Hz and 1526Hz.
- The duty cycle (pulse width) can be fine-tuned from 0% to 100% for accurate output control.
- The on-board PWM controller manages all 16 channels independently, reducing processing load on the microcontroller compared to direct pin-based servo control.
- Multiple modules can be daisy-chained together. With up to 62 boards on a single I2C bus, you can control up to 992 servos using just two pins.
|
|
This 16 Channel PWM Servo Control Board is a versatile module that allows you to control up to 16 servos using only 2 pins via I2C communication. |
 |
Z6492 NEW
|
|
- Model: STM32F103C8T6
- Core: ARM 32-bit Cortex-M3 CPU
- Operating Frequency: Up to 72 MHz
- Flash Memory: 64KB
- SRAM: 20KB
- Operating Voltage: 2.0V to 3.6V
- I/O Logic Voltage: 2.0V to 3.6V
- Reset Functionality: Supports Power-On Reset (POR) and Power-Down Reset (PDR)
- Crystal Oscillator: 4-16 MHz for precise clocking
- On-board Mini USB port for both power supply and USB communication
- Colour: Black
- Material: Metal
- Dimensions: 53 x 22mm
|
|
The STM32F103C8T6 ARM STM32 SWD Development Board is an ideal platform for learners and developers looking to explore and master the STM32 microcontroller based on the ARM Cortex-M3 32-bit core. |
 |
Z6491 NEW
|
|
- Wide Current Range: Supports motor loads ranging from 5A to 22A, ensuring flexibility for various DC motor applications.
- PWM Technology: Utilizes Pulse Width Modulation to efficiently regulate motor speed while minimizing energy loss and heat generation.
- MOSFET Control: Integrated high-efficiency MOSFETs for stable, reliable, and high-current output performance.
- Compact Design: Designed for easy integration into small projects and enclosures.
|
|
The PWM MOSFET Motor Speed Controller is a high-performance module designed to provide precise control of DC motor speed using Pulse Width Modulation (PWM) technology. |
 |
Z6490 NEW
|
|
|
|
This expansion board as a driver expansion board, can be used for engraving machines, 3D printers. |
 |
Z6489 NEW
|
|
- Acts as a USB power bridge between a standard PD or QC3.0 USB power supply and your project.
- Select 5V, 9V, 12V, 15V or 20V using the on board button.
- LED display for chosen voltage.
- 5A maximum output current (up to 100W PD).
- Last voltage setting memory when power is disconnected.
|
|
The USB-C Fast Charge Trigger Board Module is a high-performance, versatile solution designed to provide fast and efficient charging for a wide range of devices. |
 |
Z6319 NEW
|
|
- Large 3-digit display of measured temperature
- Operates in both a heating and cooling mode of operation
- Programmable settings for temp set point, temp hysteresis, compressor delay and temperature calibration.
- Waterproof NTC temperature sensor has -50 to +99.9°C measurement range with ±1°C accuracy
- Over temperature and sensor failure audible and visual alarm
- Unit temperature reading can be calibrated
- Relays switch up to 120/240VAC @ 10A or 15VDC @ 10A
- 12VDC module operation
|
|
The STC-1000 temperature controller is a self contained heating / cooling controller that operates on 12VDC and controls either AC or DC loads up to 10A max current. |
 |
ZA6421 NEW
|
|
- Ultra compact form factor
- Dual core ARM Cortex M0+ processor
- Two SPI controllers
- Two I2C controllers
- 16 PWM channels
- 26 multifunction GPIO pins
- Three analogue inputs
- On board USB controller
- In-built temperature sensor
- Castellated module allows soldering direct to carrier boards
- Drag-and-drop programming using mass storage over USB
- Low-power sleep and dormant modes
- Accurate on-chip clock
- Accelerated integer and floating-point libraries on-chip
|
|
Raspberry Pi Pico is a tiny, fast, and versatile board built using RP2350, a brand new microcontroller chip designed by Raspberry Pi in the UK. From controlling appliances to operating a light display, Raspberry Pi Pico puts the technology that underpins countless everyday operations into your hands. |
 |
Z6440B NEW
|
|
- On board speaker
- MEMs Microphone with LED indicator
- Touch sensitive logo
- Built-in sleep/off mode that means the board can be powered-down with batteries connected
- Discrete regulator that can supply up to 190mA of current to external accessories
- 25 Programmable LEDs in a 5 x 5 grid
- 3-axis motion sensing
- On-board magnetometer
- On-board temperature sensor
- On-board light level sensing
- 2 x programmable buttons, A & B
- BLE Bluetooth 5.0
- 2.4Ghz Micro:bit Radio
- Rear-mounted push button
- Power off (push and hold power button)
- 25 pins
- MEMS microphone and LED indicator
- Onboard speaker
- Touch-sensitive logo pin
- LED power indicator
- C++, MakeCode, Python, Scratch
|
|
The Micro:bit go kit is easy to code with, all you need is your web browser and a micro USB cable and you are ready to start all kinds of exciting STEM/STEAM experiments, no need for any extra software to be installed. Kit includes USB cable, batteries and battery holder. |
 |
Z6318 NEW
|
|
- GPS Breakout Module
- 2.7V-3.6V Supply
- Interfaces; UART, USB, SPI, DDC
- RT Crystal
- Antenna Supply and supervisor
- 3 Configuration Pairs
- 1 Timepulse pair
- External Interrupt/Wakeup
|
|
The NEO-6 module is a stand-alone GPS receiver featuring a high performance u-blox 6 positioning engine. |
 |
Z6317 NEW
|
|
- 3-digit display of temperature
- Module can operate in a heating or cooling mode of operation
- Multiple parameters can be set such as temp trip point, hysteresis and delay.
- Waterproof NTC temperature sensor has -30 to +110°C measurement range with 0.1°C accuracy
- Relay switches up to 120VAC @ 10A or 14VDC @ 10A
- 12V module operation
|
|
This high precision temperature control module is a highly functional self-contained temperature controller module for both heating and cooling applications. |
 |
Z6316 NEW
|
|
- Easy to set up and pair - Android or iOS eWeLink app available for direct control.
- Onboard Bluetooth status indicator and relay indicator.
- With 2 optocoupler isolation, strong anti-interference ability.
- Onboard N76E003/STM8S003 and SPP-C Bluetooth 2.1 module.
- Compact board design.
- Module with diode effusion protection short response time
|
|
A combined relay and control board with the ability to switch on and off connected loads using an App on your phone via Bluetooth. The eWeLink app offers seamless power switching using your device when in range of the relay board (typically 10m). |
 |
J0085 NEW
|
|
- Sensor Type: Hall effect
- Working Voltage: 5 to 18V DC (min tested working voltage 4.5V)
- Max current draw: 15mA @ 5V
- Output Type: 5V TTL
- Working Flow Rate: 1 to 30 Litres/Minute
- Working Temperature range: -25 to +80℃
- Working Humidity Range: 35%-80% RH
- Accuracy: ±10%
- Maximum water pressure: 2.0 MPa
- Output duty cycle: 50% +-10%
- Output rise time: 0.04us
- Output fall time: 0.18us
- Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min)
- Pulses per Litre: 450
- Durability: minimum 300,000 cycles
- Cable length: 150mm
- 1/2″ nominal pipe connections, 0.78″ outer diameter, 1/2″ of thread
- Size: 63.5 x 35.5 x 35.5mm
|
|
The YF-S201 Hall Effect Water Flow Meter Sensor comes with three wires: red (5-24VDC power), black (ground) and yellow (Hall effect pulse output). |
 |
J0083 NEW
|
|
|
|
This 5mm tubing is made of silicone rubber which is flexible, resistant to high temperatures and does not deteriorate outdoors. |
 |
J0080 NEW
|
|
- Working Temperature: 0℃ - 40 ℃
- Motor voltage: 12VDC
- Motor current: 200-300mA
- Flow Rate : >80ml/min
- Tube Size : 5mm tube
- Pump Head Material : ABS
- Pump Pipe : Transparent silicone pipe
- Pulsations : Three roller
|
|
This 12V Peristaltic Water Dosing Pump can be used in a variety of applications. |
 |
Z6240A NEW
|
|
- Form factor compatible with earlier series of Arduino boards for compatibility with existing shields and projects.
- Expanded memory and faster clock speed
- Extra on-board peripherals including 12-bit DAC, CAN BUS and OP Amp.
- Wider input voltage range for integration with motors, LED strips and actuators.
- SWD connector for debugging.
- HID support for keystrokes and mouse movement.
|
|
Introducing the Funduino UNO R4 Minima compatible Arduino board. Equipped with the RA4M1 microprocessor, this board offers enhanced processing power, expanded memory, and more, all while maintaining the reliable UNO form factor and practical 5V operating voltage. Get ready for a remarkable upgrade! |
 |
ZW6240A NEW
|
|
- Form factor compatible with earlier series of Arduino boards for compatibility with existing shields and projects.
- Expanded memory and faster clock speed
- Extra on-board peripherals including 12-bit DAC, CAN BUS and OP Amp.
- Wider input voltage range for integration with motors, LED strips and actuators.
- HID support for keystrokes and mouse movement.
- Wi-FI and Bluetooth connectivity on board.
- Qwiic connector for I2C compatible sensors and actuators.
- LED matrix on board.
- Supports battery powered RTC.
|
|
The Funduino UNO R4 with WiFi is an Arduino compatible board integrating the powerful RA4M1 microcontroller with the robust wireless capabilities of the ESP32-S3 from Espressif. Additionally, it features an on-board 12x8 LED matrix, a Qwiic connector, a VRTC, and an OFF pin, making it an ideal choice for all your maker projects. |
