|
Description |
Downloads |
Specs |
Ordering |
|
 |
Z6319 NEW
|
|
- Large 3-digit display of measured temperature
- Operates in both a heating and cooling mode of operation
- Programmable settings for temp set point, temp hysteresis, compressor delay and temperature calibration.
- Waterproof NTC temperature sensor has -50 to +99.9°C measurement range with ±1°C accuracy
- Over temperature and sensor failure audible and visual alarm
- Unit temperature reading can be calibrated
- Relays switch up to 120/240VAC @ 10A or 15VDC @ 10A
- 12VDC module operation
|
|
The STC-1000 temperature controller is a self contained heating / cooling controller that operates on 12VDC and controls either AC or DC loads up to 10A max current. |
 |
Z6367A NEW
|
|
|
|
Utilises the 44E hall effect sensor for contactless magnetic switching. Output drops to ground when triggered. 3.3-5V input. 36 x 22 x 7mm |
 |
Z6382A NEW
|
|
- Dimensions: 32L x 25H x 24Wmm
- Sensor Outputs: Digital Output
- Required Supply Voltage: 5V - 20V
- Digital Output: 3.3V (High)
- Digital Output: 0V (Low)
- Quiescent Current: <50uA
- Delay Time: 0.5 - 200 Seconds
- Range 5m - 7m
- Angle Sensor: <100° cone angle
- Operating Temperature: -15°C to 70°C
- Lens size sensor: Ø23mm
|
|
When this motion sensor module is used in projects it can detect motion based on changes in infrared light in the environment. It is ideal to detect if a human has moved in or out of the sensor range. An LED will light up when movement is detected. This makes the module a great addition to security application projects. |
 |
Z6421B NEW
|
|
- RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom
- Dual-core ARM Cortex M0 processor, flexible clock running up to 133 MHz
- 264kB of SRAM, and 2MB of on-board Flash memory
- Castellated module allows soldering direct to carrier boards
- USB 1.1 Host and Device support
- Low-power sleep and dormant modes
- Drag & drop programming using mass storage over USB
- 26 multi-function GPIO pins
- 2×SPI, 2×I2C, 2×UART, 3×12-bit ADC, 16×controllable PWM channels
- Accurate clock and timer on-chip
- Temperature sensor
- Accelerated floating point libraries on-chip
- 8×Programmable IO (PIO) state machines for custom peripheral support
|
|
Raspberry Pi Pico is a tiny, fast, and versatile board built using RP2040, a brand new microcontroller chip designed by Raspberry Pi in the UK. |
 |
Z6424 NEW
|
|
- RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom
- Dual-core Arm Cortex M0+ processor, flexible clock running up to 133 MHz
- 264KB of SRAM, and 2MB of on-board Flash memory
- USB 1.1 with device and host support
- Low-power sleep and dormant modes
- Drag-and-drop programming using mass storage over USB
- 26 × multi-function GPIO pins
- 2 × SPI, 2 × I2C, 2 × UART, 3 × 12-bit ADC, 16 × controllable PWM channels
- Accurate clock and timer on-chip
- Temperature sensor
- Accelerated floating-point libraries on-chip
- 8 × Programmable I/O (PIO) state machines for custom peripheral support
|
|
The Raspberry Pi Pico W is perfect for IoT and wireless projects, better still, it's such an affordable 32-bit microcontroller that is packed with peripheries including WiFi. |
 |
Z6433 NEW
|
|
- XTensa dual-core 32-bit LX7 CPU, frequency up to 240MHz
- 2.4 GHz Wi-Fi, EEE 802.11 b/g/n-compliant
- Bluetooth, LE: Bluetooth 5, Bluetooth mesh
- 16 MByte(64Mbit) SPI Flash
- 384 KByte ROM
- 512 KByte SRAM
- 8 MByte(64Mbit) SPI PSRAM
- 16 KB SRAM in RTC
- Communication Interfaces: 2 x I2C, 2 x I2S, 4 x SPI, 3 x UART, 1 x USB OTG
- Security: 4096 bit OTP, AES, SHA, RSA, ECC and RNG, Secure boot, Flash encryption, Digital signature, HMAC module
- Dual Type-C USB connectors
- Reset and User/Firmware buttons
- RGB WS2812 User LED
- Power LED
- Virtual USB port provided by CP2102 for debugging and firmware upgrade
- Compact size of 50.1 x 13mm
- Supply Voltage: 5V via USB
- Circuit Voltage: 3.0 to 3.6V Circuit Operation
|
|
The ESP32-S3 development board is assembled with an original ESP32-S3-WROOM-1 module from Espressif, with 16MB Flash and 8MB PSRAM(ESP32-S3-WROOM-1-N16R8). It is a general-purpose Wi-Fi + Bluetooth® LE MCU module that integrates complete Wi-Fi and Bluetooth LE functions. |
 |
Z6434 NEW
|
|
- RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom
- Dual-core Arm Cortex M0+ processor, flexible clock running up to 133 MHz
- 264KB of SRAM, and 2MB of on-board Flash memory
- USB-C connector, keeps it up to date, easier to use
- The castellated module allows soldering directly to carrier boards
- USB 1.1 with device and host support
- Low-power sleep and dormant modes
- Drag-and-drop programming using mass storage over USB
- 29 × multi-function GPIO pins (20× via edge pinout, others via solder points)
- 2 × SPI, 2 × I2C, 2 × UART, 4 × 12-bit ADC, 16 × controllable PWM channels
- Accurate clock and timer on-chip
- Temperature sensor
- Accelerated floating-point libraries on-chip
- 8 × Programmable I/O (PIO) state machines for custom peripheral support
|
|
The RP2040-Zero, is a low-cost, high-performance Pico-like MCU board based on Raspberry Pi RP2040 microcontroller. 29 × multi-function GPIO pins. Configurable pin function, allows flexible development and integration. |
 |
Z6439B NEW
|
|
- On board speaker
- MEMs Microphone with LED indicator
- Touch sensitive logo
- Built-in sleep/off mode that means the board can be powered-down with batteries connected
- Discrete regulator that can supply up to 190mA of current to external accessories
- 25 Programmable LEDs in a 5 x 5 grid
- 3-axis motion sensing
- On-board magnetometer
- On-board temperature sensor
- On-board light level sensing
- 2 x programmable buttons, A & B
- BLE Bluetooth 5.0
- 2.4Ghz Micro:bit Radio
- Rear-mounted push button
- Power off (push and hold power button)
- 25 pins
- MEMS microphone and LED indicator
- Onboard speaker
- Touch-sensitive logo pin
- LED power indicator
- C++, MakeCode, Python, Scratch
|
|
The Micro:bit is easy to code with, all you need is your web browser and a micro USB cable and you are ready to start all kinds of exciting STEM/STEAM experiments, no need for any extra software to be installed. Micro:bit has also developed a mobile app for coding over Bluetooth (without a USB cable), that makes it even easier to get everyone codin |
 |
Z6440B NEW
|
|
- On board speaker
- MEMs Microphone with LED indicator
- Touch sensitive logo
- Built-in sleep/off mode that means the board can be powered-down with batteries connected
- Discrete regulator that can supply up to 190mA of current to external accessories
- 25 Programmable LEDs in a 5 x 5 grid
- 3-axis motion sensing
- On-board magnetometer
- On-board temperature sensor
- On-board light level sensing
- 2 x programmable buttons, A & B
- BLE Bluetooth 5.0
- 2.4Ghz Micro:bit Radio
- Rear-mounted push button
- Power off (push and hold power button)
- 25 pins
- MEMS microphone and LED indicator
- Onboard speaker
- Touch-sensitive logo pin
- LED power indicator
- C++, MakeCode, Python, Scratch
|
|
The Micro:bit go kit is easy to code with, all you need is your web browser and a micro USB cable and you are ready to start all kinds of exciting STEM/STEAM experiments, no need for any extra software to be installed. Kit includes USB cable, batteries and battery holder. |
 |
Z6478 NEW
|
|
- Sensor size: 3.67 x 2.74 mm (1/4 format).
- Pixel count: 2592 x 1944.
- Pixel size: 1.4 x 1.4 um.
- Up to 90 fps video at vga.
- Sensor type: omnivision ov5647 color cmos qsxga (5-megapixel).
- Full-frame slr lens equivalent: 35 mm.
- Fixed focus: 1 m to infinity.
|
|
This camera module has been designed to be used with raspberry pi boards
|
 |
Z6516A NEW
|
|
- 7’’ standard display, 1024x600 resolution
- Capacitive touch screen, maximum support 5 point touch
- Supports backlight control, the backlight can be turned off to save power
- Supports standard HDMI interface input.
- Can be used as general-purpose-use HDMI monitor, for example: connect with a computer HDMI as the sub-display (resolution of the output has to be able to adjust to 800X480)
- Used as a Raspberry Pi display that supports Raspbian, Ubuntu, Kodi, win10 IOT, single-touch, free drive etc.
- Works as a PC monitor, support win7, win8, win10 system 5 point touch (XP and older version system: single-point touch), free drive.
|
|
A 1024x600 touchscreen for Raspberry Pi that supports standard HDMI interface input which can be directly connected to Raspberry Pi. |
 |
Z6527A NEW
|
|
- Support Arduino Mega2560 Directly inserted
- With Full-angle IPS TFT panel
- On Board level conversion chip for 5V/3.3V MCU
- Compatible with 2.8~3.3V operation voltage level
- Compatible with Arduino-Series development Board.
- Provided 12-examples with Arduino ,3-examples with STM32
- With SD Card Socket
- With SPI FLASH circuit
|
|
A 480x320 display shield for the Arduino Mega utilising the ILI9486 chipset. Ideal for projects requiring sensor monitoring. |
 |
Z6584A NEW
|
|
- Measures acceleration and tilt
- Detect tapping, double-taps, and shaking
- Great guide to get you started
- PiicoDev connector, compatible with Qwiic and STEMMA QT (3.3V only)
- 2.54mm breakout for breadboarding/prototyping
|
|
The on-board LIS3DH can measure 16-bit acceleration data in ranges from 2g to 16g in all 3 axes. |
 |
Z6586 NEW
|
|
- Control up to four servos independently
- Daisy chain up to four Servo Drivers together for more complex projects
- No soldering necessary
- PiicoDev connector, compatible with Qwiic and STEMMA QT (3.3V only)
- 2.54mm breakout for breadboarding/prototyping
|
|
With this new servo driver users will be able to add the power of motion to projects. |
 |
Z6587 NEW
|
|
- Easy, wireless communication up to 100m
- Create your own network of connected devices.
- Compact, on-board antenna
- 915MHz is suitable for amateur use in Australia.
- No soldering necessary
- 2x LEDs: Rx/Tx indicator, and user-controllable
- PiicoDev connector, compatible with Qwiic and STEMMA QT (3.3V only)
- 2.54mm breakout for breadboarding/prototyping
|
|
With this Transceiver users can unlock some very cool capabilities like collecting data from some distant sensor, or remote-controlling hardware. |
 |
Z6588 NEW
|
|
- A great guide to get you started with Raspberry Pi, Pico, or Micro:bit
- Backup power provided by a Supercapacitor - no batteries required!
- Tracks year, month, day, weekday, hour, minutes, seconds
- Schedule events or alarms
- Automatically switches between main power and backup power
- High accuracy clock - within 30 seconds per year
- PiicoDev Connector, compatible with Qwiic and STEMMA QT (3.3V Only)
|
COMING SOONThis item is arriving soon. |
The PiicoDev Precision Temperature Sensor features a low-power, high precision TMP117 with 16-bit resolution and an accuracy of ±0.1°C (across -20°C to +50°C) with no calibration required. |
 |
Z6589 NEW
|
|
- Intuitive output: Air Quality Index
- Measures VOCs and eCO2
- A great guide to get you started
- PiicoDev connector, compatible with Qwiic and STEMMA QT (3.3V only)
- 2.54mm breakout for breadboarding/prototyping
- Manufactured and supported in Australia by Core Electronics
|
|
PiicoDev ENS160 Air Quality Sensor. Measure indoor air-quality - sensitive to fumes, cooking smells, humans. |
 |
ZA6421 NEW
|
|
- Ultra compact form factor
- Dual core ARM Cortex M0+ processor
- Two SPI controllers
- Two I2C controllers
- 16 PWM channels
- 26 multifunction GPIO pins
- Three analogue inputs
- On board USB controller
- In-built temperature sensor
- Castellated module allows soldering direct to carrier boards
- Drag-and-drop programming using mass storage over USB
- Low-power sleep and dormant modes
- Accurate on-chip clock
- Accelerated integer and floating-point libraries on-chip
|
|
Raspberry Pi Pico is a tiny, fast, and versatile board built using RP2350, a brand new microcontroller chip designed by Raspberry Pi in the UK. From controlling appliances to operating a light display, Raspberry Pi Pico puts the technology that underpins countless everyday operations into your hands. |
 |
ZW6240A NEW
|
|
- Form factor compatible with earlier series of Arduino boards for compatibility with existing shields and projects.
- Expanded memory and faster clock speed
- Extra on-board peripherals including 12-bit DAC, CAN BUS and OP Amp.
- Wider input voltage range for integration with motors, LED strips and actuators.
- HID support for keystrokes and mouse movement.
- Wi-FI and Bluetooth connectivity on board.
- Qwiic connector for I2C compatible sensors and actuators.
- LED matrix on board.
- Supports battery powered RTC.
|
|
The Funduino UNO R4 with WiFi is an Arduino compatible board integrating the powerful RA4M1 microcontroller with the robust wireless capabilities of the ESP32-S3 from Espressif. Additionally, it features an on-board 12x8 LED matrix, a Qwiic connector, a VRTC, and an OFF pin, making it an ideal choice for all your maker projects. |
