|
Description |
Downloads |
Specs |
Ordering |
|
|
P7463A NEW
|
|
- Supports 8K @ 60Hz
- 32Gbps Bandwidth total
- DisplayPort 1.4 Compliant
- HDCP 2.2 Compliant
- Hybrid fibre and copper cable
- Slimline plug suits 25mm conduit
|
|
This range of Optical DisplayPort male to male leads have been constructed and designed using hybrid fibre and copper cable to ensure high-definition performance. |
|
M8969 NEW
|
|
- MEPS efficiency level V
- Australian Standards Compliant
- Suitable for a range of electronic devices
- Compatible with Australian mains power point
|
|
24V DC 2A switch mode plug pack. |
|
Q2118 NEW
|
|
- Large easy to read LCD display with backlighting.
- Tests battery CCA, voltage, internal resistance, battery health and charge status.
- Provides "Good Battery", "Good Recharge", "Charge Retest", "Replace", "Bad Cell Replace" condition statuses.
- Supports all battery standards, JIS, DIN, IEC, EN, SAW, CA, CCA, GB, BCI, MCA.
- Short circuit and reverse polarity protection.
- Test history display.
- Tests batteries in-situ in vehicle or out of vehicle.
- Quick test function via AH input.
|
|
Detects and analyses battery voltage, cold cranking amperes (CCA), resistance (mΩ) and battery cell condition. |
|
Z0088A NEW
|
|
- A = 6.3mm B = 23mm C = 11mm
|
|
Rectifier Diode Bridges KBPC1504 400V 15 Amp, Metal |
|
Q1278B NEW
|
|
|
|
A handy fast reading digital thermometer suitable for a wide array of uses such as monitoring liquids in laboratory, kitchen or BBQ use - great for roasting meats home brew setups and more! |
|
Z6424 NEW
|
|
- RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom
- Dual-core Arm Cortex M0+ processor, flexible clock running up to 133 MHz
- 264KB of SRAM, and 2MB of on-board Flash memory
- USB 1.1 with device and host support
- Low-power sleep and dormant modes
- Drag-and-drop programming using mass storage over USB
- 26 × multi-function GPIO pins
- 2 × SPI, 2 × I2C, 2 × UART, 3 × 12-bit ADC, 16 × controllable PWM channels
- Accurate clock and timer on-chip
- Temperature sensor
- Accelerated floating-point libraries on-chip
- 8 × Programmable I/O (PIO) state machines for custom peripheral support
|
|
The Raspberry Pi Pico W is perfect for IoT and wireless projects, better still, it's such an affordable 32-bit microcontroller that is packed with peripheries including WiFi. |
|
P0230A NEW
|
|
-
- A: 5mm
- B: 5mm
- C: 10mm
|
|
Metal line socket to suit RG6 and RG59. |
|
P0065A NEW
|
|
|
|
6.35mm mono chassis mount socket with SPST contact switch. |
|
P1968 NEW
|
|
- Superspeed USB+ 10Gbps transfer speeds
- 100W power delivery for fast recharging of devices
- 3m length
- Ideal for connection to USB hubs with multiple peripherals
- Suitable for high resolution monitors and external drives requiring high data speeds
|
|
This type-C to type C USB cable features USB 3.2 Gen 2 compatibility and can be used to connect and power a variety of USB type C equipped devices. |
|
P1967 NEW
|
|
- Superspeed USB+ 10Gbps transfer speeds
- 100W power delivery for fast recharging of devices
- 1m length
- Ideal for connection to USB hubs with multiple peripherals
- Suitable for high resolution monitors and external drives requiring high data speeds
|
|
This type-C to type C USB cable features USB 3.2 Gen 2 compatibility and can be used to connect and power a variety of USB type C equipped devices. |
|
D2339A NEW
|
|
- Supports up to 1920 x 1080 @ 60Hz.
- Stylish brushed aluminium finish.
- Use with USB type A devices.
- Suitable for use with A-C adapter (sold separately) for connection to USB C devices.
- Plug and play, no external power required.
- Supported by most operating systems & devices.
|
|
This USB 3.0 to HDMI graphics adapter turns an available USB 3.0 port into an HDMI output. |
|
P8166 NEW
|
|
- 240V AC 10A outputs.
- 7 x Australian Sockets (AS/NZS 3112:2017 conforming).
- Electrical authority outlet device approved (AS/NZS 3105:2014 conforming).
- High surge protection.
- Overload protection.
- Power cord located at the rear for less interference.
- 19” rack ear mounting.
|
|
The neat solution to supplying mains power to your mounted equipment. |
|
X3219A NEW
|
|
|
|
Designed to work in conjunction with X3216A strip lighting. |
|
T2691A NEW
|
|
|
|
Hot air tip to suit Iroda lithium T2690A and T2694A only. |
|
Z6516A NEW
|
|
- 7’’ standard display, 1024x600 resolution
- Capacitive touch screen, maximum support 5 point touch
- Supports backlight control, the backlight can be turned off to save power
- Supports standard HDMI interface input.
- Can be used as general-purpose-use HDMI monitor, for example: connect with a computer HDMI as the sub-display (resolution of the output has to be able to adjust to 800X480)
- Used as a Raspberry Pi display that supports Raspbian, Ubuntu, Kodi, win10 IOT, single-touch, free drive etc.
- Works as a PC monitor, support win7, win8, win10 system 5 point touch (XP and older version system: single-point touch), free drive.
|
|
A 1024x600 touchscreen for Raspberry Pi that supports standard HDMI interface input which can be directly connected to Raspberry Pi. |
|
P7818B NEW
|
|
- Cable Entry: 3.2mm.
- Max Insulation Diameter: 11mm
- Rated current: 75A
- Rated voltage: 600V
- Insulation Resistance: 5000MΩ
- Average contact Resistance(micro-ohms):<180 1-5.
- Voltage Proof: 2200V(DC)
- Life Without load(Contact/Disconnect Cycles):To 10000
- Life With Load (Hot Plug 250 Cycles&120V): 50A
- Flammability:UL94 V-0
- Contact Barrel Wire Size(AWG):6~12AWG
- Connector holding force(LBF):250N Min
- Environment Temperatures:-20℃ to 125℃
|
|
Genuine Anderson Power DC 600V connector. |
|
Z0890A NEW
|
|
- Emitted Colour: Red
- Lens Appearance: Red, Diffused
- Power Consumption: 180mW (typical)
- Operating Voltage: 3 (min.), 11V (typ.) 12V (max.)
- Luminous Intensity: 70-150mcd
- Flash Frequency: 2Hz
- Peak Forward Current: 100mA (max)
- Continuous Forward Current: 30mA (max)
- Reverse Voltage: 5V (max)
- Reverse Current: 1µA (max)
- Wave Length: 620nm
- Beam Angle: 60°
|
|
5mm Red Flashing LED |
|
K9641 NEW
|
|
|
|
An assortment of straight pin boxed PCB connectors and matching plugs in 2, 3, 4 and 5 way varieties (10 of each plug and socket). Plus crimp pins to suit plug housings. 150pcs total. |
|
A2387A NEW
|
|
- Pluggable screw terminal connections
- 300W total RMS continuous power handling
- Heavy duty transformer based impedance system protects against power loss
- Left and right channels are completely isolated for safe operation with any amplifier
- Quick connect terminals will accomodate 16AWG to 22AWG wire
- Can be connected to two different amplifiers via A/B switch
- Circuit breaker protected
|
|
The A2387A is a high-power, dual-source, autoformer based speaker selector. Dual source operation makes two different amplifiers/receivers drive selected speakers simultaneously. |
|
K-8600D NEW
|
|
|
|
Replacement teflon bowden tubing to suit Creality Ender and other brands/types of 3D printer. 1m length. |
|
S4133 NEW
|
|
- Max Switching Voltage: 250V AC, 220V DC
- Max Switching Current: 0.5A AC, 2A DC (1A DC for UL approved applications)
- Max VA (Watts): 62VA (30W)
- Contact Material: Silver Palladium
- Coil Resistance: 64.3Ω
- Max Coil Power: 140mw
- Insulation Resistance: >1000MΩ @ 500V DC
- Dielectric Strength (for 1 min):
- 1000V AC between open contacts
- 1000V AC between coil & contact
- Electrical Life: 200,000 operations 1A 24V
- Mechanical Life: 10 million operations
- Dimensions: 14W x 9L x 5H mm
|
|
Fully sealed construction. 3V coil.
|
|
X7100 NEW
|
|
- Jumbo clock digits - read up to 30m away!
- Calendar display.
- Day of the week display.
- Temperature & humidity display.
- Programmable alarm with snooze function.
|
|
This handy jumbo LCD 12/24 hour clock, thermometer and calendar is great for around the home or office. The extra large clock digits allow it to be read up to 30m away. The screen also provides date, day of the week, temperature and humidity readings. |
|
Z0726 NEW
|
|
|
|
3mm Bi-colour LED 3 Leg Red/Green Water Clear |
|
Z6439B NEW
|
|
- On board speaker
- MEMs Microphone with LED indicator
- Touch sensitive logo
- Built-in sleep/off mode that means the board can be powered-down with batteries connected
- Discrete regulator that can supply up to 190mA of current to external accessories
- 25 Programmable LEDs in a 5 x 5 grid
- 3-axis motion sensing
- On-board magnetometer
- On-board temperature sensor
- On-board light level sensing
- 2 x programmable buttons, A & B
- BLE Bluetooth 5.0
- 2.4Ghz Micro:bit Radio
- Rear-mounted push button
- Power off (push and hold power button)
- 25 pins
- MEMS microphone and LED indicator
- Onboard speaker
- Touch-sensitive logo pin
- LED power indicator
- C++, MakeCode, Python, Scratch
|
|
The Micro:bit is easy to code with, all you need is your web browser and a micro USB cable and you are ready to start all kinds of exciting STEM/STEAM experiments, no need for any extra software to be installed. Micro:bit has also developed a mobile app for coding over Bluetooth (without a USB cable), that makes it even easier to get everyone codin |
|
P7805B NEW
|
|
- Amperage Rating: 30A
- Contacts Supplied: No
- Oper. Volt (AC): 600V
- Oper. Volt (DC): 600V
- Type: Contact
- RoHS: Yes
- Wire Size (AWG): 12-16
- Wire Size (mm²): 1.3-3.3
|
|
High current DC connectors as used in automotive and industrial applications. Anderson PowerPole Style. |