Redback
| Description | Downloads | Specs | Ordering | ||
|---|---|---|---|---|---|
 |
Line Level Compressor/LimiterA4948 |
|
| This compact module is designed to go inline with an audio input source like CD/Blu-Ray etc to the input of a mixer or amplifier. It maintains a constant level to the mixer/amp regardless of the amplitude of the input signal. | |
 |
Paging Microphone Chime ModuleA4950 |
|
| By adding this module inline with a paging microphone pre and post announcement chimes can be added to the audio signal. | |
 |
5 Pin XLR Cat5 Extender (Transmitter)A4952 |
| This handy interface box allows balanced signals to be transmitted over long distances using economical UTP data cabling, and provides easy local zone connection for audio sources. | ||
 |
5 Pin XLR Transmitter WallplateA4953 |
|
| This handy interface wallplate allows balanced signals to be transmitted over long distances using economical UTP data cabling. | |
 |
5 Pin XLR Cat5 Extender (Receiver)A4954 |
| The Redback® A 4954 receives audio from compatible Redback® Cat5e/6 transmitters and converts the signal to a balanced XLR output with PTT connection. | ||
 |
5 Pin XLR Supermarket Microphone Transmitt...A4960 NEW |
|
| Designed for systems that use a large number of Redback C0325/6 mics such as supermarkets and hardware stores. This design is very unique in that it allows you to install unlimited PTT mics on a single circuit, but only allow one mic at a time to operate. | |
 |
Supermarket PTT Microphone TransceiverA4962 NEW |
|
| Designed for systems that use a large number of Redback C0325/6 mics such as supermarkets and hardware stores. This design is very unique in that it allows you to install unlimited PTT mics on a single circuit, but only allow one mic at a time to operate. | |
 |
4 Input 3 Tier Priority MixerA5131 |
|
| This four channel mixer features 4 balanced mic inputs and 3 line inputs. Input 1 is a dedicated balanced mic input whilst inputs 2 - 4 can accept either balanced mic or line level. | |
 |
4 Input Microphone HubA5135 |
|
| Designed with small supermarkets in mind. We've designed the hub to cater for industry standard supermarket 5 pin XLR microphones which connects to a local wallplate (A 5138) over a Cat5/6 cable. | |
 |
5 Pin XLR PTT Microphone Wallplate UTP Tra...A5138 |
|
| The A5138 UTP wall plate has a standard 5 Pin XLR connector for connection of microphones with PTT switches. | |
 |
3 Relay, 2 Serial Control Hub With PIR Tri...A6505A |
|
| Designed to be used in conjunction with the A 6500A programmable touchscreen wallplate, this control hub enables the control of a variety of devices. Connection to the A 6500A wallplate is via Cat5/6 cable up to 50m away. Now with PIR trigger input. | |
 |
RS485 Serial 100V Line AttenuatorA6507 |
|
| This compact module includes a seven step 100V line speaker attenuator/volume control which can be remotely adjusted via RS 485 serial control. | |
 |
12 Relay Serial Box For Redback Touch Wall...A6510 |
|
| Designed to be used in conjunction with Redback Touch programmable touchscreen wallplates, as a standalone system or as an expansion hub for the A 6505A, this control hub consists of 12 relays with isolated sets of voltage free contacts that close on operation. | |
 |
Single Serial Volume ControllerA6512 |
|
| These compact modules are designed to remotely alter the volume of any low level signal source feeding any amplifier or mixer remotely, via RS 232 or RS 485 serial control. They will interface with the Redback A 6500 wallplate or any other 3rd party control system. Requires 24V DC power supply. Includes one input with remote volume adjustment via s | |
 |
Dual Serial Volume ControllerA6514 |
|
| These compact modules are designed to remotely alter the volume of any low level signal source over serial control. | |
 |
2 Relay (High Current) Control Box For Red...A6515 |
|
| This relay hub consists of 2 high current (16A) relays with isolated sets of voltage free contacts that close on operation. The relay hub can be used in three ways. | |
 |
Programmable Universal 7" Touchscreen Wall...A6530 NEW |
|
| This universal 7" touchscreen wallplate is the perfect control system for commercial and domestic automation. Its stylish low profile design lends itself to installation in new modern homes, classrooms, lecture theatres or corporate boardrooms. | |
 |
Programmable Universal 7" Touchscreen Wall...A6531 |
|
| This universal 7" touchscreen wallplate is the perfect control system for commercial and domestic automation. Its stylish low profile design lends itself to installation in new modern homes, classrooms, lecture theatres or corporate boardrooms. | |
 |
Programmable Universal 4.3" Touchscreen Wa...A6540 |
|
| This universal touchscreen wallplate is the perfect control system for commercial and domestic automation. Its stylish low profile design lends itself to installation in new modern homes, classrooms, lecture theatres or corporate boardrooms. | |
 |
Programmable Universal 4.3" Touchscreen Wa...A6541 NEW |
|
| This universal touchscreen wallplate is the perfect control system for commercial and domestic automation. Its stylish low profile design lends itself to installation in new modern homes, classrooms, lecture theatres or corporate boardrooms. | |
 |
3 Pin XLR Handheld Supermarket Paging Mic...C0324 |
|
| This incredibly sturdy all metal microphone is built to survive the rigours of supermarkets & fast food restaurants. | |
 |
5 Pin XLR Handheld Supermarket Paging Mic...C0325 |
|
| This incredibly sturdy all metal microphone is built to survive the rigours of supermarkets & fast food restaurants. | |
 |
90° 5 Pin XLR Handheld Supermarket Pagin...C0326 |
|
| This incredibly sturdy all metal microphone is built to survive the rigours of supermarkets & fast food restaurants. | |
 |
Gooseneck Supermarket Paging MicrophoneC0327 |
|
| This incredibly sturdy all metal microphone is built to survive the rigours of supermarkets & fast food restaurants. | |
 |
CB Type Curly 0.75m Microphone Lead With B...C0330B |
| 0.75m curly cable to suit CB fist type microphone. Bare end connection for terminating to OEM equipment or with the connector of your choice. | ||
 |
CB Type Microphone With Bare EndsC0333 |
| Low impedance, 500 Ohm, omni-directional, dynamic microphone with curly cord (including switch pair). Suitable for CB's, radio transceivers etc. Supplied complete with mounting clip.Tailored frequency response 300Hz- 8KHz (C 0334), 300Hz - 6kHz (C 0335) | ||
 |
5 Pin XLR CB Type Balanced MicrophoneC0334 |
| Low impedance, 500 Ohm, omni-directional, dynamic microphone with curly cord (including switch pair). Suitable for CB's, radio transceivers etc. Supplied complete with mounting clip.Tailored frequency response 300Hz- 8KHz (C 0334), 300Hz - 6kHz (C 0335) | ||
 |
CB Type Balanced Microphone With Bare EndsC0335 |
| Low impedance, 500 Ohm, omni-directional, dynamic microphone with curly cord 2m (including switch pair). Suitable for CB''''s, radio transceivers etc. Supplied complete with mounting clip.Tailored frequency response 300Hz- 8KHz | ||
 |
CB Type Microphone Mounting ClipC0336 |
| Microphone clip to suit the C 0333/C 0334 / C 0335 range of CB microphones. | ||
 |
12mm Lapel Microphone WindsockC0337 |
| Used to negate breath noise and eliminate wind or breath "pop". This windsock is designed specifically to suit our lapel microphone and is sold as both a spare part and as a generic unit. | ||
 |
8mm Windsock To Suit C8911AC0338 |
| This windsock is designed specifically to suit C8911A headband microphone and is sold as both a spare part and as a generic unit. | ||
 |
20mm Pencil Microphone WindsockC0340 |
| Used to negate breath noise and eliminate wind or breath 'pop' | ||
 |
27mm Medium Microphone WindsockC0342 |
| Used to negate breath noise and eliminate wind or breath “pop”. | ||
 |
40mm Ball Microphone WindsockC0344 |
| Used to negate breath noise and eliminate wind or breath “pop”. | ||
 |
10mm Pencil Microphone WindsockC0345 |
| Used to negate breath noise and eliminate wind or breath “pop”. | ||
 |
Windsock to suit C0375C0346 |
| Used to negate breath noise and eliminate wind or breath "pop". Size refers to inside diameter of windsock opening.7mm | ||
 |
Windsock to suit C0361C0347 |
| Used to negate breath noise and eliminate wind or breath “pop”. Suits C 0361 shotgun microphone. | ||
 |
Windsock to suit C8914C0348 |
| Spare windsock to suit | ||
 |
Boundary Mic Pro ElectretC0351A |
|
| This boundary microphone is designed to be surface mounted and is fitted with a high sensitivity electret insert. The sturdy diecast case and steel grille offers robust protection, while the rubber base plate minimises vibration pickup. A front panel on/o | |
 |
Dynamic Insert Gooseneck PTT MicrophoneC0354 |
|
| A high performance dynamic microphone with in-built PTT switch in the head for paging systems. Complete with flexible gooseneck and built in 3 pin male XLR connector, it is ideal for paging consoles and general announcing requirements in factories, warehouses, food outlets and venues. | |
 |
Phantom Powered Choir MicrophoneC0356 |
|
| This cardioid microphone is designed to be mounted from ceilings in installations such as churches where greater noise isolation is required. Low profile design and flexible cable hanger provide for diverse mounting options and minimum visibility. Phant | |
 |
Desktop Phantom Power SupplyC0357 |
|
| A compact single channel phantom power supply with 3 pin XLR female balanced input and 3 pin XLR male balanced 48V output. Includes power supply. Size: 88W x 47H x 92Dmm | |
 |
Phantom Power Supply with Mini XLRC0358 |
| Powered by 1 AA battery, this module provides phantom power for mics equipped with a 3 pin mini XLR plug. A handy 'bass cut' switch is provided, giving the user ability to reduce breath and movement noise. It provides a standard 3 pin XLR output for conne | ||
 |
Electret Shotgun MicrophoneC0361 |
|
| This shotgun mic is designed to plug directly into a desk mount XLR socket. The line + gradient pattern provides an extremely tight unidirectional pickup and high rejection of back & side signals. It features a section of flexible gooseneck for angle adju | |
 |
Dynamic Screw Mount Gooseneck MicrophoneC0363 |
|
| This elegant gooseneck microphone features smooth, brilliant sound with excellent ambient noise control and feedback rejection. It's screw base is suitable for mounting on equipment or permanent desk mounting . The slimline design of this mic makes it id | |
 |
Redback Phantom Powered Lectern MicrophoneC0369 ROHS |
|
| This elegant gooseneck microphone features smooth, brilliant sound with excellent ambient noise control and feedback rejection. It is ideal for installations requiring the use of a high performance non-obtrusive microphone. The slimline design of this mic | |
 |
Lectern Dynamic Low Impedance MicrophoneC0370 |
|
| This microphone features speech tailored frequency response with excellent noise isolation and feedback rejection. Complete with flexible gooseneck and built in 3 pin male XLR connector, this is ideal for lecterns, custom paging consoles, church pulpits a | |
 |
Dynamic Lectern MicrophoneC0373 |
|
| This microphone features outstanding speech intelligibility, feedback rejection and user sound insolation. Complete with flexible gooseneck and built in 3 pin male XLR connector, this is ideal for lecterns, custom paging consoles, church pulpits and some | |
 |
Desk Paging Microphone PTT/PTLC0375 |
|
| An elegant, stylish, slimline unobtrusive desk-mount paging microphone equipped with a 3 pin balanced XLR lead. Features switchable flat or rolloff response to eliminate low frequency pickup. May also be switched to operate as push to talk or push to lock | |
 |
3 Pin XLR Desk Paging MicrophoneC0377 |
|
| This desk microphone has a tapered low frequency response for articulate speech reproduction and enhanced clarity. Fitted with a 2 metre lead and terminated with either a 3 pin XLR, 5 pin XLR or 5 pin DIN connector. The 5 pin XLR and 5 pin DIN type conn |
100% developed, designed & assembled in Australia.
Backed by an industry leading 10 Year Manufacturer Warranty.
