|
Description |
Downloads |
Specs |
Ordering |
|
 |
Z6319 NEW
|
|
- Large 3-digit display of measured temperature
- Operates in both a heating and cooling mode of operation
- Programmable settings for temp set point, temp hysteresis, compressor delay and temperature calibration.
- Waterproof NTC temperature sensor has -50 to +99.9°C measurement range with ±1°C accuracy
- Over temperature and sensor failure audible and visual alarm
- Unit temperature reading can be calibrated
- Relays switch up to 120/240VAC @ 10A or 15VDC @ 10A
- 12VDC module operation
|
|
The STC-1000 temperature controller is a self contained heating / cooling controller that operates on 12VDC and controls either AC or DC loads up to 10A max current. |
 |
ZA6421 NEW
|
|
- Ultra compact form factor
- Dual core ARM Cortex M0+ processor
- Two SPI controllers
- Two I2C controllers
- 16 PWM channels
- 26 multifunction GPIO pins
- Three analogue inputs
- On board USB controller
- In-built temperature sensor
- Castellated module allows soldering direct to carrier boards
- Drag-and-drop programming using mass storage over USB
- Low-power sleep and dormant modes
- Accurate on-chip clock
- Accelerated integer and floating-point libraries on-chip
|
|
Raspberry Pi Pico is a tiny, fast, and versatile board built using RP2350, a brand new microcontroller chip designed by Raspberry Pi in the UK. From controlling appliances to operating a light display, Raspberry Pi Pico puts the technology that underpins countless everyday operations into your hands. |
 |
Z6440B NEW
|
|
- On board speaker
- MEMs Microphone with LED indicator
- Touch sensitive logo
- Built-in sleep/off mode that means the board can be powered-down with batteries connected
- Discrete regulator that can supply up to 190mA of current to external accessories
- 25 Programmable LEDs in a 5 x 5 grid
- 3-axis motion sensing
- On-board magnetometer
- On-board temperature sensor
- On-board light level sensing
- 2 x programmable buttons, A & B
- BLE Bluetooth 5.0
- 2.4Ghz Micro:bit Radio
- Rear-mounted push button
- Power off (push and hold power button)
- 25 pins
- MEMS microphone and LED indicator
- Onboard speaker
- Touch-sensitive logo pin
- LED power indicator
- C++, MakeCode, Python, Scratch
|
|
The Micro:bit go kit is easy to code with, all you need is your web browser and a micro USB cable and you are ready to start all kinds of exciting STEM/STEAM experiments, no need for any extra software to be installed. Kit includes USB cable, batteries and battery holder. |
 |
Z6318 NEW
|
|
- GPS Breakout Module
- 2.7V-3.6V Supply
- Interfaces; UART, USB, SPI, DDC
- RT Crystal
- Antenna Supply and supervisor
- 3 Configuration Pairs
- 1 Timepulse pair
- External Interrupt/Wakeup
|
|
The NEO-6 module is a stand-alone GPS receiver featuring a high performance u-blox 6 positioning engine. |
 |
Z6317 NEW
|
|
- 3-digit display of temperature
- Module can operate in a heating or cooling mode of operation
- Multiple parameters can be set such as temp trip point, hysteresis and delay.
- Waterproof NTC temperature sensor has -30 to +110°C measurement range with 0.1°C accuracy
- Relay switches up to 120VAC @ 10A or 14VDC @ 10A
- 12V module operation
|
|
This high precision temperature control module is a highly functional self-contained temperature controller module for both heating and cooling applications. |
 |
Z6316 NEW
|
|
- Easy to set up and pair - Android or iOS eWeLink app available for direct control.
- Onboard Bluetooth status indicator and relay indicator.
- With 2 optocoupler isolation, strong anti-interference ability.
- Onboard N76E003/STM8S003 and SPP-C Bluetooth 2.1 module.
- Compact board design.
- Module with diode effusion protection short response time
|
|
A combined relay and control board with the ability to switch on and off connected loads using an App on your phone via Bluetooth. The eWeLink app offers seamless power switching using your device when in range of the relay board (typically 10m). |
 |
J0085 NEW
|
|
- Sensor Type: Hall effect
- Working Voltage: 5 to 18V DC (min tested working voltage 4.5V)
- Max current draw: 15mA @ 5V
- Output Type: 5V TTL
- Working Flow Rate: 1 to 30 Litres/Minute
- Working Temperature range: -25 to +80℃
- Working Humidity Range: 35%-80% RH
- Accuracy: ±10%
- Maximum water pressure: 2.0 MPa
- Output duty cycle: 50% +-10%
- Output rise time: 0.04us
- Output fall time: 0.18us
- Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min)
- Pulses per Litre: 450
- Durability: minimum 300,000 cycles
- Cable length: 150mm
- 1/2″ nominal pipe connections, 0.78″ outer diameter, 1/2″ of thread
- Size: 63.5 x 35.5 x 35.5mm
|
|
The YF-S201 Hall Effect Water Flow Meter Sensor comes with three wires: red (5-24VDC power), black (ground) and yellow (Hall effect pulse output). |
 |
J0083 NEW
|
|
|
|
This 5mm tubing is made of silicone rubber which is flexible, resistant to high temperatures and does not deteriorate outdoors. |
 |
J0080 NEW
|
|
- Working Temperature: 0℃ - 40 ℃
- Motor voltage: 12VDC
- Motor current: 200-300mA
- Flow Rate : >80ml/min
- Tube Size : 5mm tube
- Pump Head Material : ABS
- Pump Pipe : Transparent silicone pipe
- Pulsations : Three roller
|
|
This 12V Peristaltic Water Dosing Pump can be used in a variety of applications. |
 |
Z6240A NEW
|
|
- Form factor compatible with earlier series of Arduino boards for compatibility with existing shields and projects.
- Expanded memory and faster clock speed
- Extra on-board peripherals including 12-bit DAC, CAN BUS and OP Amp.
- Wider input voltage range for integration with motors, LED strips and actuators.
- SWD connector for debugging.
- HID support for keystrokes and mouse movement.
|
|
Introducing the Funduino UNO R4 Minima compatible Arduino board. Equipped with the RA4M1 microprocessor, this board offers enhanced processing power, expanded memory, and more, all while maintaining the reliable UNO form factor and practical 5V operating voltage. Get ready for a remarkable upgrade! |
 |
ZW6240A NEW
|
|
- Form factor compatible with earlier series of Arduino boards for compatibility with existing shields and projects.
- Expanded memory and faster clock speed
- Extra on-board peripherals including 12-bit DAC, CAN BUS and OP Amp.
- Wider input voltage range for integration with motors, LED strips and actuators.
- HID support for keystrokes and mouse movement.
- Wi-FI and Bluetooth connectivity on board.
- Qwiic connector for I2C compatible sensors and actuators.
- LED matrix on board.
- Supports battery powered RTC.
|
|
The Funduino UNO R4 with WiFi is an Arduino compatible board integrating the powerful RA4M1 microcontroller with the robust wireless capabilities of the ESP32-S3 from Espressif. Additionally, it features an on-board 12x8 LED matrix, a Qwiic connector, a VRTC, and an OFF pin, making it an ideal choice for all your maker projects. |
 |
A0713 NEW
|
|
- Operating voltage: 12 - 15 V/DC
- Current consumption: approx. 20 mA / 80 mA (relay off / on)
- Adjustable time: approx. 2 sec. to 23 min., (± 30 %)
- Connection: via flat-pin plug at the module
- LED: 2 (1 x LED operating voltage, 1 x LED relay “ON”)
- Relay point: 1 x ON, max. 3A, max 25V
- Dimensions: approx. 87 x 60 x 33 mm (with flanges)
|
|
Avoid the hassle with this pre-assembled timing controller, conveniently packaged in a compact and reliable form. It's easy to connect and versatile enough to adapt to your requirements. The start and stop functions are managed by simple switching contacts, and the relay output can control devices up to 25VDC at 3A. |
 |
H8960A NEW
|
|
- Great for better heat dissipation on the Pi 5.
- Access to all Pi Ports: Power, Video, Audio, USB, LAN, MicroSD Card.
- Compatible with the Raspberry Pi 5.
- Includes cooling fan with header connection.
- Includes 3 heatsinks.
|
|
An all metal Raspberry Pi 5 case with internal cooling fan and heatsinks. |
 |
H8958A NEW
|
|
- Great for better heat dissipation on the Pi 5.
- Access to all Pi Ports: Power, Video, Audio, USB, LAN, MicroSD Card.
- Slots for camera cables and GPIO access.
- Compatible with the Raspberry Pi 5.
- Includes cooling fan with header connection.
- Integral heatsink for added cooling efficiency.
|
|
This compact multi-layer acrylic case suits the Raspberry Pi 5 and provides access to all ports on the board. Includes cooling fan module with heatsink. |
 |
Z6379X |
|
|
|
Detects soil humidity levels - a handy little sensor for building automated watering and retic systems. 3.3-5V input. Note: typical lifespan of about a year when left in soil permanently. 58L x 20Wmm. |
 |
Z6434 NEW
|
|
- RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom
- Dual-core Arm Cortex M0+ processor, flexible clock running up to 133 MHz
- 264KB of SRAM, and 2MB of on-board Flash memory
- USB-C connector, keeps it up to date, easier to use
- The castellated module allows soldering directly to carrier boards
- USB 1.1 with device and host support
- Low-power sleep and dormant modes
- Drag-and-drop programming using mass storage over USB
- 29 × multi-function GPIO pins (20× via edge pinout, others via solder points)
- 2 × SPI, 2 × I2C, 2 × UART, 4 × 12-bit ADC, 16 × controllable PWM channels
- Accurate clock and timer on-chip
- Temperature sensor
- Accelerated floating-point libraries on-chip
- 8 × Programmable I/O (PIO) state machines for custom peripheral support
|
|
The RP2040-Zero, is a low-cost, high-performance Pico-like MCU board based on Raspberry Pi RP2040 microcontroller. 29 × multi-function GPIO pins. Configurable pin function, allows flexible development and integration. |
 |
Z6338X |
|
- Input Range: 3.8V to 32V.
- Output Range: 1.25V to 35V.
- Input Current: 3A (max),
- No-Load Current: 18mA (5V input, 8V output*)
- *No-load current is less than 18mA. Higher the voltage, the greater the no load current.
|
|
A converter module allowing a low input voltage to be increased to a higher output voltage. Input 3.8-32V DC. Output 1.25-35V DC. Ideal for powering higher voltage devices from a typical 5V microcontroller platform. 3A continuous current. |
 |
K8300A |
|
- Power: 5V DC 2A
- Nozzle Diameter: 0.6mm
- Pen Dimension: 18.5 x2.9 x 4.3cm
- Heating Temperature: 185-210C
- Materials Filament: Suitable for 1.75mm PLA and ABS
- Moulding Speed: Adjustable (3 levels)
|
|
A crafty addition to any work space this handheld pen extrudes 1.75mm PLA or ABS filament for decorating objects, simple plastic repair jobs or touch ups to 3D printed models. |
 |
J0070A NEW
|
|
- Step Angle: 1.8Deg
- Temperature Rise: 80DegC max
- Ambient Temperature: -20DegC~+50DegC
- Insulation Resistance: 100 MOhm Min. ,500VDC
- Dielectric Strength: 500VAC for 1minute
- Shaft Radial Play: 0.02Max. (450g-load)
- Shaft Axial Play: 0.08Max. (450g-load)
- Max. radial force: 28N (20mm from the flange)
- Max. axial force: 10N
- Product description: 42 two-phase stepping motor Body length 34mm Static torque 2.2kg.cm
- 5mm shaft diameter with flat wire, length 24mm,
- Wiring method: black green A +, A-. Red blue B +, B-,
- Adapter driver JK0220 (driving voltage DC12V ~ 36V, AC12V ~ 24V, current range 0.3A ~ 2.0A)
|
|
12V 200-step 1.8° 48BYG stepper motor with interface
lead. 2 phase type. 0.23Nm holding torque. 5mmØ
shaft. NEMA17 M3 mounting hole pattern (31mm).
Size: 42x42x34 (25mm shaft). 1m lead. |
 |
Z6315A NEW
|
|
|
|
A handy parts kit containing everything you need to start learning Arduino and building projects. Includes a huge selection of sensor boards, LEDs, pots, jumper wires, a breadboard, LCD screen and much more! |
 |
Z6588 NEW
|
|
- A great guide to get you started with Raspberry Pi, Pico, or Micro:bit
- Backup power provided by a Supercapacitor - no batteries required!
- Tracks year, month, day, weekday, hour, minutes, seconds
- Schedule events or alarms
- Automatically switches between main power and backup power
- High accuracy clock - within 30 seconds per year
- PiicoDev Connector, compatible with Qwiic and STEMMA QT (3.3V Only)
|
COMING SOONThis item is arriving soon. |
The PiicoDev Precision Temperature Sensor features a low-power, high precision TMP117 with 16-bit resolution and an accuracy of ±0.1°C (across -20°C to +50°C) with no calibration required. |
 |
SA0915 NEW
|
|
- Switch Type: SPST microswitch
- Connection: 6.3mm spade
- Illumination: 5-12V input
- Max material thickness: 30mm
- Mounting Hole: 27.5mm
- Mounting depth: 61mm
|
|
Ideal for use in retro gaming projects or anywhere a jumbo momentary switch may be required. |
 |
SA0914 NEW
|
|
- Switch Type: SPST microswitch
- Connection: 6.3mm spade
- Illumination: 5-12V input
- Max material thickness: 30mm
- Mounting Hole: 27.5mm
- Mounting depth: 61mm
|
|
Ideal for use in retro gaming projects or anywhere a jumbo momentary switch may be required. |
 |
SA0913 NEW
|
|
- Switch Type: SPST microswitch
- Connection: 6.3mm spade
- Illumination: 5-12V input
- Max material thickness: 30mm
- Mounting Hole: 27.5mm
- Mounting depth: 61mm
|
|
Ideal for use in retro gaming projects or anywhere a jumbo momentary switch may be required. |
 |
SA0912 NEW
|
|
- Switch Type: SPST microswitch
- Connection: 6.3mm spade
- Illumination: 5-12V input
- Max material thickness: 30mm
- Mounting Hole: 27.5mm
- Mounting depth: 61mm
|
|
Ideal for use in retro gaming projects or anywhere a jumbo momentary switch may be required. |
 |
SA0911 NEW
|
|
- Switch Type: SPST microswitch
- Connection: 6.3mm spade
- Illumination: 5-12V input
- Max material thickness: 30mm
- Mounting Hole: 27.5mm
- Mounting depth: 61mm
|
|
Ideal for use in retro gaming projects or anywhere a jumbo momentary switch may be required. |
 |
SA0910 NEW
|
|
- Switch Type: SPST microswitch
- Connection: 6.3mm spade
- Illumination: 5-12V input
- Max material thickness: 30mm
- Mounting Hole: 27.5mm
- Mounting depth: 61mm
|
|
Ideal for use in retro gaming projects or anywhere a jumbo momentary switch may be required. |
 |
Z6302K NEW
|
|
- Broadcom BCM2712 quad-core Arm Cortex A76 processor @ 2.4GHz
- RAM variants up to 8GB
- Interchangeable Camera and DSI display connectors
- Dual 4Kp60
- Real-time clock
- Power button
- UART debug port
|
|
The Raspberry Pi 5 8GB single board computer. The bandwidth speed and performance of the new Raspberry Pi 5 is a step up from earlier models. |
|
Z6302J NEW
|
|
- Broadcom BCM2712 quad-core Arm Cortex A76 processor @ 2.4GHz
- RAM variants up to 8GB
- Interchangeable Camera and DSI display connectors
- Dual 4Kp60
- Real-time clock
- Power button
- UART debug port
|
|
The Raspberry Pi 5 4GB single board computer. The bandwidth speed and performance of the new Raspberry Pi 5 is a step up from earlier models. |
 |
Z6421B NEW
|
|
- RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom
- Dual-core ARM Cortex M0 processor, flexible clock running up to 133 MHz
- 264kB of SRAM, and 2MB of on-board Flash memory
- Castellated module allows soldering direct to carrier boards
- USB 1.1 Host and Device support
- Low-power sleep and dormant modes
- Drag & drop programming using mass storage over USB
- 26 multi-function GPIO pins
- 2×SPI, 2×I2C, 2×UART, 3×12-bit ADC, 16×controllable PWM channels
- Accurate clock and timer on-chip
- Temperature sensor
- Accelerated floating point libraries on-chip
- 8×Programmable IO (PIO) state machines for custom peripheral support
|
|
Raspberry Pi Pico is a tiny, fast, and versatile board built using RP2040, a brand new microcontroller chip designed by Raspberry Pi in the UK. |
 |
Z6589 NEW
|
|
- Intuitive output: Air Quality Index
- Measures VOCs and eCO2
- A great guide to get you started
- PiicoDev connector, compatible with Qwiic and STEMMA QT (3.3V only)
- 2.54mm breakout for breadboarding/prototyping
- Manufactured and supported in Australia by Core Electronics
|
|
PiicoDev ENS160 Air Quality Sensor. Measure indoor air-quality - sensitive to fumes, cooking smells, humans. |
 |
K8600A NEW
|
|
- Simple set up - get printing within 20 minutes.
- Worry free automatic levelling.
- Easy to understand user interface with colour display.
- Auto filament loading and unloading.
- Direct extrusion for most common filament types.
- Ultra stable design with rigid dual Z-axis.
- Compact design fits easily on the workbench.
- Standard 0.4mm nozzle.
- 220 x 220 x 250mm build volume.
|
|
The Ender-3 V3 SE 3D printer is an enhanced and upgraded version of Creality's hugely popular Ender 3 platform. Creality have built in more features and optimisation for an intuitive and efficient FDM 3D printing experience. This Ender 3 has been tailored for those wanting a no compromises approach to features. |
 |
Z6296 NEW
|
|
|
|
Get your brand new Raspberry Pi Zero 2 W with most of the essentials in this kit. |
 |
X3063 NEW
|
|
- 2.4G remote control, suitable for indoor and outdoor flight, can be played in the bedroom.
- Equipped with high-precision gyro control
- With landing gear, can take off in a short distance.
- Has lights on the bottom.
- Mini size, small turning radius for indoor flight.
- High and low-speed modes
- Very easy to control. Slow indoor flight, fast outdoor flight, with adjustable flight attitude structure at the tail.
- Can perform rolling stunts.
- Can perform leaf fall drifting
- Can perform cobra aerobatic flight.
|
|
Experience the thrill of flying with this remote control plane! This ingeniously designed plane operates at 2.4GHz, featuring a double-wing design for precise speed control and optimal flight stability. |
 |
X3062 |
|
- Rider included
- Left/Right Turning
- Variable Speed
- Built-in 3.7V Lithium Battery
- Micro USB Charging lead included
|
|
Your kids will have lots of fun with this 2.4GHz remote control motorbike. Not only can it swing left and right but it also features variable speed. |
 |
X3061 NEW
|
|
|
|
Barrel up rough terrain with this remote control dune buggy thats perfect for small kids and big kids! 1:43 scale. |
 |
K8673 NEW
|
|
- Build more than 200 robots from simple to complex, which contains a lot of robot knowledge such as machinery, gears, structure, transmission, etc.
- Both Children and parents will enjoy the fun of building a robot and making a programming for it.
- Helps develop children's mind, DIY and logical thinking ability.
- Set is equipped with 47 robotics courses for kids to learn how to build, control and code at home while playing with this toy set.
- Incorporates 2 integrated motors and 2 IR sensors (batteries NOT included) to allow for intelligent, smooth moving robotic projects
- Allows kids to explore grow their imaginations by building and creating projects by themselves
- With the Makerzoid App from App Store and Google Play, kids can assemble the robots easily through the graphic instructions and control the motorized robot to move in all directions with the robotics kit.
- Available through the free app, Scratch 3.0 reduces the difficulty of coding - just to drop a few orders into the "Coding" section then the robot can react on your demand.
- The set is packed in a big storage box to help children develop a good habit of packing and collecting their own toys. And the sorting plate will be less time-consuming because kids could organize the building blocks based on the colour and size.
|
|
Build up to 200 different projects or create your own! Great for inspiring kids to invent and design with staged learning from the basics up to advanced Scratch programming. Each set contains hundreds of blocks, plus multifunction sensors, programmable motor and host controller. Compatible with big brand name blocks.
|
 |
K8672 NEW
|
|
- Build more than 100 robots from simple to complex, which contains a lot of robot knowledge such as machinery, gears, structure, transmission, etc.
- Both Children and parents will enjoy the fun of building a robot and making a programming for it.
- Helps develop children's mind, DIY and logical thinking ability.
- Set is equipped with 23 robotics courses for kids to learn how to build, control and code at home while playing with this toy set.
- Incorporates 2 integrated motors and 2 IR sensors (batteries NOT included) to allow for intelligent, smooth moving robotic projects
- Allows kids to explore grow their imaginations by building and creating projects by themselves
- With the Makerzoid App from App Store and Google Play, kids can assemble the robots easily through the graphic instructions and control the motorized robot to move in all directions with the robotics kit.
- Available through the free app, Scratch 3.0 reduces the difficulty of coding - just to drop a few orders into the "Coding" section then the robot can react on your demand.
- The set is packed in a big storage box to help children develop a good habit of packing and collecting their own toys. And the sorting plate will be less time-consuming because kids could organise the building blocks based on the colour and size.
|
|
The Robot Master sets supports the building of up to 200 different robotic projects from simple to complex, allowing kids to progress their STEM skills up with staged lessons. |
 |
K8671 NEW
|
|
- Build more than 72 robots from simple to complex, which contains a lot of robot knowledge such as machinery, gears, structure, transmission, etc.
- Enhance children's hand-on ability, DIY and logical thinking ability
- Different combinations of the motor and sensors greatly stimulate kids' to think scientifically.
- The control module of this educational toy also known as the "Intelligent Motor", contains 2 operation modes:"Electrical Mode" and "Intelligent Mode". The electric part makes it an excellent and amusing toy while the intelligent part is what specifically makes it SMART and DIFFERENT. (Batteries NOT included).
- Both the blocks and motor are compatible with almost all building sets. Spectacularly, with the great compatibility of the Intelligent Motor, it can power up motionless robots and make them move!
- Allows kids to explore grow their imaginations by building and creating projects by themselves
- With the Makerzoid App from App Store and Google Play, kids can assemble the robots easily through the graphic instructions and control the motorized robot to move in all directions with the robotics kit.
- Available through the free app, Scratch 3.0 reduces the difficulty of coding - just to drop a few orders into the "Coding" section then the robot can react on your demand.
- This set is packed in a storage box to help children develop a good habit of packing and collecting their own toys.
|
|
This 300pc set contains the parts for 72 different project designs which can be built using Makerzoids 3D app tutorials. |
 |
K8670 NEW
|
|
- Over 26 robots can be assembled as well as custom projects
- Incorporates 2 integrated motors and 2 IR sensors (batteries NOT included) to allow for intelligent, smooth moving robotic projects
- Allows kids to explore grow their imaginations by building and creating projects by themselves
- With the Makerzoid App from App Store and Google Play, kids can assemble the robots easily through the graphic instructions and control the motorized robot to move in all directions with the robotics kit.
- Available through the free app, Scratch 3.0 reduces the difficulty of coding - just to drop a few orders into the "Coding" section then the robot can react on your demand.
- Superbot brings you endless fun in building, playing then battling with their car models together which makes it the new pop in any kids' theme party.
- The set is packed in a clear storage box to help children develop a good habit of packing and collecting their own toys.
|
|
A 400pc set allowing kids to build up to 26 different projects, and create designs of their own. Includes control unit and intelligent sensors (2) that allow building of line tracking, obstacle avoiding and following robot designs. Blocks are compatible with other major brands. Fully programmable using Scratch. Includes storage box. |
 |
Z6381A |
|
- Adopts industrial chip esp8266, esp-12f module with metal shielding Case, strong Anti-slip potential;
- Used as an independent commission for the development of esp8266, uploading an official to the team Firmware, open source nodemcu, etc.
- Can also be used as an independent development board for Arduino, use the same as Arduino Development Board.
|
|
An Arduino compatible development board featuring WiFi making it ideal for plug-and-play projects.The board also features its GPIO broken out, a full USB-serial interface, NodeMCU pre-flashed and a power supply all on the one breadboard-friendly package. |
 |
Z6320X |
|
- Full range temperature compensated
- Relative humidity and temperature measurement
- Calibrated digital signal
- Outstanding long-term stability
- Extra components not needed
- Long transmission distance
- Low power consumption
- 4 pins packaged and fully interchangeable
|
|
Voltage: 5V
Temperature: -40~80'C, +/0.5
Humidity: 20~90%RH +/-2%RH
Suitable for Arduino SCM
A product for Arduino that works with official Arduino boards.
|
 |
Z6433 NEW
|
|
- XTensa dual-core 32-bit LX7 CPU, frequency up to 240MHz
- 2.4 GHz Wi-Fi, EEE 802.11 b/g/n-compliant
- Bluetooth, LE: Bluetooth 5, Bluetooth mesh
- 16 MByte(64Mbit) SPI Flash
- 384 KByte ROM
- 512 KByte SRAM
- 8 MByte(64Mbit) SPI PSRAM
- 16 KB SRAM in RTC
- Communication Interfaces: 2 x I2C, 2 x I2S, 4 x SPI, 3 x UART, 1 x USB OTG
- Security: 4096 bit OTP, AES, SHA, RSA, ECC and RNG, Secure boot, Flash encryption, Digital signature, HMAC module
- Dual Type-C USB connectors
- Reset and User/Firmware buttons
- RGB WS2812 User LED
- Power LED
- Virtual USB port provided by CP2102 for debugging and firmware upgrade
- Compact size of 50.1 x 13mm
- Supply Voltage: 5V via USB
- Circuit Voltage: 3.0 to 3.6V Circuit Operation
|
|
The ESP32-S3 development board is assembled with an original ESP32-S3-WROOM-1 module from Espressif, with 16MB Flash and 8MB PSRAM(ESP32-S3-WROOM-1-N16R8). It is a general-purpose Wi-Fi + Bluetooth® LE MCU module that integrates complete Wi-Fi and Bluetooth LE functions. |
 |
A0724 NEW
|
|
- Operating voltage: 12 V/DC (11 - 14 V)
- Power consumption: approx. 2 mA/35 mA (relay off/on)
- Relay contact: 1 x SWITCH OVER, loading capacity max. 25 V, 3 A
- Operating temperature range: approx. -15 to +50°C
- Luminous intensity switching-on: approx. 25 lux ±20%
- Luminous intensity switching-off: approx. 45 lux ±20%
- Switching delay: approx. 3 - 4 seconds
- Dimensions: approx. 72 x 50 x 32mm (without fastening straps, with sensor)
|
|
Kemo M122 switch allows users to switch lamps or other electric devices on or off at dusk or daybreak. The sensitivity of the luminous intensity may be changed by partially covering the sensor mechanically. |
 |
ZR6479 |
|
- Cable Type: MIPI DSI Adapter Cable
- Cable Length: 0.1m
- Colour: Orange
|
|
Connect a MIPI display to a ROCK single board computer with this MIPI DSI Display Adapter Cable. |
 |
ZR6474 |
|
- Cable Type: MIPI CSI Adapter Cable
- Cable Length: 0.1m
- Colour: Orange
|
|
Connect your ROCK board to a camera module with this MIPI CSI Camera Adapter Cable. |
 |
J0116 NEW
|
|
|
|
A plastic Mecanum wheel for robotics projects requiring omnidirectional movement. |
 |
J0115 NEW
|
|
|
|
A plastic Mecanum wheel for robotics projects requiring omnidirectional movement. |
 |
Z6382A NEW
|
|
- Dimensions: 32L x 25H x 24Wmm
- Sensor Outputs: Digital Output
- Required Supply Voltage: 5V - 20V
- Digital Output: 3.3V (High)
- Digital Output: 0V (Low)
- Quiescent Current: <50uA
- Delay Time: 0.5 - 200 Seconds
- Range 5m - 7m
- Angle Sensor: <100° cone angle
- Operating Temperature: -15°C to 70°C
- Lens size sensor: Ø23mm
|
|
When this motion sensor module is used in projects it can detect motion based on changes in infrared light in the environment. It is ideal to detect if a human has moved in or out of the sensor range. An LED will light up when movement is detected. This makes the module a great addition to security application projects. |
 |
Z6587 NEW
|
|
- Easy, wireless communication up to 100m
- Create your own network of connected devices.
- Compact, on-board antenna
- 915MHz is suitable for amateur use in Australia.
- No soldering necessary
- 2x LEDs: Rx/Tx indicator, and user-controllable
- PiicoDev connector, compatible with Qwiic and STEMMA QT (3.3V only)
- 2.54mm breakout for breadboarding/prototyping
|
|
With this Transceiver users can unlock some very cool capabilities like collecting data from some distant sensor, or remote-controlling hardware. |
 |
J0064 NEW
|
|
- Gear Ratio: 90:1
- Input Voltage: 12V
- No Load
- Speed: 66RPM
- Current: 0.3A
- Rated Load
- Speed: 50RPM
- Current: 1A
- Torque: 17kg-cm
- Stall Load
- Current: 3.8A
- Torque: 35kg-cm
|
|
This gearbox is suitable for a host of model and light industrial applications |
 |
ZR6302G |
|
- On board on/off power button
- Integrated fan control forthermal management
- Dual-display support
- Two micro-HDMI ports
- Supports display resolutions up to 4K @ 60hz (1 x 2K up to 1440P@60, 1 x 4K 2.0 up to 4k@60)
- Multiple connectivity capabilities so less add on hardware required, including Bluetooth 5.0 with BLE, Gigabit Ethernet & Wireless LAN
- A 40P GPIO expansion header provides extensive compatibility with a wide range of accessories
- Get more multiple memory options, including 4GB RAM and a speed eMMC socket
- Compatible with most R-Pi 4 accessories, including cases, cameras and HAT modules
|
|
The OKdo ROCK 4C+ is a reliable, multifunctional and high-performing single-board computer based on a robust Rockchip RK3399T SoC, Dual Cortex® A72 CPU and Arm Mali™ T860MP4 GPU. |
 |
Z6586 NEW
|
|
- Control up to four servos independently
- Daisy chain up to four Servo Drivers together for more complex projects
- No soldering necessary
- PiicoDev connector, compatible with Qwiic and STEMMA QT (3.3V only)
- 2.54mm breakout for breadboarding/prototyping
|
|
With this new servo driver users will be able to add the power of motion to projects. |
 |
K8601 NEW
|
|
- Double sided PEI coated plate
- Excellent flatness & elasticity
- Strong adhesion
- Durable and long lasting textured plate
|
|
Double sided black textured PEI spring steel magnetic build plate to suit 3D printer models K8600 & K8602 |
 |
Z6478 NEW
|
|
- Sensor size: 3.67 x 2.74 mm (1/4 format).
- Pixel count: 2592 x 1944.
- Pixel size: 1.4 x 1.4 um.
- Up to 90 fps video at vga.
- Sensor type: omnivision ov5647 color cmos qsxga (5-megapixel).
- Full-frame slr lens equivalent: 35 mm.
- Fixed focus: 1 m to infinity.
|
|
This camera module has been designed to be used with raspberry pi boards
|
 |
Z6584A NEW
|
|
- Measures acceleration and tilt
- Detect tapping, double-taps, and shaking
- Great guide to get you started
- PiicoDev connector, compatible with Qwiic and STEMMA QT (3.3V only)
- 2.54mm breakout for breadboarding/prototyping
|
|
The on-board LIS3DH can measure 16-bit acceleration data in ranges from 2g to 16g in all 3 axes. |
 |
Z6527A NEW
|
|
- Support Arduino Mega2560 Directly inserted
- With Full-angle IPS TFT panel
- On Board level conversion chip for 5V/3.3V MCU
- Compatible with 2.8~3.3V operation voltage level
- Compatible with Arduino-Series development Board.
- Provided 12-examples with Arduino ,3-examples with STM32
- With SD Card Socket
- With SPI FLASH circuit
|
|
A 480x320 display shield for the Arduino Mega utilising the ILI9486 chipset. Ideal for projects requiring sensor monitoring. |
 |
Z6367A NEW
|
|
|
|
Utilises the 44E hall effect sensor for contactless magnetic switching. Output drops to ground when triggered. 3.3-5V input. 36 x 22 x 7mm |
 |
Z6424 NEW
|
|
- RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom
- Dual-core Arm Cortex M0+ processor, flexible clock running up to 133 MHz
- 264KB of SRAM, and 2MB of on-board Flash memory
- USB 1.1 with device and host support
- Low-power sleep and dormant modes
- Drag-and-drop programming using mass storage over USB
- 26 × multi-function GPIO pins
- 2 × SPI, 2 × I2C, 2 × UART, 3 × 12-bit ADC, 16 × controllable PWM channels
- Accurate clock and timer on-chip
- Temperature sensor
- Accelerated floating-point libraries on-chip
- 8 × Programmable I/O (PIO) state machines for custom peripheral support
|
|
The Raspberry Pi Pico W is perfect for IoT and wireless projects, better still, it's such an affordable 32-bit microcontroller that is packed with peripheries including WiFi. |
 |
Z6516A NEW
|
|
- 7’’ standard display, 1024x600 resolution
- Capacitive touch screen, maximum support 5 point touch
- Supports backlight control, the backlight can be turned off to save power
- Supports standard HDMI interface input.
- Can be used as general-purpose-use HDMI monitor, for example: connect with a computer HDMI as the sub-display (resolution of the output has to be able to adjust to 800X480)
- Used as a Raspberry Pi display that supports Raspbian, Ubuntu, Kodi, win10 IOT, single-touch, free drive etc.
- Works as a PC monitor, support win7, win8, win10 system 5 point touch (XP and older version system: single-point touch), free drive.
|
|
A 1024x600 touchscreen for Raspberry Pi that supports standard HDMI interface input which can be directly connected to Raspberry Pi. |
 |
Z6421A |
|
- Ultra compact form factor
- Dual core ARM Cortex M0+ processor
- Two SPI controllers
- Two I2C controllers
- 16 PWM channels
- 26 multifunction GPIO pins
- Three analogue inputs
- On board USB controller
- In-built temperature sensor
- Castellated module allows soldering direct to carrier boards
- Drag-and-drop programming using mass storage over USB
- Low-power sleep and dormant modes
- Accurate on-chip clock
- Accelerated integer and floating-point libraries on-chip
- Includes headers
|
|
Raspberry Pi Pico is a tiny, fast, and versatile board built using RP2040, a brand new microcontroller chip designed by Raspberry Pi in the UK. From controlling appliances to operating a light display, Raspberry Pi Pico puts the technology that underpins countless everyday operations into your hands. |
 |
K-8600E |
|
|
|
Replacement power supply module to suit Creality Ender 3 3D printer. |
 |
K-8600D NEW
|
|
|
|
Replacement teflon bowden tubing to suit Creality Ender and other brands/types of 3D printer. 1m length. |
 |
K-8600C |
|
|
|
Replacement pneumatic connectors to suit Creality Ender 3. Includes extruder and hot end threaded fittings and tube clips. |
 |
K-8600B |
|
|
|
Standard replacement 0.4mm nozzle for Creality Ender 3 3D Printer, suitable for use on other brands/types of 3D FDM printers also. |
 |
K-8600A |
|
|
|
Standard replacement mainboard for Creality Ender 3 3D Printer. Board version V4.2.2. Note: This is not a silent version board. |
 |
Z6439B NEW
|
|
- On board speaker
- MEMs Microphone with LED indicator
- Touch sensitive logo
- Built-in sleep/off mode that means the board can be powered-down with batteries connected
- Discrete regulator that can supply up to 190mA of current to external accessories
- 25 Programmable LEDs in a 5 x 5 grid
- 3-axis motion sensing
- On-board magnetometer
- On-board temperature sensor
- On-board light level sensing
- 2 x programmable buttons, A & B
- BLE Bluetooth 5.0
- 2.4Ghz Micro:bit Radio
- Rear-mounted push button
- Power off (push and hold power button)
- 25 pins
- MEMS microphone and LED indicator
- Onboard speaker
- Touch-sensitive logo pin
- LED power indicator
- C++, MakeCode, Python, Scratch
|
|
The Micro:bit is easy to code with, all you need is your web browser and a micro USB cable and you are ready to start all kinds of exciting STEM/STEAM experiments, no need for any extra software to be installed. Micro:bit has also developed a mobile app for coding over Bluetooth (without a USB cable), that makes it even easier to get everyone codin |
 |
K8615 NEW
|
|
- 7.9" 4K mono LCD
- Self-developed integral light source
- High performance mainboard
- Z-axis with dual linear rails
- 5" HD touch screen
- Air filtration system
- Multiple slicing software
- Supports Creality Cloud APP
- Supports OTA updates
- Compatible with HALOT-BOX Lychee and CHITUBOX
|
|
The large 7.9" 4k mono LCD screen with a resolution of 4320*2560, vividly prints out every detail. With an upgraded 172 x 102 x 160mm build volume, it has a 73% volume increase compared to the 6" LCD and supports both smaller or larger models. |
 |
K8612 NEW
|
|
- 300°C high temp nozzle.
- 300 x 300 x 400mm build volume.
- HD monitor camera in-built.
- Wi-Fi, Bluetooth and Ethernet connectivity.
- Trapezoidal design for added stability on large volume prints.
- Wide compatability with a variety of filament including PLA, ABS, PVA, TPU, PA, PETG and wood.
- Full-metal dual gear direct extruder.
- CR Touch 16 point automatic levelling sensor or manual levelling as desired.
- LED light bar.
- Spring steel flexible magnetic build plate.
- Silent main board - no noisy stepper motors!
- Filament sensor.
- Pause/resume printing.
- Creality Cloud Printing with iOS/Android app support.
- Supplied mostly assembled to get you printing faster (assembles in under 30 mins).
|
|
The 7 module design of this high performance 3D printer enables assembly within 10 minutes. |
 |
K8610 NEW
|
|
|
|
This high performance 3D printer with a more aesthetic, streamlined design, features a brand new nozzle made of brass that can stand up to +300°C printing temperature and is compatible with PLA, ABS, PVA, TPU, PA, PETG and wood. |
 |
Z6370A |
|
- Wavelength: 650nm
- Output Power: <1mW
- Colour: Red
- Class: 3R
- Operating Voltage: 3.3-5 V (DC)
- Interface: 3 Pin
- Interface Input Signal: Digital
- Weight: 3.6g
- Board Size: 35 x 22 x 10 mm
|
|
The transmitter module of the KEYES laser transmitter is designed for Arduino. Its connection port is compatible with the Arduino Shield transmitter. |
 |
Z6388A |
|
- Module Type: Type C USB
- Charge Mode: Linear Charging
- Charge Current: 1A
- Charge Precision: 1.5 %
- Input Voltage: 4.5V ~ 5.5V
- Full Charged Voltage: 4.2V
- Led Indicator: Red is charging, Blue is fully charged
- Input Interface: Type C USB
- Work Temperature: -10℃~ 85℃
- Size: 28 x 17.5 x 4mm
- Weight: 1.8g
|
|
Provides a 1A charging current to a single lithium cell from a 5V DC input. |
 |
Z6409 |
|
- Electrical Specifications
- Supply Voltage: 8-26V DC
- Recommended Power Supply Current: 2A
- Output Power: 2x15W (@16V, 8RΩ)
- Size: 44mm x 40.5mm
- Audio Output
- Terminal: Speaker/s
- Impedance: 4 Ohms, 8 Ohms
- Recommended Power: 10W-20W
|
|
The TPA3110 chip on board this amplifier module provides a high output, lower power consumption audio solution with great audio quality too. |
 |
Z6407 |
|
- Electrical Specifications
- Supply Voltage: 8-26V DC
- Recommended Power Supply Current: 2A
- Output Power: 2x15W (@16V, 8RΩ)
- Size: 44mm x 40.5mm
- Audio Output
- Terminal: Speaker/s
- Impedance: 4 Ohms, 8 Ohms
- Recommended Power: 10W-20W
|
|
The TPA3110 chip on board this amplifier module provides a high output, lower power consumption audio solution with great audio quality too. |
 |
K2001 |
|
- 1x Double-Sided PCB - 71 x 40mm
- 1x Mini-USB Socket (CON1)
- OR
- 1x SMD coin cell holder (BAT1)
- Semiconductors
- 1x 7555 CMOS timer IC, SOIC-8 (IC1)
- 1x 4017B decade counter IC, SSOP-16
- (IC2)
- 1x 2N7002 N-channel Mosfet, SOT-23
- (Q1)
- 4x M3216/1206 size LEDs, any colour
- (LED1, LED6, LED11, LED12)
- 2x M2012/0805 size LEDs, any colour
- (LED2, LED7)
- 2x M1608/0603 size LEDs, any colour
- (LED3, LED8)
- 2x M1005/0402 size LEDs, any colour
- (LED4, LED9)
- 2x M0603/0201 size LEDs, any colour
- (LED5, LED10)
- Capacitors (all SMD X7R 10V+ ceramic)
- 1x 1μF M3216/1206 size
- 2x 100nF M3216/1206 size
- 4x K 2001SMD Trainer Kit
- Resistors (all SMD 1% or 5%)
- 2x 100kW M3216/1206 size
- 4x 1kW M3216/1206 size
- 2x 1kW M2012/0805 size
- 2x 1kW M1608/0603 size 2
- 1x 1kW M1005/0402 size 2
- 1x 1kW M0603/0201 size
|
|
This simple SMD Trainer project is a great way to practice soldering a variety of surface-mount devices. |
 |
K8650 |
|
- Up to 10.1 inch cleaning/curing capabilities
- Interactive interface
- 360° magnetic rotating platform
- Dual band UV lamp bead strip
- Selectable speed and time settings
|
|
Resin based 3D printers are rapidly becoming the go to tool for high resolution 3D prints. They offer a faster print process with excellent accuracy and a stronger finished product thanks to UV curing on each layer. |
 |
K8640 |
|
- Build volume up to 130 x 82 x 160mm
- Fast layer speed with each layer taking between 1 and 4 seconds.
- UV integrated light source
- 1620 x 2560 resolution
- Precision up to 51μm
- LCD HD screen
- Z-Axis linear rail for better stability
- Air filtration system
- Manual levelling system
- 3.5 inch full colour touch screen
|
|
Resin based 3D printers are rapidly becoming the go to tool for high resolution 3D prints. They offer a faster print process with excellent accuracy and a stronger finished product thanks to UV curing on each layer. |
 |
K8404 |
|
- Low-temperature filament
- High precision
- Good fluidity
- No bubbling
- Doesn't warp easily
|
|
Contains 10 different colours of 1.75mm PCL filament for use with our handheld printing pen. Each colour roll is approx 5m long. |
 |
K8496 |
|
- Low viscosity and good fluidity
- High printing accuracy
- Quick printing speed
- Wide range of applications
- Low shrinkage rate
|
|
Designed for use with resin printers this UV sensitive printing fluid provides excellent accuracy and detail for your prints. |
 |
K8495 |
|
- Low viscosity and good fluidity
- High printing accuracy
- Quick printing speed
- Wide range of applications
- Low shrinkage rate
|
|
Designed for use with resin printers this UV sensitive printing fluid provides excellent accuracy and detail for your prints. |
 |
K5158 |
|
- Low distortion and noise
- Easy to build
- Extremely compact PCB
- Fits on a 75mm heatsink
- Stackable in a 2U rack case
- Onboard DC Fuses
- Specified Power Output
- Over-current protection
- Overload Recovery
- Square Wave Response
- Short Circuit protection
- Quiescent Current Adjustment
- 100W RMS into 4 Ω
- 80W RMS into 8 Ω
|
|
This compact amplifier module kit packs a surprising punch for its size! |
 |
K8623 |
|
|
|
This Flexible Magnetic Plate provides an easy solution to cleaning up after printing with resin. |
 |
K8630 |
|
- Multi-point detection
- Smart compensation
- High precision
- Low power consumption
- Easy to install
- Strong compatibility
- Stable function
|
|
The CR-Touch Sensor has been designed as a leveling solution based on users feedback. |
 |
Z6427 |
|
|
|
A handy Wi-Fi activated relay module for Arduino and other development applications. |
 |
P1020A |
|
|
|
Designed specifically to fit between the headers of an 'Arduino Shield board' for easy prototyping. Standard 0.1 inch spacings. Accepts all ICs, transistors, diodes, LEDs and passives. Uses solid hook up wire for interconnections. |
 |
Z6597 |
|
- 200mm long
- Also compatible with Qwiic and STEMMA QT boards
- Reversible cable - if it fits it works!
|
|
This 200mm cable is for connecting PiicoDev modules together. |
 |
Z6596 |
|
- 100mm long
- Also compatible with Qwiic and STEMMA QT boards
- Reversible cable - if it fits it works!
|
|
This 100mm cable is for connecting PiicoDev modules together. |
 |
Z6591 |
|
- Rapid prototyping with solderless connections
- Other useful pins are broken out
- PiicoDev connector, compatible with Qwiic and STEMMA QT (3.3V only)
|
|
The PiicoDev® Adapter for Raspberry Pi is a great way to connect sensors to your Raspberry Pi. |
 |
Z6590 |
|
- Connect new sensors to your Micro:bit
- No soldering necessary
- Crocodile clip connections are broken out again, so you can still hand wire to your Micro:bit
- PiicoDev connector, compatible with Qwiic and STEMMA QT (3.3V only)
|
|
Connect your Micro:bit with the outside world using PiicoDev® Adapter for Micro:bit. With this adapter you can experiment with sensors from the PiicoDev range giving your Micro:bit new sensing abilities. |
 |
Z6585 |
|
- Accurate air pressure measurements
- PiicoDev connector, compatible with Qwiic and STEMMA QT (3.3V only)
- 2.54mm breakout for breadboarding/prototyping
|
|
Our PiicoDev® Pressure Sensor is perfect for measuring barometric pressure or inferring altitude from air pressure. |
 |
Z6584 |
|
- Measure linear and angular motion
- Detect free fall or bumps/knocks
- PiicoDev connector, compatible with Qwiic and STEMMA QT (3.3V only)
- 2.54mm breakout for breadboarding/prototyping
|
|
Our PiicoDev® Motion Sensor makes it super easy to detect linear or angular motion in your next project. |
 |
Z6583 |
|
- Small size, millimetre precision
- Can be protected behind many cover-window materials.
- PiicoDev connector, compatible with Qwiic and STEMMA QT (3.3V only)
- 2.54mm breakout for breadboarding/prototyping
|
|
The PiicoDev® Distance Sensor is a long-distance laser-ranging sensor that uses Time-of-Flight (ToF) to accurately measure distances up to 4m. |
 |
Z6582 |
|
- Small size, high accuracy
- PiicoDev connector, compatible with Qwiic and STEMMA QT (3.3V only)
- 2.54mm breakout for breadboarding/prototyping
|
|
The PiicoDev® Ambient Light Sensor is a great solution for sensing ambient light levels. |
 |
Z6581 |
|
- Measure temperature, pressure and relative humidity
- PiicoDev connector, compatible with Qwiic and STEMMA QT (3.3V only)
- 2.54mm breakout for breadboarding/prototyping
|
|
The PiicoDev® Atmospheric Sensor allows you to easily measure barometric pressure, humidity, and temperature. Use it to build your own weather station or perform experiments. |
 |
Z6580 |
|
- Small size, high accuracy
- PiicoDev connector, compatible with Qwiic and STEMMA QT (3.3V only)
- 2.54mm breakout for breadboarding/prototyping
|
|
The PiicoDev Precision Temperature Sensor features a low-power, high precision TMP117 with 16-bit resolution and an accuracy of ±0.1°C (across -20°C to +50°C) with no calibration required. |
 |
Z6425A |
|
- Fan Control
- Built in current sensor
- Built in brushless fan
- Fully isolated power supply
- 4 x spacers included
|
|
Enables simultaneous communication with the LAN network and power supply of the Raspberry Pi board. |
 |
H8952A |
|
- Sleek minimal design
- 2 x Standard 'type A' HDMI ports
- Aluminium Alloy top for passive cooling
- Programmable 30mm fan
- Clean Power Shutdown
- Multi-function power button
- Power management modes (with Always ON)
- Magnetic top access to GPIO pins
- Colour coded GPIO pins
- Easy installation
|
|
This Raspberry Pi 4 Argon ONE V2 Case not only has brilliant passive cooling (the whole top part of the case is a heatsink) but also protects the Raspberry Pi without compromising the full functionality of the motherboard. |
|
Z6439A |
|
- On board speaker
- MEMs Microphone with LED indicator
- Touch sensitive logo
- Built-in sleep/off mode that means the board can be powered-down with batteries connected
- Discrete regulator that can supply up to 190mA of current to external accessories
- 25 Programmable LEDs in a 5 x 5 grid
- 3-axis motion sensing
- On-board magnetometer
- On-board temperature sensor
- On-board light level sensing
- 2 x programmable buttons, A & B
- BLE Bluetooth 5.0
- 2.4Ghz Micro:bit Radio
- Rear-mounted push button
- Power off (push and hold power button)
- 25 pins
- MEMS microphone and LED indicator
- Onboard speaker
- Touch-sensitive logo pin
- LED power indicator
- C++, MakeCode, Python, Scratch
|
|
The Micro:bit is easy to code with, all you need is your web browser and a micro USB cable and you are ready to start all kinds of exciting STEM/STEAM experiments, no need for any extra software to be installed. Micro:bit has also developed a mobile app for coding over Bluetooth (without a USB cable), that makes it even easier to get everyone codin |
 |
K9701 |
|
- Altronics kits are premium do-it-yourself projects designed to be assembled with ease. However, basic electronics knowledge and soldering skills are essential to construct our kits. A difficulty rating is provided to help determine if your ability is sufficient to build the kit project. Please note, once assembly has been commenced we are unable to honor any warranty claims. Please see the full details here.
|
|
The PT2329 is an audio processor IC consisting of a stereo input selector along with volume and tone controls, all controlled through I2C. |
 |
K8622 |
|
|
|
Creality FEP Release Film for LCD SLA Resin 3D Printer |
