|
Description |
Downloads |
Specs |
Ordering |
|
 |
Z6435 |
|
- Microcontroller Atmel ATmega32U4
- Touch IC Resurgent Semiconductor MPR121
- MP3 decoder IC VLSI Solution VS1053b
- Audio output 15mW into 32Ω via 3.5mm stereo socket
- Removable storage up to 32GB via micro SD card
- Input voltage 3.0V DC – 5.5V DC
- Operating voltage 5V DC
- Max. output current (5V rail) 400mA (100mA at startup)
- Max. output current (3.3V rail) 300mA
- LiPo cell connector 2-way JST PH series - pin 1 +ve, pin 2 -ve
- LiPo charge current 200mA
- Capacitive touch electrodes 12 (of which 8 can be configured as digital I/O)
- Digital I/O Pins 20 (of which 3 are used for the MPR121 and 5 are used for the VS1053b — the latter can be unlinked via solder blobs)
- PWM channels 7 (shared with digital I/O pins)
- Analogue input channels 12 (shared with digital I/O pins)
- Flash memory 32 kB (ATmega32U4) of which 4kB used by boot loader
- SRAM 2.5kB (ATmega32U4)
- EEPROM 1kB (ATmega32U4)
- Clock speed 16MHz (ATmega32U4), 12.288MHz (VS1053b)
- DC current per I/O pin 40mA sink and source (ATmega32U4), 12mA source / 1.2mA sink (MPR121)
- Analogue input resistance 100MΩ typical (ATmega32U4)
|
|
The Touch Board is a microcontroller board with dedicated capacitive touch and MP3 decoder ICs. It has a headphone socket and micro SD card holder (for file storage), as well as having 12 capacitive touch electrodes. It is based around the ATmega32U4 and runs at 16MHz from 5V. It has a micro USB connector, a JST connector for an external lithium po |
 |
K9655 |
|
- Standard Australian electrical wallplates (two facia covers provided)
- atMega328p microcontroller
|
|
Developed in house by Altronics, the Inventa Maker Plate was developed to bring Arduino into the home automation sector by incorporating it with standard Australian electrical wallplates. 16x2 LCD Shield. |
 |
X3035 |
|
|
|
Create your own family world cup with these fun football
robots. 2 players included with pitch (1m x 0.8m), goals, ball and cones. |
 |
K8630 |
|
- Multi-point detection
- Smart compensation
- High precision
- Low power consumption
- Easy to install
- Strong compatibility
- Stable function
|
|
The CR-Touch Sensor has been designed as a leveling solution based on users feedback. |
 |
K5315 |
|
- Channels: two
- Equaliser bands: seven (63Hz, 160Hz, 410Hz, 1kHz, 2.5kHz, 6.2kHz, 16kHz)
- Boost/cut: approximately ±12.5dB (bands overlap; see Fig.1) Signal-to-noise ratio: 108dB (2V RMS), 102dB (1V RMS)
- Total harmonic distortion: <0.0005%, 20Hz-20kHz, 20Hz- 22kHz bandwidth (see Fig.2)
- Input impedance: 100kΩ
- 100pF Output impedance: 470Ω
- The power supply as supplied supports 18-24V for the DC option, not 12-24V
- Channel separation: >50dB, 20Hz-20kHz (>=80dB 20Hz-1kHz)
- Other features: compact design, uses rotary pots for easy panel mounting
|
|
This stereo version of Silicon Chip’s new equaliser is perfect for new and existing home Hi-Fi systems. It features extremely low noise and distortion, so it won’t degrade your signal. Multiple methods of powering the unit make fitting it into an existing system a breeze. |
 |
K9300 |
|
- Contactless operation
- 90-100mm detection range
- No batteries (in tags) to go flat
- Stores up to 24 tag ID codes
- Easy tag addition & removal
- Works through any non-metallic material
- Audio feedback via on-board beeper
- Tamper detection
- Arm & alarm outputs
- Electric door strike output
- Suitable for home or car use
- Requires 12V DC @ 40mA (nominal)
|
|
Essentially, the system consists of a reader module and one or more "tags". Based on RFID (Radio Frequency Identity) technology, each tag is encoded with a unique identity. When a tag is brought within range of th |
 |
K2220 |
|
- Battery: 3 x AA
- Box Size: 370x320x120 mm
- Weight: 1400 grams approx
|
|
The new K 2220 Electronic Digital Recording Project Lab Kit makes a great introduction to the world of Advanced Electronic Digital Recording Technology. |
 |
K5255 |
|
- Altronics kits are premium do-it-yourself projects designed to be assembled with ease. However, basic electronics knowledge and soldering skills are essential to construct our kits. A difficulty rating is provided to help determine if your ability is sufficient to build the kit project. Please note, once assembly has been commenced we are unable to honor any warranty claims. Please see the full details here.
|
|
Up to 12 K5250 Intercom Sub-stations can be used from this one power supply. |
 |
Z6311 |
|
|
|
A huge array of sensors for building into your Arduino project design. All feature standard pin headers for easy connection. The kit includes boards such as 1 channel relay, joystick, temp/humidity sensor, rotary encoder, microphones, hall effect sensor and much more! |
 |
Z6244 |
|
- A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock.
- CPU Clock at 84MHz.
- 96KB of SRAM.
- 512KB of Flash memory for code.
- A DMA controller that can relieve the CPU from doing memory intensive tasks.
|
|
The Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU. It is the first Arduino board based on a 32-bit ARM core microcontroller. |
 |
Z6454 |
|
- Works with BBC Micro:bit
- Micro:bit slot allows students to adjust and test code revisions
- Ideal for classroom & STEM workshop environments
- RGB LED light ring
- Easy wiring and construction
- Infra-red and ultrasonic based avoidance
- Line tracking capability
- Photo cell for light intensity detection
- Powered by long life 18650 lithium cells
- Bluetooth controllable
|
|
STEM bot is an easy to program 2 wheel obstacle avoidance and line tracking robot. Coding your program is easy using the standard BBC Micro:bit software. Wiring and construction has been designed to be as simple as possible. |
 |
H8930 |
|
- Supports a single SSD drive
- Accepts M.2 SSD NGFF Key B and Key B+M
- SSD Size: NGFF M.2 2280 2260 2242 2230
- Chipset: ASMedia Technologies - ASM1153E
- Compliant with USB3.0 Specification Revision 1.0
- Up to 6Gbps transfer speeds
- 2 Standard (type A) HDMI Ports
- Aluminium Alloy Top for Passive Cooling
- Programmable 30mm Fan
- Programmable IR Receiver
- Clean Power Shutdown
- Multi-Function Power Button
- Power Management Modes (with always ON)
- Magnetic Top Access to GPIO Pins
- Colour Coded GPIO Pins
- Easy Installation
|
|
A R-Pi 4 enclosure supporting one M.2 SATA SSD drive, plus two full size HDMI ports, power management modes and built in IR control support. Features both active and passive cooling from an internal fan and aluminium heatsinking case. |
 |
Z6560 |
|
- 11 levels of speaking speed
- Supports Chinese and english languages
- Both male and female voice supported
- Use the Serial ports of your Arduinos only
|
|
This Speech Synthesis Shield is designed to be easily stacked upon any standard arduinos. It uses a XFS5051CE speech synthesis chip from IFLYTEK which combines world leading technology and high degree of integration. |
 |
Z6423 |
|
- Sony IMX477R stacked, back-illuminated sensor, 12.3 megapixels, 7.9 mm sensor diagonal, 1.55 μm × 1.55 μm pixel size
- Ouput: RAW12/10/8, COMP8
- Back focus: Adjustable (12.5 mm–22.4 mm)
- Lens standards: C-mount, CS-mount (C-CS adapter included)
- IR cut filter: Integrated
- Ribbon cable length: 200 mm
- Tripod mount: 1/4”-20
|
|
The latest Raspberry Pi camera now with support for C/CS mount lenses so you can set your camera to whichever focal length you desire. 12.3 megapixel Sony® sensor. Ideal for home surveillance and monitoring projects. |
 |
K2574 |
|
|
|
(SC April '04) Allows quick "in-circuit" detection of defective electrolytic capacitors. 0.01-99Ω autoranging. Includes case & fully screened & punched front panel. |
 |
K5181 |
|
- High efficiency
- high power
- Low distortion and noise
- Bridging option for driving 8Ω loads with two modules
- Over-current protection
- Over-temperature protection
- Under-voltage switch-off
- Over-voltage switch-off
- DC offset protection
- Fault indicator
- Amplifier running indicator
- Optional speaker protector module
|
|
(SC Nov '12) This high specced power amplifier operates in Class 'D' as opposed to earlier amplifiers which run in the more conventional Class 'AB' or Class 'A'. The new Class 'D' amplifier offers the extrem |
 |
K2206 |
|
|
|
These simple kits are a great introduction to the world of electronics. Basic principles are covered and assembly is completely solderless using a series of spring loaded terminals. |
 |
Z6310 |
|
|
|
A parts kit for people interested in learning working with Arduino powered designs. It includes an Arduino UNO compatible board, proto-shield, dot matrix LED module, 7 segment displays, two breadboards, stepper motor, servo, IR remote, connection leads, battery box and a variety of components, LEDs, buttons and sensors. |
 |
K-8600A |
|
|
|
Standard replacement mainboard for Creality Ender 3 3D Printer. Board version V4.2.2. Note: This is not a silent version board. |
 |
K8671 NEW
|
|
- Build more than 72 robots from simple to complex, which contains a lot of robot knowledge such as machinery, gears, structure, transmission, etc.
- Enhance children's hand-on ability, DIY and logical thinking ability
- Different combinations of the motor and sensors greatly stimulate kids' to think scientifically.
- The control module of this educational toy also known as the "Intelligent Motor", contains 2 operation modes:"Electrical Mode" and "Intelligent Mode". The electric part makes it an excellent and amusing toy while the intelligent part is what specifically makes it SMART and DIFFERENT. (Batteries NOT included).
- Both the blocks and motor are compatible with almost all building sets. Spectacularly, with the great compatibility of the Intelligent Motor, it can power up motionless robots and make them move!
- Allows kids to explore grow their imaginations by building and creating projects by themselves
- With the Makerzoid App from App Store and Google Play, kids can assemble the robots easily through the graphic instructions and control the motorized robot to move in all directions with the robotics kit.
- Available through the free app, Scratch 3.0 reduces the difficulty of coding - just to drop a few orders into the "Coding" section then the robot can react on your demand.
- This set is packed in a storage box to help children develop a good habit of packing and collecting their own toys.
|
|
This 300pc set contains the parts for 72 different project designs which can be built using Makerzoids 3D app tutorials. |
 |
K-8600E |
|
|
|
Replacement power supply module to suit Creality Ender 3 3D printer. |
 |
K6027 |
|
- Altronics kits are premium do-it-yourself projects designed to be assembled with ease. However, basic electronics knowledge and soldering skills are essential to construct our kits. A difficulty rating is provided to help determine if your ability is sufficient to build the kit project. Please note, once assembly has been commenced we are unable to honor any warranty claims. Please see the full details here.
|
|
This MPPT charge/Light controller will work with 12V or 24V solar panels to charge a 12V or 24V lead-acid or lithium iron phosphate battery. you can then use the battery to run 12V dc lighting. |
 |
K5804 |
|
- LED voltage: 12-24V DC
- LED current: up to 10A total (ie, 120-240W maximum)
- Number of LED strings: up to 16 per unit
- LED control method: PWM, 200Hz, 255 brightness steps
- LED connectors: 2-pin or 4-pin male headers, 2.54mm pitch
- Audio input: 0.5-2.2V RMS nominal, 180kΩ 100pF input impedance
- Audio output: 1.1V RMS, THD+N 0.004%, signal-to-noise ratio 100dB
- Audio file support: 8-48kHz 16-bit mono or stereo WAV files
- Maximum directory depth: eight levels
- Maximum files per directory: 100
- Control method: universal infrared remote (optional)
- Dimensions: 140 x 110 x 35mm
- Supply voltage: 12-24V DC
- Current drain: ~110mA at 12V
|
|
(SC Oct/Nov '12) Accepts audio input signals and drives coloured LEDs "in tune" with the music. 16 output channels respond to different audio frequency bands and the light brightness is in proportion to the |
 |
Z6314 |
|
|
|
Includes an Arduino UNO compatible board, proto-shield, alphanumeric LCD, dot matrix LED module, 7 segment displays, two breadboards, stepper motor, servo, battery box and other components. |
 |
Z6513 |
|
- 5’’ standard display, 800 × 480 resolution
- With resistive touch screen, support touch control
- Supports backlight control, the backlight can be turned off to save power
- Supports standard HDMI interface input, compatible with and can be directly connected to Raspberry Pi (3rd, 2nd, and 1st generation)
- Can be used as general-purpose-use HDMI monitor, for example: connect with a computer HDMI as the sub-display (resolution need to be able to force output for 800 x 480)
- Used as a Raspberry Pi display that supports Raspbian, Ubuntu, Kodi, win10 IOT (resistive touch)
- Work as a PC monitor, support XP,win7, win8, win10 system(do not support touch)
|
|
A 800 x 480 touchscreen for Raspberry Pi that supports standard HDMI interface input, compatible with and can be directly connected to Raspberry Pi (3rd, 2nd, and 1st generation). |
