|
Description |
Downloads |
Specs |
Ordering |
|
|
A4285C |
|
- VU meter on LCD screen
- Output peak limited
- Multi-stage thermally cued fan cooling
- 2U 19" rack mount
- Tape record out terminals
- Remote volume facility
- Optional alert, evac & chime tone generator (A 4573)
- Vox activated 24V dc output
- 6 inputs with 3 pin XLR or 2 x RCA sockets
- Phantom powering available on all inputs
- Three levels of priority
- Option for mic/line to operate vox muting on inputs 1 to 3
- Push to talk (PTT) terminals on rear panel
- Bass and treble tone controls
- Power amp line out connector
- Terminals for 100V line, 70V line and 4 - 16Ω loads
- 240V ac or 24V dc power operation
- Thermal & fuse overload protection
- Built in short circuit protection
- 300mA trickle charge facility for 24V dc batteries
- Master volume can be configured as pre or post line out
|
|
Engineered for professional PA installations, the A 4285B conservatively delivers 250W RMS power. Including three levels of input priority, bass and treble controls and phantom powering capability enable unparalleled flexibility for a wide scope of applications such as schools, shopping centres, workshops, mine sites and office buildings. |
|
A3051 |
|
|
|
A low noise pre-amplifier with RIAA equalisation circuitry for connecting your turntable up to a standard auxillary input on a mixer or amplifier. Suitable for use with 'Moving Magnet' pickups. powered by a 9V battery. Compact design fits easily behind an |
|
A3052 |
|
- For all turntables with moving magnet (MM) cartridges or audio devices with line level (e.g. tape decks)
- External housing, reliably shielded against interference
- Top quality circuit technology and components
- Built-in low-noise phono preamp circuit conforms to the RIAA standard
- Power supply included
|
|
This phono preamp can be used to raise your turntable's output to make it compatible with modern amplifiers. At the same time, it adds standardised equalisation. Users may need this phono preamp because their turntable either doesn't have one, in which case they won't be able to play records without one. |
|
C7215 |
|
|
|
Bag to suit Okayo portable PA models, C7206, C7207 and C7210. |
|
A4476 |
|
- Remote preset selection
- Cat5e connection
- LCD indicates presets available
|
|
The A4476 wallplate is used to provide local access to presets programmed into the A4480B. |
|
C0388 |
|
- Polar Pattern: Unidirectional (cardioid)
- Impedance: 250 Ohm
- Sensitivity: -72dB ±3dB
- Frequency Response: 60Hz-16kHz
|
|
This excellent professional dynamic microphone is suitable for the most demanding vocal applications. It allows performers to deliver vocal power and clarity even in the most acoustically adverse venues. |
|
A6540 |
|
- User programmable buttons & icons
- Multiple screen pages (12 max)
- Tandem operation
- Event splash screens
- Icon library for commonly used buttons
- Infra-red control output
- RS-232 or RS-485 serial outputs
- PIR motion trigger
- Haptic & audible button feedback options
- U/UTP Cat5 cable connection
- Multi-command macros
- IR learning facility
- SD card configuration upload
- Easy to program
|
|
This universal touchscreen wallplate is the perfect control system for commercial and domestic automation. Its stylish low profile design lends itself to installation in new modern homes, classrooms, lecture theatres or corporate boardrooms. |
|
A6541 NEW
|
|
- User programmable buttons & icons
- Multiple screen pages (12 max)
- Tandem operation
- Event splash screens
- Icon library for commonly used buttons
- Infra-red control output
- RS-232 or RS-485 serial outputs
- PIR motion trigger
- Haptic & audible button feedback options
- U/UTP Cat5 cable connection
- Multi-command macros
- IR learning facility
- SD card configuration upload
- Easy to program
|
|
This universal touchscreen wallplate is the perfect control system for commercial and domestic automation. Its stylish low profile design lends itself to installation in new modern homes, classrooms, lecture theatres or corporate boardrooms. |
|
A6530 NEW
|
|
- User programmable buttons & icons
- Multiple screen pages (12 max)
- Tandem operation
- Event splash screens
- Icon library for commonly used buttons
- Infra-red control output
- RS-232 or RS-485 serial outputs
- PIR motion trigger
- Haptic & audible button feedback options
- U/UTP Cat5 cable connection
- Multi-command macros
- IR learning facility
- SD card configuration upload
- Easy to program
|
|
This universal 7" touchscreen wallplate is the perfect control system for commercial and domestic automation. Its stylish low profile design lends itself to installation in new modern homes, classrooms, lecture theatres or corporate boardrooms. |
|
A6531 |
|
- User programmable buttons & icons
- Multiple screen pages (12 max)
- Tandem operation
- Event splash screens
- Icon library for commonly used buttons
- Infra-red control output
- RS-232 or RS-485 serial outputs
- PIR motion trigger
- Haptic & audible button feedback options
- U/UTP Cat5 cable connection
- Multi-command macros
- IR learning facility
- SD card configuration upload
- Easy to program
|
|
This universal 7" touchscreen wallplate is the perfect control system for commercial and domestic automation. Its stylish low profile design lends itself to installation in new modern homes, classrooms, lecture theatres or corporate boardrooms. |
|
C7204 |
|
|
|
Rugged heavy duty nylon cover custom made to suit the C7202C portable PA system. |
|
C7200 |
|
|
|
Protective poromeric pouch to suit C7195A or C7195B beltpack lavalier transmitter. |
|
A4270 |
|
- Multi-stage thermally cued fan cooling
- 2U 19” rack mount (with optional A 4376)
- Tape record out terminals
- Provision for connection to Redback A4660 touchscreen paging console
- MP3 based Alert/Evac tones with MP3 voice over message for emergency tones (built in)
- 3 mic input and 4 auxiliary inputs
- Phantom powering available on all inputs
- Adjustable vox muting on inputs 1 & 2.
- Bass and treble tone controls
- Terminals for 100V line output
- 240V AC or 24V DC power operation
- Thermal & fuse overload protection
- Built in short circuit protection
- Australian designed & assembled
|
|
Similar in functionality to the recently released A 4377/A4387 amplifiers with the addition of four 100V line output zones. |
|
A4280 |
|
- Multi-stage thermally cued fan cooling
- 2U 19” rack mount (with optional A 4376)
- Tape record out terminals
- Provision for connection to Redback A4660 touchscreen paging console
- MP3 based Alert/Evac tones with MP3 voice over message for emergency tones (built in)
- 3 mic input and 4 auxiliary inputs
- Phantom powering available on all inputs
- Adjustable vox muting on inputs 1 & 2.
- Bass and treble tone controls
- Terminals for 100V line output
- 240V AC or 24V DC power operation
- Thermal & fuse overload protection
- Built in short circuit protection
- Australian designed & assembled
|
|
Similar in functionality to the recently released A 4377/A4387 amplifiers with the addition of four 100V line output zones. |
|
A4377A |
|
- 3 Balanced microphone inputs / 3 Aux inputs / 1 Music input
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 100V standard with optional 70V and 4-16Ω outputs
- 240V AC or 24V DC operation
- VOX muting on inputs 1 and 2 (Switch selectable internally)
- Adjustable VOX level sensitivities
- Bass and Treble controls
- Tape Output
- Phantom power on microphone inputs (DIP switch selectable internally)
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicator
- Half power mode when overdriven
- Fault Indicators
- 24V DC Power Status Indicator
- Optional Alert/Evac module with voice over message for emergency tones (A 4573)
- Optional remote volume (With A 4373 Digital volume control module fitted and external A 2280B wall plate)
- Rack Mountable (suits 19 inch racks) with optional A 4376 rack ears
|
|
This 125 Watt 4 channel mixer amplifier is specifically designed for applications requiring up to three microphone inputs, without compromising output power and overall performance. The amplifier feature three inputs which can be configured for either microphone or line level operation. |
|
A4379 |
|
- 6 Balanced microphone inputs / 6 Aux inputs / 1 Music input
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 100V standard with optional 70V and 4-16Ω outputs
- 240V AC or 24V DC operation
- VOX muting on inputs 1 and 2 (Switch selectable internally)
- Adjustable VOX level sensitivities
- Bass and Treble controls
- Tape Output
- Phantom power on microphone inputs (DIP switch selectable internally)
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicator
- Half power mode when overdriven
- Fault Indicators
- 24V DC Power Status Indicator
- Optional Alert/Evac module with voice over message for emergency tones (A 4573)
- Optional remote volume (With A 4373 Digital volume control module fitted and external A 2280B wall plate)
- Rack Mountable (suits 19 inch racks) with optional A 4376 rack ears
|
|
Designed for applications requiring up to six microphone inputs, without compromising output power and overall performance. Each model features inputs which can be configured for either microphone or line level operation. |
|
A4387A |
|
- 3 Balanced microphone inputs / 3 Aux inputs / 1 Music input
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 100V standard with optional 70V and 4-16Ω outputs
- 240V AC or 24V DC operation
- VOX muting on inputs 1 and 2 (Switch selectable internally)
- Adjustable VOX level sensitivities
- Bass and Treble controls
- Tape Output
- Phantom power on microphone inputs (DIP switch selectable internally)
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicator
- Half power mode when overdriven
- Fault Indicators
- 24V DC Power Status Indicator
- Optional Alert/Evac module with voice over message for emergency tones (A 4573)
- Optional remote volume (With A 4373 Digital volume control module fitted and external A 2280B wall plate)
- Rack Mountable (suits 19 inch racks) with optional A 4376 rack ears
|
|
This 250 Watt 4 channel mixer amplifier is specifically designed for applications requiring up to three microphone inputs, without compromising output power and overall performance. The amplifier feature three inputs which can be configured for either microphone or line level operation. |
|
A4389 NEW
|
|
- 6 Balanced microphone inputs / 6 Aux inputs / 1 Music input
- Robust design incorporating latest Mosfet technology
- Very Low noise and distortion
- 100V standard with optional 70V and 4-16Ω outputs
- 240V AC or 24V DC operation
- VOX muting on inputs 1 and 2 (Switch selectable internally)
- Adjustable VOX level sensitivities
- Bass and Treble controls
- Tape Output
- Phantom power on microphone inputs (DIP switch selectable internally)
- Multi stage thermally cued fan cooling
- Output Peak Limited
- Thermal Overload protected
- Signal Presence Indicator
- Half power mode when overdriven
- Fault Indicators
- 24V DC Power Status Indicator
- Optional Alert/Evac module with voice over message for emergency tones (A 4573)
- Optional remote volume (With A 4373 Digital volume control module fitted and external A 2280B wall plate)
- Rack Mountable (suits 19 inch racks) with optional A 4376 rack ears
|
|
Designed for applications requiring up to six microphone inputs, without compromising output power and overall performance. Each model features inputs which can be configured for either microphone or line level operation. |
|
H5295 |
|
|
|
Includes 2 free wheeling and 2 with locking mechanisms. Suits all rack frames. |
|
H5296 |
|
|
|
Heavy duty caster wheels to suit HD5506 to HD5522 450mm deep rack frames. |
|
C8889 |
|
|
|
Rack mounting ears to suit C8860, C8870 and C8890 series of UHF receivers. |
|
P8167 |
|
- Overload protection
- Both IEC and Australian Sockets
- Rack ear mounting
- Power cord located at the rear
- High surge protection
- 240V a.c. 10A
|
|
The neat solution to supplying mains power to your mounted equipment. |
|
P8166 NEW
|
|
- 240V AC 10A outputs.
- 7 x Australian Sockets (AS/NZS 3112:2017 conforming).
- Electrical authority outlet device approved (AS/NZS 3105:2014 conforming).
- High surge protection.
- Overload protection.
- Power cord located at the rear for less interference.
- 19” rack ear mounting.
|
|
The neat solution to supplying mains power to your mounted equipment. |
|
A4946 |
|
|
|
The Redback A 4946 receives audio from compatible Redback Cat5e/6 transmitters, converts the signal to line level and outputs to RCA and 3.5mm connectors. |
|
A4944 |
|
|
|
The Redback® A 4944 provides a convenient way to send line level RCA audio signals over long distances via Cat5/6 cabling. The unit has DIP switch selectable input sensitivities of 100mV and 1V to handle inputs of varying levels.
|