|
Description |
Downloads |
Specs |
Ordering |
|
 |
Z6587 NEW
|
|
- Easy, wireless communication up to 100m
- Create your own network of connected devices.
- Compact, on-board antenna
- 915MHz is suitable for amateur use in Australia.
- No soldering necessary
- 2x LEDs: Rx/Tx indicator, and user-controllable
- PiicoDev connector, compatible with Qwiic and STEMMA QT (3.3V only)
- 2.54mm breakout for breadboarding/prototyping
|
|
With this Transceiver users can unlock some very cool capabilities like collecting data from some distant sensor, or remote-controlling hardware. |
 |
Z6316 NEW
|
|
- Easy to set up and pair - Android or iOS eWeLink app available for direct control.
- Onboard Bluetooth status indicator and relay indicator.
- With 2 optocoupler isolation, strong anti-interference ability.
- Onboard N76E003/STM8S003 and SPP-C Bluetooth 2.1 module.
- Compact board design.
- Module with diode effusion protection short response time
|
|
A combined relay and control board with the ability to switch on and off connected loads using an App on your phone via Bluetooth. The eWeLink app offers seamless power switching using your device when in range of the relay board (typically 10m). |
 |
Z6319 NEW
|
|
- Large 3-digit display of measured temperature
- Operates in both a heating and cooling mode of operation
- Programmable settings for temp set point, temp hysteresis, compressor delay and temperature calibration.
- Waterproof NTC temperature sensor has -50 to +99.9°C measurement range with ±1°C accuracy
- Over temperature and sensor failure audible and visual alarm
- Unit temperature reading can be calibrated
- Relays switch up to 120/240VAC @ 10A or 15VDC @ 10A
- 12VDC module operation
|
|
The STC-1000 temperature controller is a self contained heating / cooling controller that operates on 12VDC and controls either AC or DC loads up to 10A max current. |
 |
J0064 NEW
|
|
- Gear Ratio: 90:1
- Input Voltage: 12V
- No Load
- Speed: 66RPM
- Current: 0.3A
- Rated Load
- Speed: 50RPM
- Current: 1A
- Torque: 17kg-cm
- Stall Load
- Current: 3.8A
- Torque: 35kg-cm
|
|
This gearbox is suitable for a host of model and light industrial applications |
 |
H8958A NEW
|
|
- Great for better heat dissipation on the Pi 5.
- Access to all Pi Ports: Power, Video, Audio, USB, LAN, MicroSD Card.
- Slots for camera cables and GPIO access.
- Compatible with the Raspberry Pi 5.
- Includes cooling fan with header connection.
- Integral heatsink for added cooling efficiency.
|
|
This compact multi-layer acrylic case suits the Raspberry Pi 5 and provides access to all ports on the board. Includes cooling fan module with heatsink. |
 |
K8601 NEW
|
|
- Double sided PEI coated plate
- Excellent flatness & elasticity
- Strong adhesion
- Durable and long lasting textured plate
|
|
Double sided black textured PEI spring steel magnetic build plate to suit 3D printer models K8600 & K8602 |
 |
Z6240A NEW
|
|
- Form factor compatible with earlier series of Arduino boards for compatibility with existing shields and projects.
- Expanded memory and faster clock speed
- Extra on-board peripherals including 12-bit DAC, CAN BUS and OP Amp.
- Wider input voltage range for integration with motors, LED strips and actuators.
- SWD connector for debugging.
- HID support for keystrokes and mouse movement.
|
|
Introducing the Funduino UNO R4 Minima compatible Arduino board. Equipped with the RA4M1 microprocessor, this board offers enhanced processing power, expanded memory, and more, all while maintaining the reliable UNO form factor and practical 5V operating voltage. Get ready for a remarkable upgrade! |
 |
J0070A NEW
|
|
- Step Angle: 1.8Deg
- Temperature Rise: 80DegC max
- Ambient Temperature: -20DegC~+50DegC
- Insulation Resistance: 100 MOhm Min. ,500VDC
- Dielectric Strength: 500VAC for 1minute
- Shaft Radial Play: 0.02Max. (450g-load)
- Shaft Axial Play: 0.08Max. (450g-load)
- Max. radial force: 28N (20mm from the flange)
- Max. axial force: 10N
- Product description: 42 two-phase stepping motor Body length 34mm Static torque 2.2kg.cm
- 5mm shaft diameter with flat wire, length 24mm,
- Wiring method: black green A +, A-. Red blue B +, B-,
- Adapter driver JK0220 (driving voltage DC12V ~ 36V, AC12V ~ 24V, current range 0.3A ~ 2.0A)
|
|
12V 200-step 1.8° 48BYG stepper motor with interface
lead. 2 phase type. 0.23Nm holding torque. 5mmØ
shaft. NEMA17 M3 mounting hole pattern (31mm).
Size: 42x42x34 (25mm shaft). 1m lead. |
 |
A0724 NEW
|
|
- Operating voltage: 12 V/DC (11 - 14 V)
- Power consumption: approx. 2 mA/35 mA (relay off/on)
- Relay contact: 1 x SWITCH OVER, loading capacity max. 25 V, 3 A
- Operating temperature range: approx. -15 to +50°C
- Luminous intensity switching-on: approx. 25 lux ±20%
- Luminous intensity switching-off: approx. 45 lux ±20%
- Switching delay: approx. 3 - 4 seconds
- Dimensions: approx. 72 x 50 x 32mm (without fastening straps, with sensor)
|
|
Kemo M122 switch allows users to switch lamps or other electric devices on or off at dusk or daybreak. The sensitivity of the luminous intensity may be changed by partially covering the sensor mechanically. |
 |
H8960A NEW
|
|
- Great for better heat dissipation on the Pi 5.
- Access to all Pi Ports: Power, Video, Audio, USB, LAN, MicroSD Card.
- Compatible with the Raspberry Pi 5.
- Includes cooling fan with header connection.
- Includes 3 heatsinks.
|
|
An all metal Raspberry Pi 5 case with internal cooling fan and heatsinks. |
 |
Z6439B NEW
|
|
- On board speaker
- MEMs Microphone with LED indicator
- Touch sensitive logo
- Built-in sleep/off mode that means the board can be powered-down with batteries connected
- Discrete regulator that can supply up to 190mA of current to external accessories
- 25 Programmable LEDs in a 5 x 5 grid
- 3-axis motion sensing
- On-board magnetometer
- On-board temperature sensor
- On-board light level sensing
- 2 x programmable buttons, A & B
- BLE Bluetooth 5.0
- 2.4Ghz Micro:bit Radio
- Rear-mounted push button
- Power off (push and hold power button)
- 25 pins
- MEMS microphone and LED indicator
- Onboard speaker
- Touch-sensitive logo pin
- LED power indicator
- C++, MakeCode, Python, Scratch
|
|
The Micro:bit is easy to code with, all you need is your web browser and a micro USB cable and you are ready to start all kinds of exciting STEM/STEAM experiments, no need for any extra software to be installed. Micro:bit has also developed a mobile app for coding over Bluetooth (without a USB cable), that makes it even easier to get everyone codin |
 |
Z6433 NEW
|
|
- XTensa dual-core 32-bit LX7 CPU, frequency up to 240MHz
- 2.4 GHz Wi-Fi, EEE 802.11 b/g/n-compliant
- Bluetooth, LE: Bluetooth 5, Bluetooth mesh
- 16 MByte(64Mbit) SPI Flash
- 384 KByte ROM
- 512 KByte SRAM
- 8 MByte(64Mbit) SPI PSRAM
- 16 KB SRAM in RTC
- Communication Interfaces: 2 x I2C, 2 x I2S, 4 x SPI, 3 x UART, 1 x USB OTG
- Security: 4096 bit OTP, AES, SHA, RSA, ECC and RNG, Secure boot, Flash encryption, Digital signature, HMAC module
- Dual Type-C USB connectors
- Reset and User/Firmware buttons
- RGB WS2812 User LED
- Power LED
- Virtual USB port provided by CP2102 for debugging and firmware upgrade
- Compact size of 50.1 x 13mm
- Supply Voltage: 5V via USB
- Circuit Voltage: 3.0 to 3.6V Circuit Operation
|
|
The ESP32-S3 development board is assembled with an original ESP32-S3-WROOM-1 module from Espressif, with 16MB Flash and 8MB PSRAM(ESP32-S3-WROOM-1-N16R8). It is a general-purpose Wi-Fi + Bluetooth® LE MCU module that integrates complete Wi-Fi and Bluetooth LE functions. |
 |
Z6589 NEW
|
|
- Intuitive output: Air Quality Index
- Measures VOCs and eCO2
- A great guide to get you started
- PiicoDev connector, compatible with Qwiic and STEMMA QT (3.3V only)
- 2.54mm breakout for breadboarding/prototyping
- Manufactured and supported in Australia by Core Electronics
|
|
PiicoDev ENS160 Air Quality Sensor. Measure indoor air-quality - sensitive to fumes, cooking smells, humans. |
 |
Z6527A NEW
|
|
- Support Arduino Mega2560 Directly inserted
- With Full-angle IPS TFT panel
- On Board level conversion chip for 5V/3.3V MCU
- Compatible with 2.8~3.3V operation voltage level
- Compatible with Arduino-Series development Board.
- Provided 12-examples with Arduino ,3-examples with STM32
- With SD Card Socket
- With SPI FLASH circuit
|
|
A 480x320 display shield for the Arduino Mega utilising the ILI9486 chipset. Ideal for projects requiring sensor monitoring. |
 |
A0713 NEW
|
|
- Operating voltage: 12 - 15 V/DC
- Current consumption: approx. 20 mA / 80 mA (relay off / on)
- Adjustable time: approx. 2 sec. to 23 min., (± 30 %)
- Connection: via flat-pin plug at the module
- LED: 2 (1 x LED operating voltage, 1 x LED relay “ON”)
- Relay point: 1 x ON, max. 3A, max 25V
- Dimensions: approx. 87 x 60 x 33 mm (with flanges)
|
|
Avoid the hassle with this pre-assembled timing controller, conveniently packaged in a compact and reliable form. It's easy to connect and versatile enough to adapt to your requirements. The start and stop functions are managed by simple switching contacts, and the relay output can control devices up to 25VDC at 3A. |
 |
Z6440B NEW
|
|
- On board speaker
- MEMs Microphone with LED indicator
- Touch sensitive logo
- Built-in sleep/off mode that means the board can be powered-down with batteries connected
- Discrete regulator that can supply up to 190mA of current to external accessories
- 25 Programmable LEDs in a 5 x 5 grid
- 3-axis motion sensing
- On-board magnetometer
- On-board temperature sensor
- On-board light level sensing
- 2 x programmable buttons, A & B
- BLE Bluetooth 5.0
- 2.4Ghz Micro:bit Radio
- Rear-mounted push button
- Power off (push and hold power button)
- 25 pins
- MEMS microphone and LED indicator
- Onboard speaker
- Touch-sensitive logo pin
- LED power indicator
- C++, MakeCode, Python, Scratch
|
|
The Micro:bit go kit is easy to code with, all you need is your web browser and a micro USB cable and you are ready to start all kinds of exciting STEM/STEAM experiments, no need for any extra software to be installed. Kit includes USB cable, batteries and battery holder. |
 |
ZW6240A NEW
|
|
- Form factor compatible with earlier series of Arduino boards for compatibility with existing shields and projects.
- Expanded memory and faster clock speed
- Extra on-board peripherals including 12-bit DAC, CAN BUS and OP Amp.
- Wider input voltage range for integration with motors, LED strips and actuators.
- HID support for keystrokes and mouse movement.
- Wi-FI and Bluetooth connectivity on board.
- Qwiic connector for I2C compatible sensors and actuators.
- LED matrix on board.
- Supports battery powered RTC.
|
|
The Funduino UNO R4 with WiFi is an Arduino compatible board integrating the powerful RA4M1 microcontroller with the robust wireless capabilities of the ESP32-S3 from Espressif. Additionally, it features an on-board 12x8 LED matrix, a Qwiic connector, a VRTC, and an OFF pin, making it an ideal choice for all your maker projects. |
 |
X3063 NEW
|
|
- 2.4G remote control, suitable for indoor and outdoor flight, can be played in the bedroom.
- Equipped with high-precision gyro control
- With landing gear, can take off in a short distance.
- Has lights on the bottom.
- Mini size, small turning radius for indoor flight.
- High and low-speed modes
- Very easy to control. Slow indoor flight, fast outdoor flight, with adjustable flight attitude structure at the tail.
- Can perform rolling stunts.
- Can perform leaf fall drifting
- Can perform cobra aerobatic flight.
|
|
Experience the thrill of flying with this remote control plane! This ingeniously designed plane operates at 2.4GHz, featuring a double-wing design for precise speed control and optimal flight stability. |
 |
K8671 NEW
|
|
- Build more than 72 robots from simple to complex, which contains a lot of robot knowledge such as machinery, gears, structure, transmission, etc.
- Enhance children's hand-on ability, DIY and logical thinking ability
- Different combinations of the motor and sensors greatly stimulate kids' to think scientifically.
- The control module of this educational toy also known as the "Intelligent Motor", contains 2 operation modes:"Electrical Mode" and "Intelligent Mode". The electric part makes it an excellent and amusing toy while the intelligent part is what specifically makes it SMART and DIFFERENT. (Batteries NOT included).
- Both the blocks and motor are compatible with almost all building sets. Spectacularly, with the great compatibility of the Intelligent Motor, it can power up motionless robots and make them move!
- Allows kids to explore grow their imaginations by building and creating projects by themselves
- With the Makerzoid App from App Store and Google Play, kids can assemble the robots easily through the graphic instructions and control the motorized robot to move in all directions with the robotics kit.
- Available through the free app, Scratch 3.0 reduces the difficulty of coding - just to drop a few orders into the "Coding" section then the robot can react on your demand.
- This set is packed in a storage box to help children develop a good habit of packing and collecting their own toys.
|
|
This 300pc set contains the parts for 72 different project designs which can be built using Makerzoids 3D app tutorials. |
 |
Z6315A NEW
|
|
|
|
A handy parts kit containing everything you need to start learning Arduino and building projects. Includes a huge selection of sensor boards, LEDs, pots, jumper wires, a breadboard, LCD screen and much more! |
 |
Z6296 NEW
|
|
|
|
Get your brand new Raspberry Pi Zero 2 W with most of the essentials in this kit. |
 |
Z6516A NEW
|
|
- 7’’ standard display, 1024x600 resolution
- Capacitive touch screen, maximum support 5 point touch
- Supports backlight control, the backlight can be turned off to save power
- Supports standard HDMI interface input.
- Can be used as general-purpose-use HDMI monitor, for example: connect with a computer HDMI as the sub-display (resolution of the output has to be able to adjust to 800X480)
- Used as a Raspberry Pi display that supports Raspbian, Ubuntu, Kodi, win10 IOT, single-touch, free drive etc.
- Works as a PC monitor, support win7, win8, win10 system 5 point touch (XP and older version system: single-point touch), free drive.
|
|
A 1024x600 touchscreen for Raspberry Pi that supports standard HDMI interface input which can be directly connected to Raspberry Pi. |
 |
Z6302J NEW
|
|
- Broadcom BCM2712 quad-core Arm Cortex A76 processor @ 2.4GHz
- RAM variants up to 8GB
- Interchangeable Camera and DSI display connectors
- Dual 4Kp60
- Real-time clock
- Power button
- UART debug port
|
|
The Raspberry Pi 5 4GB single board computer. The bandwidth speed and performance of the new Raspberry Pi 5 is a step up from earlier models. |
 |
K8670 NEW
|
|
- Over 26 robots can be assembled as well as custom projects
- Incorporates 2 integrated motors and 2 IR sensors (batteries NOT included) to allow for intelligent, smooth moving robotic projects
- Allows kids to explore grow their imaginations by building and creating projects by themselves
- With the Makerzoid App from App Store and Google Play, kids can assemble the robots easily through the graphic instructions and control the motorized robot to move in all directions with the robotics kit.
- Available through the free app, Scratch 3.0 reduces the difficulty of coding - just to drop a few orders into the "Coding" section then the robot can react on your demand.
- Superbot brings you endless fun in building, playing then battling with their car models together which makes it the new pop in any kids' theme party.
- The set is packed in a clear storage box to help children develop a good habit of packing and collecting their own toys.
|
|
A 400pc set allowing kids to build up to 26 different projects, and create designs of their own. Includes control unit and intelligent sensors (2) that allow building of line tracking, obstacle avoiding and following robot designs. Blocks are compatible with other major brands. Fully programmable using Scratch. Includes storage box. |
 |
K8672 NEW
|
|
- Build more than 100 robots from simple to complex, which contains a lot of robot knowledge such as machinery, gears, structure, transmission, etc.
- Both Children and parents will enjoy the fun of building a robot and making a programming for it.
- Helps develop children's mind, DIY and logical thinking ability.
- Set is equipped with 23 robotics courses for kids to learn how to build, control and code at home while playing with this toy set.
- Incorporates 2 integrated motors and 2 IR sensors (batteries NOT included) to allow for intelligent, smooth moving robotic projects
- Allows kids to explore grow their imaginations by building and creating projects by themselves
- With the Makerzoid App from App Store and Google Play, kids can assemble the robots easily through the graphic instructions and control the motorized robot to move in all directions with the robotics kit.
- Available through the free app, Scratch 3.0 reduces the difficulty of coding - just to drop a few orders into the "Coding" section then the robot can react on your demand.
- The set is packed in a big storage box to help children develop a good habit of packing and collecting their own toys. And the sorting plate will be less time-consuming because kids could organise the building blocks based on the colour and size.
|
|
The Robot Master sets supports the building of up to 200 different robotic projects from simple to complex, allowing kids to progress their STEM skills up with staged lessons. |
